fantastic furniture COMO TALLBOY 6 DRW User manual

Version 1.0
Como
Tallboy 6 Drw
fantasticfurniture.com.au

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 10kgs /Drawer.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1); Left Side Panel (P2);
Right Side Panel (P3); Divider (P4);
3 x Rails (P5); Rails (P6); Rail (P7);
Rail (P8); Rail (P9); Rail (10);
2 x Back Panels (P11);
Connect Stick (P12);
Drawer Front (P13); Drawer Front (P14)
6 x Left Drawer Sides (P15);
6 x Right Drawer Sides (P16);
2 x Drawer Bases (P17);
2 x Drawer Backs (P18);
4 x Drawer Front (P19);
4 x Drawer Base (P20);
4 x Drawer Back (P21);
4 x Support Rail (P22)
Hardware pack
34 x Dowels
(H1)
33 x Long
Screws
(H2)
82 x Small
Screws
(H5)
6 x CL Runner
Tracks
(H6)
17 x Cam
Bolts
(H3)
17 x Cam Nuts
(H4)
28 x Small
Cam Nuts
(H11)
6 x CR Runner
Tracks
(H7)
6 x DL Runners
(H8)
6 x DR Runners
(H9)
28 x Small
Cam Bolts
(H10)
1 x Screw
(H13)
1 x Safety Strap
(H12)
2 x Washers
(H14)
4 x Plastic
Glides
(H15)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver; Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
Top Panel
(P1) Right Side
Panel
(P3)
Left
Drawer
Side(P15)
Left Drawer
Side(P15)
Drawer Front
(P19)
Drawer Front
(P13,P14)
×2 ×4
Right Drawer
Side(P16)
Right Drawer
Side(P16)
Drawer Back
(P21)
Drawer Back
(P18)
Drawer
Base(P20)
Drawer Base
(P17)
Support
Rail
(P22)
Left Side
Panel
(P2)
Rail
(P5)
Rail
(P5)
Rail
(P5)
Rail
(P6)
Rail
(P7)
Rail
(P8)
Rail
(P9)
Rail
(P10)
Divider
(P4)
Connect
Stick
(P12)
2 x Back
Panels
(P11)

You will need
Step 3
11 x Dowels
(H1)
Phillips Head
Screwdriver
15 x Small
Screws (H5)
H7
CR
H5
15 x Small
Screws (H5)
10 x Cam Bolts
(H3)
H5
H5
H7
H5 H5
H5
H7
H5 H5
H5
H7
H5 H5
H5
H7
H5 H5
H5
H7
H5
(P3)
You will need
Step 1
Step 2
You will need
Phillips Head
Screwdriver
Attach 5 x CL Runner Tracks (H6) to Left Side Panel (P2) with 15 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
Attach 5 x CR Runner Tracks (H7) to Right Side Panel (P3) with 15 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 5
5 x CL Runner
Tracks (H6)
H6
CL
H5
5 x CR Runner
Tracks (H7)
Phillips Head
Screwdriver
H5
H5
H5
H6
H5
H5
H5
H6
H5
H5
H5
H6
H5
H5
H5
H6
H5
H5
H5
H6
(P2)
H3
H3
H3
(P3)
(P2)
Insert 11 x Dowels (H1) into Left Side Panels (P2).
Attach 10 x Cam Bolts (H3) into Side Panels (P2) and (P3) as shown.
H1
H1
H1
H1
H1
H1 H1
H1 H1
H3
H3
H3
H1
H1
H3
H3
H3
H3

This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Step 5
You will need
Phillips Head
Screwdriver
Step 4
You will need
H7
CR
H5
3 x Small
Screws (H5)
Step 6
You will need
Phillips Head
Screwdriver
Attach 1 x CL Runner Track (H6) to Divider (P4) with 3 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
Attach 1 x Cam Bolt (H3) into Rail (P6). Insert 1 x Cam Nut (H4) into the hole of Divider (P4).
Rotate the cam nut so the arrow point towards the incoming cam bolt.
Push Divider (P4) into place and tighten the cam nut.
Attach Rail (P9) to Divider (P4) with 1 x Long Screw (H2).
Turn Divider (P4) over to the other side,then attach 1 x CR Runner Track (H7)
with 3 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
H5
H5
H5
H7
(P4)
H3
H4
(P4)
(P6)
(P9)
H2
1 x Long
Screws (H2)
fantasticfurniture.com.au
fantasticfurniture.com.au Page 6
H6
CL
H5
1 x CR Runner
Track (H7)
3 x Small
Screws (H5)
Phillips Head
Screwdriver
1 x CL Runner
Track (H6)
1 x Cam Bolts
(H3)
1 x Cam Nuts
(H4)
H5
H5
H5
H6
(P4)

