fantastic furniture MEMPHIS User manual

ver6.5

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws（leave slightly
loose.When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

(tools not provided)
Phillips Head Srewdriver
Flat Head Screwdriver
Mallet
What You Need
Page 3
1 x Socket Wrench
12 x Dome Head
Screws
(H1)
26 x Small Cam
Nut and Bolts
(H2)
16 x Big Cam
Nut and Bolts
(H3)
20 x Wooden
Dowels
(H4)
20 x Short
Timber Screws
(H5)
4 x Drawer
Runner Track
(H6)
4 x Glass Clamps
(H7)
2 x Short
Threaded Rod
(H8)
2 x Long
Threaded Rod
(H13)
2 x Stainless
Steel Tube
(H9)
2 x Tube
Cover
(H10)
4 x Washer
(H11)
4x Drawer Sides
(P10)
2x Drawer Front
(P9)
2x Drawer Back
(P13)
2x Drawer Shelf
(P12)
4 x Nut
(H12)
10 x Long
Screws
(H14)
4 x Drawer
Runners
(H15)
4 x Bolts
(H16)
2 x Drawer
Handle
(H17)
Please check that you have everything before starting the assembly.
Long Base Panel
(P1)
2x
Drawer Top Panel
(P5)
2x
Panel Glass Divider
(P6)
4x
Side Panels
(P3)
2x BackPanel
(P4)
6x Wooden Block
(P2)
Lower Glass
(P8)
Top Glass
(P7)
2x Drawer Support
(P11)

Carefully align the edges of the Wooden Blocks (P2) with the edges of Long Base Panel (P1), then
x with 12 x Dome Head Screws (H1)
Insert 8x Small Cam Bolts (H2) into 4x Side Panels (P3).
Step 3
8x Small Cam Bolts
(H2)
You will need:
8 x Small Cam
Nuts
(H2)
(H2)
Insert the 8x Small Cam Nuts (H2) into the Back Panels (P4).
(P4)
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push the Side Panels into place and tighten the cam nuts.
Repeat for both drawers boxes.
This is how a cam nut works........
The head of the bolt
goes into the wide
mouth of the cam nut.
You then turn the nut
so the narrow part
closes over the bolt.
12 x Dome Head
Screws
(H1) (P1)
(P3)
(P3)
(H2)

Page 5
Step 4
You will need:
4 x Small Cam
Bolts
(H2)
(H2)
(H2)
(H2)
(H2)
8x Big Cam
Bolts
(H3)
(H3)
8 x Wooden
Dowels
(H4)
(H4)
(H3)
(H4)
(H3)
(H4)
(H3)
(H4)
(H3)
(H4)
(H3)
(H4)
(H3)
(H4)
(H3)
(H4)
Insert 4x Small Cam Bolts (H2), then 8x Big Cam Bolts (H3) and 8x Wooden Dowels (H4)
into the Long Base Panel (P1).
Step 5
You will need:
8 x BigCam
Nuts
(H3)
(H3)
(P4)
(P3)
4 x Small Cam
Nuts
(H2)
(H2)
Insert 4x Small Cam Nuts (H2) into the Back Panels (P4) and 8x Big Cam Nuts (H3)
into the Side Panels (P3).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push the Back and Side Panels into place and tighten the cam nuts.
Repeat for both drawer boxes.
Mallet
(P4)
(P3)
(P1)

6
Step 8
Step 7
You will need:
4x Small Cam
(H2)
8x Big Cam
Nuts
Nuts
(H3)
Insert 4x Small Cam Nuts (H2)
into the Back Panels, then
8x Big Cam Nuts into Side Panels (P3).
Rotate the cam nuts so the arrows point
towards the incoming cam bolts.
Push the Drawer Top Panel (P5) into place and tighten the cam nuts.
You will need:
4x Small Cam
Bolts
(H2)
(H2)
(H2)
(P5)
8 x Big Cam
Bolts
(H3)
(H3)
(H3)
(H3)
(H3)
8x Wooden
Dowels
(H4)
(H4)
(H4)
(H4)
(H4)
Insert 4x Small Cam Bolts (H2), 8x Big Cam Bolts (H3) and 8x Dowels (H4) into Drawer Top Panels (P5).
(H3)
(H3)
(H2)
(H3)
(P5)
(P3)
Step 6
You will need:
12 x Short Timber
(H5)
Screws
4 x Drawer Runner
(H6)
Tracks
(H5)
(H5)
(H5)
(H5)
(H5)
(H5)
(H6)
front
Attach 4x Drawer Runner Tracks (H6),
to Side Panels with 12x Short Timber
Screws (H5).
Note:
Attach screws loosely. Then tighten the
front screw first, making sure the screw
aligns in the centre of the hole in the drawer runner.
Then tighten the other screws.
CR
CR

7
Fix 4x Glass Clamps (H7) to both Panel Glass Dividers (P6).
Step 9
You will need:
4x Glass Clamps
(H7)
(P6)
Step 10
(H7)
Tighten with phillips
head screwdriver
You will need:
Inset 4x Wooden Dowels (H4) into
Base Panel, then push both
Panel Glass Dividers onto dowels.
4 x Wooden
Dowels
(H4)
Fix Short Threaded Rods (H8) into discs on Top Glass (P7). Tighten by hand.
Step 11
You will need:
2 x Short
Threaded Rod
(H8)
(H8)
(H8)
(P7)

8
Step 12
You will need:
2 x Steel Tubes
2 x Tube Cover
(H9)
(H9)
(H10)
(H10)
2 x Nuts
(H12)
(H12)
2 x Washers
(H11)
(H11)
You will need:
2 x Long Threaded
Rod
(H13)
(H13)
2 x Nuts
(H12)
(H12)
2 x Washers
(H11)
(H11)
Carefully lift glass into place over Steel Tube (H9) and Tube Cover (H10). Fasten with Washer (H11)
and Nut (H12). Tighten firmly with socket wrench.
Align Panel Glass Divider on aluminium block, then insert 2x Long Threaded
Rod (H13) and tighten by hand. Attach 2x Washers (H11) and Nuts (H12)
and tighten with Socket Wrench.
Step 13
Carefully turn over the unit.

Step 14
(P8)
9
Carefully turn over the unit and insert Lower Glass (P8) into Glass Clamps and tighten.
Use stubby at head
screw driver
Step 15
Now Assemble the Drawers
(P9)
10 x Small Cam
Bolts
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
You will need:
Screw 10x Small Cam Bolts (H2) into 2x Drawer Fronts (P9). Repeat for both drawer fronts.

You will need:
10 x Small Cam Nuts
(H2)
(P9)
(P12)
(P13)
Step 16
Step 17
Step 18
Insert the 10x Small Cam Nuts (H2) into the Drawer Sides (P10) and Drawer Support (P11).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Insert the Drawer Shelves (P12) into the grooves on Drawer Sides and Drawer Fronts,
then attach Drawer Backs (P13) with 10x Long Screws (H14). Repeat for both drawers.
Attach 4x Drawer Runners (H15) to the underside of the drawers,
with 8x Short Timber Screws (H5). Repeat for both drawers.
Push the Drawer Side and Drawer Support into place and tighten the cam nuts. Repeat for both drawers.
(P11)
(H2)
(H2)
(H2)
(P10)
(P10)
Page 10
10 x Long
Screws
(H14)
(H14)
(H5)
(H5)
(H5)
(H5)
(H15)
(H14)
(H14)
4 x Drawer Runners
(H15)
8 x Short Timber
Screws4(H5)