Ferno 430 Series User manual

1
© Ferno-Washington, Inc 234-3545-00 February 2014
Models 430, 430P, 439 Restraints
Important
Do not exceed the load limit of the equipment on
which the restraint is used. Refer to the equipment
users’manual for the equipment load limit.
Models 430, 430P, 439
Restraints
WARNING
Improper use of the restraint can cause injury. Attach and
use the restraint only as described in this manual.
Improper operation can cause injury. Operate the
restraint only as described in this manual.
Improper maintenance can cause injury. Maintain the
restraint only as described in this manual.
Description
Ferno®Models 430 and 430P Series Restraints (“the restraint”)
provide a variety of strapping options to help secure a patient on
an ambulance cot, stretcher, or other piece of emergency-medical
equipment (the “equipment”).
Model 430 Series are metal-buckle, primary-use restraints. Model
430P Series are plastic-buckle, secondary-use restraints. Select the
restraint that matches the intended use.
FERNO DEFINITIONS
● Primary-Use Restraints are suitable for securing a patient
on compatible equipment during transport in a motor vehicle.
● Secondary-Use Restraints ARE NOT suitable for securing
a patient during transport in a motor vehicle. They are for
temporary use to secure a patient on a backboard, hand-carried
stretcher, scoop stretcher, stair chair, or extrication device.
Transfer the patient onto an ambulance cot or other device
with primary restraints before transport in a motor vehicle.
● Transport Restraint SystemisdenedbyFernoasasetof
Primary-Use restraints used together to properly restrain a
patient in an ambulance.
Specications
All restraints provide length-adjustment. Restraints are available
with black or orange webbing, and in a variety of lengths. See the
chart at right.
● Model 430 are primary-use restraints. These restraints
feature a metal buckle and tang and are made of 51 mm (2")
nylon webbing
● Model 430P are secondary-use restraints. These restraints
feature a plastic buckle and tang and are made of 51 mm (2")
polypropylene webbing.
● Model 439 is a set of three, 1-piece, 7' (2134 mm) Model 430
metal-buckle restraints in a vinyl carrying bag.
Load Limit: Model 430 (Metal Buckle)
When properly attached and used in conjunction with additional
restraints (not supplied) as specied in the equipment users’
manual, the restraint is capable of securing a patient weighing the
maximum allowable load limit of the equipment. Do not exceed
the load limit of the equipment.
Load Limit: Model 430P (Plastic Buckle)
When properly attached and used in conjunction with additional
restraints (not supplied) as specied in the equipment users’
manual, the restraint is capable of securing a patient until transfer
to an ambulance cot or other device with primary restraints. Do not
exceed the load limit of the equipment.
Model 430 (Metal Buckle) Restraint
Model 430P (Plastic Buckle) Restraint
Male Buckle/TangFemale Buckle/Receiver
Male Buckle/TangFemale Buckle/Receiver
Model 430 (Metal Buckle) Restraint
Style Black Orange
2 pc., 5’(1524 mm) 031-3892 031-3891
2 pc., 7’(2134 mm) 031-3911 031-3912
2 pc., 9’(2743 mm) 031-3305 031-4013
1 pc., 7’(2134 mm) 031-3910 031-3887
1 pc., 9’(2743 mm) 031-3899 031-3889
Model 430P (Plastic Buckle) Restraint
Style Black Orange
2 pc., 5’(1524 mm) 031-3797 031-3917
2 pc., 7’(2134 mm) 031-3801 031-3919
1 pc., 7’(2134 mm) 031-3894 031-4011
Model 439 (Metal Buckle) Restraints, Set of Three
Style Black Orange
1 pc., 7’(2134 mm) 031-3083 031-2660

2© Ferno-Washington, Inc 234-3545-00 February 2014
Models 430, 430P, 439 Restraints
WARNING
Improper use of the restraint can cause injury. Use the
restraint only as described in this manual.
General Guidelines for Use
● For placement on a patient, follow local protocols.
● Adjust restraints to safely secure the patient to the equipment
without causing discomfort or impairing circulation.
● Keep restraints fastened when not in use to prevent
interference with equipment operation.
MODEL 430 METAL BUCKLE
● For transport in an ambulance, Ferno requires aTransport
Restraint System composed of a Ferno harness plus one
or two additional Ferno Model 430 primary, metal-buckle
restraints. See the users’ manual for the product on which
the restraint system is used for specic requirements.
● The Model 430 Series is not approved by the United States
Federal Aviation Administration for use in aircraft. Please
contact Ferno Aviation at 1.770.521.1005 for FAA-approved
patient restraints and shoulder harness assemblies.
MODEL 430P PLASTIC BUCKLE
● Secondary-use restraints are not suitable for use in a
motor vehicle.
● Secondary-userestraintsareidentiedwithalabel(Figure1).
Before Use
● Personnel who will work with the restraint need to read this
manual.
● Conrmthattherestraintoperatesproperly(SeeInspection
Checklist, page 4).
Attaching the Restraint
Attach the restraint to the equipment at points that ensure strong
anchorage and proper patient restraint. Verify restraint placement
will not interfere with use of the equipment or accessories.
Attach one-piece restraints according to local protocols.
ATTACHING TWOPIECE RESTRAINTS
1. Unbuckle the restraint and separate the straps.
2. Wrap the loop end of a strap around the selected attachment
point (Figure 2 or Figure 3).
○Model 430 may be used on ambulance cots for
transport in a motor vehicle. Do not attach to
moveable areas of equipment such as a cot drop
frame or backrest.
○Do not attach Model 430P to equipment used in a
motor vehicle.
3. Thread the male buckle/tang or female buckle/receiver
through the loop (Figures 2-3) and pull the webbing through
the loop until the loop is snug around the attachment point.
4. Repeat Steps 2 and 3 to attach the other strap to the selected
attachment point on the opposite side of the equipment.
5. Attach additional restraints following steps 1-4.
6. Conrmthatallstrapsareattachedsecurely.
REMOVING TWOPIECE RESTRAINTS
To remove the restraint from the equipment, rst unbuckle it.
Then, feed the buckles backward through the loops and remove the
restraint straps from the equipment.
1
3
2

