Fimap BMg Sanitizer User manual

ORIGINAL INSTRUCTION DOC. 10095868 - Ver. AA - 03-2020
USE AND MAINTENANCE MANUAL
BMg
Sanitizer

CONTENTS
CONTENTS...................................................................................................................................3
GENERAL SAFETY REGULATIONS ...........................................................................................4
LOCATION OF THE MAIN MACHINE COMPONENTS .............................................................11
GENERAL DESCRIPTION .........................................................................................................12
SYMBOLS USED IN THE MANUAL ...................................................................................................................... 12
DEFINITION OF LEVELS OF WARNING .............................................................................................................. 12
PURPOSE AND CONTENT OF THE MANUAL..................................................................................................... 13
TARGET GROUP ................................................................................................................................................... 13
PRESERVATION OF THE USER........................................................................................................................... 13
ON CONSIGNMENT OF THE MACHINE .............................................................................................................. 13
INTRODUCTORY COMMENT ............................................................................................................................... 13
IDENTIFICATION DATA ......................................................................................................................................... 13
TECHNICAL DESCRIPTION.................................................................................................................................. 13
INTENDED USE..................................................................................................................................................... 13
SAFETY.................................................................................................................................................................. 13
REGULATIONS ...................................................................................................................................................... 13
SERIAL NUMBER PLATE ...................................................................................................................................... 14
TECHNICAL DATA .....................................................................................................................14
SYMBOLS AND LABELS USED ON THE MACHINE ...............................................................14
SYMBOLS USED ON THE MACHINE................................................................................................................... 14
LABELS USED ON THE MACHINE....................................................................................................................... 15
CONTROL DISPLAY .............................................................................................................................................. 16
PREPARATION OF MACHINE ...................................................................................................16
HANDLING THE PACKAGED MACHINE .............................................................................................................. 16
HOW TO UNPACK THE MACHINE ....................................................................................................................... 16
HOW TO MOVE THE MACHINE ........................................................................................................................... 17
MACHINE SAFETY................................................................................................................................................ 17
BATTERY MAINTENANCE AND DISPOSAL......................................................................................................... 17
TYPE OF BATTERY TO BE USED ........................................................................................................................ 17
INSERTING THE BATTERIES INTO THE MACHINE............................................................................................ 18
CONNECTING THE BATTERIES TO THE MACHINE SYSTEM........................................................................... 18
RECHARGING THE BATTERIES .......................................................................................................................... 18
FILLING THE SOLUTION TANK WITH WATER .................................................................................................... 19
SANITIZING SOLUTION........................................................................................................................................ 20
INSERTING WATER SYSTEM FILTER ................................................................................................................. 20
PREPARING TO WORK .............................................................................................................20
STARTING WORK ......................................................................................................................21
HOUR METER ....................................................................................................................................................... 21
BATTERY CHARGE LEVEL INDICATOR .............................................................................................................. 21
ADDITIONAL FUNCTIONS ........................................................................................................21
REVERSE FUNCTION........................................................................................................................................... 21
BUZZER ................................................................................................................................................................. 22
ALARM SCREEN ................................................................................................................................................... 22
IMMEDIATE STOP BUTTON ................................................................................................................................. 22
AT THE END OF THE WORK.....................................................................................................22
ROUTINE MAINTENANCE.........................................................................................................23
EMPTYING THE SOLUTION TANK....................................................................................................................... 23
CLEANING THE WATER SYSTEM FILTER .......................................................................................................... 23
DISPOSAL ..................................................................................................................................23
TROUBLESHOOTING ................................................................................................................24
EC DECLARATION OF CONFORMITY .....................................................................................25
3