11 x Dowels
(H1)
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
You will need
Step 7
Insert 11 x Dowels (H1) into 3 x Rails (P5)
and Rails (P6, P7, P8, P9, P10). Insert 5 x Cam
Nuts (H4) into the holes of Rails (P6) and
(P7, P8, P9, P10). Rotate the cam nuts so the arrows point
towards the incoming cam bolts. Push Right Side Panel (P3)
into place and tighten the cam nuts.
Insert 5 x Cam Nuts (H4) into the holes of Rails (P6) and
(P7, P8, P9, P10).Rotate the cam nuts so the arrows point
towards the incoming cam bolts.Attach 3 x Rails (P5) and
Rails (P6, P7, P8, P9, P10) to Left Side Panel (P2), then tighten the cam nuts.
(P9)
(P10)
(P5)
(P5)
(P5)
(P6)
(P7)
(P8)
(P2)
H4
H4
H4
H4
H4
H4
(P9)
(P8)
(P10)
(P5)
(P5)
(P5)
(P6)
(P7)
(P2)
(P3)
H4
H4
H1
H1
H1
H1
H1
H4
H1 H1
H1
fantasticfurniture.com.au Page 7
You will need
Step 8
Phillips Head
Screwdriver
5 x Cam Nuts
(H4)
Required
Two People
Required
Two People

You will need
Step 10
Join 2 x Back Panels (P11) with Connect Stick (P12),then put
into the groove on the back of the chest,screw it with 22 x Small Screws (H5).
Hammer 4 x Plastic Glides (H15) on Side Panels (P2) and (P3).
You will need
Step 9
Phillips Head
Screwdriver
Hammer
4 x Plastic
Glides (H15)
fantasticfurniture.com.au Page 8
22 x Small
Screws (H5)
(P2)
(P3)
H5
(P11)
(P11)
(P12)
H15
H15
H15
H15

8 x Dowels
(H1)
(P1)
H3
H3
H3
H3
H3
H3
Attach 6 x Cam Bolts (H3) into Top Panel (P1) as shown by tightening with the
Phillips Head Screwdriver.
fantasticfurniture.com.au Page 9
You will need
Step 11
Phillips Head
Screwdriver
You will need
Step 12
Phillips Head
Screwdriver
6 x Cam Bolts
(H3)
6 x Cam Nuts
(H4)
(P1)
(P2)
(P3)
(P4)
H1
H1
H1
H4
H4
H1
H4
Insert 8 x Dowels (H1) into the holes of Side Panels (P2,P3), Divider (P4) and Rail (P9).
Insert 6 x Cam Nuts (H4) into the holes of Side Panels (P2,P3) and Divider (P4).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts.

4 x Small
Cam Bolts (H10)
4 x Small
Cam Nuts (H11)
H10
H10
(P13)
H10 H10
fantasticfurniture.com.au Page 10
You will need
Step 13
Phillips Head
Screwdriver
You will need
Step 14
Phillips Head
Screwdriver
Step 15
Attach 4 x Small Cam Bolts (H10) into
Drawer Front (P13) by tightening with the
Phillips Head Screwdriver.
Insert 4 x Small Cam Nuts (H11) into the holes of Drawer Sides (P15,P16). Rotate the cam
nuts so the arrows point towards the incoming cam bolts. Push Drawer Side (P15,P16) into
place and tighten the cam nuts.
H11 H11
H11
H11
(P13)
(P15)
(P16)
(P13)
(P17)
(P15)
(P16)
Slide Drawer Base (P17) into the groove in
Drawer Sides (P15) and (P16).