3
© Ferno-Washington, Inc 234-3545-00 February 2014
Models 430, 430P, 439 Restraints
Buckling/Unbuckling
MODEL 430 METAL BUCKLE
To buckle the restraint, insert the male buckle/tang into the
female buckle/receiver until it locks into place (Figure 4). Always
conrmthatthebuckleissecurelyfastened.
To unbuckle the restraint (Model 430): Press the release button
in the center of the female buckle/receiver (Figure 4) and separate
the straps.
MODEL 430P PLASTIC BUCKLE
To buckle the restraint, insert the prongs of the male buckle/tang
into the female buckle/receiver until it locks into place (Figure 5).
Alwaysconrmthatthebuckleissecurelyfastened.
To unbuckle the restraint: Squeeze the outer prongs of the male
buckle/tang until they release the female buckle/receiver (Figure 5)
and separate the straps.
Adjusting the Restraint
To lengthen a strap:
1. Unbuckle the restraint.
2. Grasp the male buckle/tang and turn it perpendicular to the
webbing and pull outward, away from the strap attachment
point until the strap is the desired length (Figure 6).
To shorten a strap: Grasp the hemmed tab and pull the webbing
through the male buckle/tang until the strap is the desired length
(Figure 7).
WARNING
Improper operation can cause injury. Operate the restraint
only as described in this manual.
7
6
4
5

4© Ferno-Washington, Inc 234-3545-00 February 2014
Models 430, 430P, 439 Restraints
Limited Warranty Statement
The products sold by Ferno are covered by a limited warranty,
which is printed on the invoice you received when you purchased
the product. Please refer to the warranty terms as printed on your
invoice. The complete terms and conditions of the limited warranty,
and the limitations of liability and disclaimers, are also available
upon request by calling Ferno at 1.800.733.3766 or 1.937.382.1451.
Maintenance Schedule
The restraint requires regular maintenance. Set up and follow a
maintenance schedule. Conduct maintenance as follows:
● Inspecting: Inspect the restraint as needed, following the
Inspection Checklist below. At minimum, inspect monthly.
● Disinfecting: Disinfect the restraint after each use.
● Cleaning: Clean the restraint as needed.
Inspection Checklist
● Are all components present?
● Is restraint webbing in good condition (no cuts/frayed edges)?
● Are the buckles free of visible damage?
● Do the buckles function smoothly and properly?
● Can strap length be adjusted smoothly and properly?
If inspection indicates damage or excessive wear, take the restraint
out of service and destroy.
Disinfecting
All Models: Apply disinfectant to all restraint surfaces, following
thedisinfectantmanufacturer’sinstructionsforapplicationmethod
and contact time. Wipe with a clean cloth. Do not immerse Model
430 metal buckles in liquid.
Cleaning
MODEL 430 METAL BUCKLE
1. Remove the restraint from the equipment.
2. Metal Buckle:
○Spray the metal buckle with disinfectant, following the
disinfectantmanufacturer’sinstructionsforapplication
method and contact time. Wipe with a clean cloth. Do
not immerse in liquid.
3. Webbing:
○Add a disinfectant cleaner to warm water, following the
disinfectantmanufacturer’sinstructions.
○Immerse webbing in the solution for the time directed
by the disinfectant manufacturer. Do not immerse the
metal buckle.
○Repeatedly dip the webbing in clear water to rinse. Do
not immerse the metal buckle.
4. Hang the restraint to air-dry.
5. Attach only dry restraints to the equipment.
MODEL 430P PLASTIC BUCKLE
1. Remove the restraint from the equipment and buckle it.
2. Place the restraint inside a mesh bag (not provided) and
place it in a washing machine.
3. Launder the restraint in warm water, using a disinfectant
soap and gentle agitation. Do not use bleach.
4. Remove the restraint from the mesh bag and hang to air dry.
Do not put the restraint in a dryer.
5. Attach only dry restraints to the equipment.
Important
Metal buckles can be damaged by immersion in liquids
or by washing-machine action. Disinfect and clean
only as described in this manual.
Important
Disinfectants and cleaners containing bleach,
phenolics, or iodines can cause damage. Do not use
products containing these chemicals.
WARNING
Improper maintenance can cause injury. Maintain
the restraint only as described in this manual.
1.937.382.1451
Ferno Customer Relations
For ordering assistance or general information:
CANADA AND THE U.S.A.
Telephone (Toll-free) 1.877.733.0911
Telephone [phone]
Fax (Toll-free) 1.888.388.1349
Fax [phone]
Internet www.ferno.com
ALL OTHER LOCATIONS
For assistance or information, please contact your Ferno
distributor. If you do not have a Ferno distributor, please contact
Ferno Customer Relations:
Ferno-Washington, Inc., 70 Weil Way
Wilmington, Ohio 45177-9371, U.S.A.
Telephone [phone]
Fax [phone]
Internet www.ferno.com