4
GENERAL SAFETY REGULATIONS
The following symbols are used to indicate any potentially hazardous situations. Always
read this information carefully and take the necessary precautions to protect any people
and/or objects that may be present.
Operator cooperation is paramount for accident prevention. No accident prevention
programme can be e󰀨ective without the full cooperation of the person directly
responsible for the machine's operation. The majority of occupational accidents that
happen either in the workplace or whilst moving are caused by failure to respect the
most basic safety rules. An attentive, careful operator is most e󰀨ective guarantee against
accidents and is fundamental in order to implement any prevention programme.
KEEP THESE SAFETY WARNINGS WITH THE MACHINE
USER MANUAL.
DANGER: indicates an imminent dangerous situation that, unless avoided, will
result in death or serious injuries.
WARNING: Indicates a potentially dangerous situation that, unless avoided, could
cause death of serious injury.
ATTENTION: Indicates a potentially dangerous situation that, unless avoided, could
cause slight or moderate injuries.
BATTERY-POWERED MACHINE
WARNING:
• To prevent unauthorised use of the machine, the power supply must be disconnected;
switch o󰀨 the machine using the main switch (if present, remove the key from the
ignition) and disconnect the battery connector from the electrical system connector.
ATTENTION:
• The machine must only be powered with a voltage equal to that shown on the serial
number plate.
• When doing maintenance work, switch o󰀨 the machine using the main switch (if
present, remove the key from the ignition) and disconnect the battery connector from
the electrical system connector.
• To manually move electric traction versions of the machine, the electric brake must
be disengaged. Once the manual movement operations have been completed, the
electric brake must be re-engaged. Never use the machine with the electric brake
disengaged.
• If the machine needs to be pushed for maintenance purposes (batteries absent;
discharged batteries; etc.), never exceed the speed of 4 km/h.
• If lead batteries (WET) have been installed on the machine, avoid tilting the machine
beyond 30° with respect to the horizontal plane, as this could cause the highly
corrosive liquid to leak out of the batteries.

5
• Avoid contact with the battery acid.
• Keep all metal objects away from the batteries.
• Use a non-conductive device for removing the battery.
• Use a hoist and suitable equipment when lifting the batteries.
• The battery must be installed by qualied personnel.
• Always observe the safety measures of the site regarding removing the battery.
• Remove the batteries if the machine needs to be tilted in order to perform
maintenance procedures.
• The machine should not be left unattended at the end of its working cycle because
of the presence of toxic-harmful materials inside it (batteries, etc.), which are
subject to regulations regarding their disposal at special centres (see the chapter on
Scrapping).
RECHARGING THE BATTERIES
DANGER:
• If the battery charger power cable is damaged or broken, it should be replaced by the
charger manufacturer or authorised service personnel, or by another qualied person,
in order to protect against hazards.
• The socket for the battery charger cable must have a prescribed earth connection.
• Keep sparks, ames, and incandescent materials at a safe distance from the
batteries. Explosive gases are emitted during the charging phase.
• highly explosive hydrogen gas is generated while charging the batteries. Keep the
recovery tank and/or the seat mounting plate in the maintenance position during the
entire battery recharging cycle, and only perform the procedure in well-ventilated
areas at a safe distance from any open ames.
• Before charging check that the electric cable that connects the battery charger to
the batteries is not damaged, and if it is damaged do not use it and contact technical
assistance.
• Before charging check that the electric cable that connects the battery charger to
the mains is not damaged, and if it is damaged do not use it and contact technical
assistance.
• Before starting to charge the batteries in versions with on-board battery charger,
check there is no stagnant water or humidity in the battery charger socket.
• Do not disconnect the direct current cable of the battery charger from the socket
of the machine when the battery charger is operating. This is necessary to prevent
electric arcs forming. To disconnect the battery charger when charging, rst
disconnect the power cable from the mains socket.
WARNING:
• Do not use incompatible battery chargers since they could damage the batteries and
potentially cause a re.
• Before using the battery charger, make sure that the frequency and the voltage
indicated on the battery charger serial number plate or in the charger user manual in
versions with on-board battery charger (enclosed with the machine documentation)
match the mains voltage.

6
• Keep the battery charger's cable at a safe distance from any hot surfaces.
• Never smoke in the machine's vicinity while the batteries are charging.
• Carefully read the user manual of the battery charger you want to use before
recharging.
USING THE MACHINE
DANGER:
• In case of danger, act promptly by pressing the emergency button (if present) or
disconnecting the battery connector from the electrical system connector.
• If the machine is used in dangerous areas (e.g. petrol stations), the relative safety
standards must be observed. It is forbidden to use the machine in environments with
a potentially explosive atmosphere.
WARNING:
• The machine must be exclusively used by authorised, trained personnel.
• Always use the machine in compliance with its intended use, taking into consideration
local conditions and looking out for the presence of others when working, especially
children.
• This machine should not be used by persons (including children) with physical,
sensorial or mental impairments and by persons with little experience and/or little
knowledge of the machine itself.
• Do not use the machine on surfaces with a slope greater than the one indicated on
the serial number plate.
• The machine cannot be used on uneven or bumpy oors. Do not use the machine on
slopes.
• In the event of a re, use a powder extinguisher. Do not use water.
• Adapt the speed to the adhesion conditions.
• Do not use the machine if you do not have the requisite knowledge or authorisation.
• Do not use the machine if these safety warnings and the machine user manual have
not been read and understood.
• Do not use the machine under the inuence of alcohol or drugs.
• Do not use the machine when using a mobile phone or other types of electronic
devices.
• Do not use the machine if it is not working correctly.
• Do not use the machine in areas where there are inammable vapours or liquids or
combustible powders.
• Do not use the machine in areas where it is too dark to see the controls or operate
the machine safely, unless the work lights or the front headlights are on (if present).