4 x Long
Screws (H2)
1 x DL Runner
(H8)
1 x DR Runner
(H9)
4 x Small
Screws (H5)
fantasticfurniture.com.au Page 11
You will need
Step 17
Phillips Head
Screwdriver
Step 18
You will need
Step 16
Phillips Head
Screwdriver
Attach Drawer Back (P18) to Drawer Sides (P15)
and (P16) with 4 x Long Screws (H2),make sure that
the groove lines up the whole way around the drawer.
Attach 1 x DL Runner (H8) on the bottom of
Left Drawer Side (P15) and 1 x DR Runner (H9)
of Right Drawer Side (P16) with 4 x Small Screws (H5).
Repeat step 13 to step 17 with Drawer Front (P14)
to assemble the other drawer.
H2
(P13)
(P18)
(P15)
(P16)
H2
H2
H2
(P13) (P15)
(P16)
H9
H8
H5
H5
H5
H5
H9
DR
H5 H5
H8
DL
H5 H5
(P13)

1 x Dowel
(H1)
5 x Small Cam
Bolts (H10)
5 x Small
Cam Nuts (H11)
fantasticfurniture.com.au Page 12
You will need
Step 19
Phillips Head
Screwdriver
You will need
Step 20
Step 21
Phillips Head
Screwdriver
H10 H10
(P19)
H10
H10
H10
H1
Insert 1 x Dowel (H1) into Drawer Front (P19),and attach 5 x Small Cam Bolts (H10) into it.
H11 H11
H11
H11
H11
(P19)
(P15) (P22)
(P16)
Insert 5 x Small Cam Nuts (H11) into the holes of Drawer Sides (P15, P16) and Support Rail (P22).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push the Drawer Side (P15, P16) and the Support Rail (P22) into place and tighten the cam nuts.
(P19)
(P20)
(P15)
(P16)
Slide Drawer Base (P20) into the groove
in Drawer Sides (P15) and (P16).

1 x DL Runner
(H8)
1 x DR Runner
(H9)
4 x Small
Screws (H5)
You will need
Step 23
Phillips Head
Screwdriver
Step 24
fantasticfurniture.com.au Page 13
You will need
Step 22
Attach Drawer Back (P21) to Drawer Sides (P15)
and (P16) with 4 x Long Screws (H2), then attach Drawer
Back (P21) to Support Rail (P22) with 2 x Long Screws (H2).
Make sure that the groove lines up the whole way around the drawer.
H2
H2
H2
(P20)
(P21)
(P19)
(P15)
(P16)
H2
H2
H2
4 x Long
Screws (H2)
Phillips Head
Screwdriver
H9
H8
DR
DL
H5
H5
H5
H5
(P16)
(P15)
H9
H8
H5
H5
H5
H5
Attach 1 x DL Runner (H8) to the bottom of
Left Drawer Side (P15) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P16)
with 4 x Small Screws (H5).
Repeat step 19 to step 23 to assemble the rest of 3 x Drawers.

Please make sure your chest is sitting squarely on the floor, then tighten
all the screws and bolts – being careful not to over tighten
fantasticfurniture.com.au Page 14
Step 25
Insert the assembled drawers into the corresponding compartments as shown.
Ensure the drawers slide easily along the rails.
(P13)
(P14)

Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
Move the dresser to the final position, and attach the safety strap to the wall securely.
Make sure it is firmly attached and snug fit.
fantasticfurniture.com.au Page 15
You will need
Step 26
Phillips Head
Screwdriver
Phillips Head
Screwdriver
You will need
Step 27
We strongly advise that you use
the wall safety strap provided to
prevent the unit toppling
Seek advice from a qualified
trades person on how to
attach this safety strap to
your specific wall.
wall
Screw
H14
1 x Washer
(H14)
Screw and Wall Plug
are not provided.
Please use appropriate
fixtures for your wall.
1 x Safety
Strap (H12)
1 x Screw
(H13)
1 x Washer
(H14)
Attach Safety Strap (H12) to the Top Panel (P1) using 1 x Screw (H13) and 1 x Washer (H14).
H12
H13
H14