fantastic furniture Torkay Lamp Table 1 Drawer White Walnut User manual

Version 1.0
Java
Lamp Table 1 Drawer
fantasticfurniture.com.au
Required
Two People

fantasticfurniture.com.au Page 2
Warning: Ensure the wall strap is attached
to avoid serious injury
To avoid any serious or fatal injury, a wall strap has been provided with
this product to prevent toppling. We strongly recommend that this
product is permanently fixed to the wall or other suitable surface. Fixing
of what fixing device to use.
Rattan
Rattan is a natural material that will respond to humidity in the
environment. Low humidity may cause the rattan to shrink.
High humidity may cause the rattan to absorb moisture and expand,
causing the weaving to look loose and wavy.
This is a natural phenomenon and not a defect.
Looks like you’ve found
your Fantastic!
Love it? Share it!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
Fantastic buy! Share how it looks at home on Instagram
for your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au Page 3

Parts list
1 x Top Panel (P1)
1 x Bottom Panel (P2)
2 x Side Panels (P3)
1 x Back Panel (P4)
1 x Drawer Front (P5)
1 x Drawer Left Side (P6)
1 x Drawer Right Side (P7)
1 x Drawer Back (P8)
1 x Drawer Base (P9)
4 x Legs (P10)
Top Panel (P1)
What you need
to assemble the product
Other tools you need
Flat Head Screwdriver;
Phillips Head Screwdriver;
Mallet
fantasticfurniture.com.au
Page 4
Bottom Panel (P2)
Side Panel
(P3)
Side Panel
(P3)
Back Panel
(P4)
Drawer Front
(P5)
Drawer Back
(P8)
Drawer Base
(P9)
Leg (P10)
Leg (P10)
Leg (P10)
Drawer Left
Side (P6)
Drawer Right
Side (P7)

fantasticfurniture.com.au
Page 5
Hardware Pack
12 x Cam Bolts
(H1)
8 x Large Cam
Nuts (H2)
8 x Dowels ø8mm
(H3)
1 x Handle
(H4)
4 x Screws 16mm
(H6)
10 x Flat Washers
(H9)
8 x Spring
Washers (H10)
2 x Screws 28mm
(H11)
1 x Allen Key
(H12)
4 x Felt Feet
(H5)
8 x Bolts
(H8)
4 x Back Panel
Connectors (H7)
1 x Screw 25mm
(H14)
4 x Small Cam
Nuts (H15)
1 x Wall Strap
(H13)
2 x Dowels ø6mm
(H16)
4 x Screws 38mm
(H17)
2 x Slides
(H19)
12 x Screws 12mm
(H18)

Step 1
Page 6fantasticfurniture.com.au
You will need
Attach 1 x felt foot (H5) onto each leg (P10) as shown.
Step 2
You will need
8 x Bolts
(H8)
Attach 1 x leg (P10) onto bottom panel (P2),
using 2 x bolts (H8), 2 x flat washers (H9)
and 2 x spring washers (H10).
Tighten the bolts with allen key (H12).
Repeat this step for the other 3 x legs (P10).
Turn the assembled unit over.
(P10)
4 x Felt Feet
(H5)
X4
H5
8 x Flat
Washers (H9)
8 x Spring
Washers (H10)
1 x Allen Key
(H12)
Step 3
You will need
(P2)
H1
H1
H1
H1
Screw 4 x cam bolts (H1)
into bottom panel (P2),
using a phillips head screwdriver.
4 x Cam Bolts
(H1)
Phillips Head
Screwdriver
(P10)
H12
H8
H9
H10
(P2)
(P10)
(P10)
(P10)
(P2)
(P10)

Step 4
Page 7fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
6 x Screws
12mm (H18)
2 x Slides
(H19)
Mallet
H19
Separate the 2 x slide runners (H19-2) and slide tracks (H19-1)
from the slides (H19) by following the steps below:
Extend the slide runner (H19-2) all the way out.
Press down the plastic release lever on the slide and pull out
the slide runner (H19-2) completely.
H19
Slide runner H19-2 Slide track H19-1
H19-1
H19-1
Note the position
of the rubber stopper
Attach 2 x separated slide tracks (H19-1) onto 2 x side panels (P3) with 6 x screws (H18),
using a phillips head screwdriver as shown.
Ensure the slide tracks (H19-1) are attached so the rubber stopper is near the gooves
on the panels.
Insert 4 x dowels (H3) into each panel (P3) as shown.
Use a mallet to gently tap the dowels into place if needed.
Adjust runner to access the screw holes.
H19-1
8 x Dowels
ø8mm (H3)
H18
(P3)
H3
H3
H3
H3
X2
H18
H18 H19-1
Please fasten the screws through
these holes for this step.

Step 5
Page 8fantasticfurniture.com.au
You will need
Position the 2 x side panels (P3) onto bottom panel (P2), making sure the grooves
on side panels and bottom panel are on the same side.
Insert 4 x large cam nuts (H2) into side panels (P3).
Rotate the cam nuts so the arrows
point towards the incoming cam bolts
. Using a flat head screwdriver, turn clockwise to lock.
Flat Head
Screwdriver
4 x Large Cam
Nuts (H2)
(P2)
(P3)
H2
H2
H2
H2
(P2)
(P3)
(P3)
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Step 6
Slide back panel (P4) into
the grooves of the side panels
and bottom panel (P3, P2).
(P4)
(P3)
(P2)
(P3)

Step 7
Page 9fantasticfurniture.com.au
You will need
Flat Head
Screwdriver
4 x Large Cam
Nuts (H2)
(P1)
Phillips Head
Screwdriver
4 x Cam Bolts
(H1)
Step 8
You will need
Screw 4 x cam bolts (H1) into top panel (P1), using a phillips head screwdriver.
Position top panel (P1) onto assembled unit as shown.
Insert 4 x large cam nuts (H2) into panels (P3).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Using a flat head screwdriver, turn clockwise to lock.
H1
H2
H1
H1
H1
(P1)
(P3)
(P3)
H2
H2
H2

Step 9
Page 10fantasticfurniture.com.au
You will need
Step 10
You will need
H1 (P5)
H1
H1
H1
Screw 4 x cam bolts (H1) into drawer front (P5), using a phillips head screwdriver as shown.
Phillips Head
Screwdriver
4 x Cam Bolts
(H1)
If necessary, gently adjust the top panel (P1) sideways
in either direction until XX and YY are equal.
Holding it in place, fix 4 x back panel connectors (H7)
to assembled unit with 4 x screws (H6) as shown, using a phillips head screwdriver.
Phillips Head
Screwdriver
(P4)
4 x Screws
16mm (H6)
4 x Back Panel
Connectors (H7)
H7
H7
H7
H7 H7
H6 (P4)
H7
Required
Two People
XX
YY
XX=YY
XX
YY
(P1)
(P1)
(P4)
(P1)
(P1)