7
ATTENTION:
• Children must be supervised to ensure they do not play with the machine.
• During the working of the machine, pay attention to other people and especially to
children.
• Read the labels on the machine carefully. Do not cover them for any reason, and
replace them immediately if they become damaged.
• The machine must only be used and stored in an enclosed or covered environment.
• The machine must not be used or stored outdoors in damp conditions or directly
exposed to rain.
• The machine does not cause harmful vibrations.
• Only use the machine in accordance with the instructions set out in these safety
warnings and in the machine user manual.
• Reduce speed on slopes and dangerous corners.
• Always follow the instructions for mixing, use and disposal on the containers of the
chemical substances.
• Always take appropriate measures to protect any individuals and/or objects that may
be present while using this machine.
• Be careful to avoid collisions with shelving or sca󰀨olding, above all if there is a risk of
objects falling from heights.
• Do not place any liquid containers on the machine.
• The machine must only be used in temperatures ranging from +10 °C to +40 °C. The
humidity level must be between 30% and 95%.
• When using disinfectants to sanitize areas, always follow the instructions and respect
the warnings indicated on the container labels.
• Before handing disinfectants for sanitizing areas, operators are advised to put on the
appropriate PPE (Personal Protective Equipment), suitable for the work to be carried
out.
• In the event of a re, use a powder re extinguisher if possible, and avoid the use of
water.
• Do not allow any objects to penetrate into the machine's openings. Do not use the
machine is the openings are obstructed.
• Keep the machine's openings free of any dust, lint, hairs, or any other foreign
materials that could reduce the airow.
• Do not remove or alter any labels a󰀩xed to the machine.
• This machine has not been made for external use but internal locations only.
• Before starting to work check that there are no leaks.
• Before starting to work check that all the safety devices have been installed and are
working correctly.
• Take all due precautions so that hair, jewellery, loose clothing do not get entangled in
the machine's moving parts.
• Only use the machine in well-lit areas.

8
DEACTIVATION OF THE MACHINE
WARNING:
• Always protect the machine against sunlight, rain, and other atmospheric agents,
both while it is stationary and while it is in function. Store the machine in a dry,
sheltered place: this machine is only designed for use under dry conditions, and must
not be used or stored outdoors under humid conditions.
• Do not park the machine near combustible materials, powders, gases or liquids.
• Stop the machine on a at surface.
• If the machine is left unattended, it must be protected from any accidental movements
ATTENTION:
• The machine must only be stored in temperatures ranging from +10 °C to +40 °C.
The humidity level must be between 30% and 95%.
MAINTENANCE
DANGER:
• In order to avoid short-circuits when working in the vicinity of electrical components,
do the following: avoid the use of non-insulated tools; do not place or allow metallic
objects to fall upon the electrically powered components; remove any rings, watches
and/or clothing with metallic parts that might come into contact with the electrically
powered components.
• do not work underneath the raised machine without adequate xed safety supports.
WARNING:
• The cleaning and maintenance to be carried out by the user must not be performed
by unsupervised children.
• Read all the relevant instructions carefully before performing any maintenance/repair
operations.
• If the machine does not work properly, check this is not caused by failure to carry out
maintenance. Otherwise, ask for intervention of the authorised technical assistance
centre.
• Restore all electrical connections after any maintenance interventions.
ATTENTION:
• Avoid contact with moving parts. Do not wear loose clothing or jewellery and tie long
hair back.
• Block the wheels before lifting the machine.

9
• Lift the machine with equipment that can sustain the weight to be lifted.
• Never tamper with the machine's protection devices for any reason; always follow the
supplied routine maintenance instructions scrupulously.
• If any parts need to be replaced, always request ORIGINAL spare parts from an
authorized Dealer or Retailer.
• In order to ensure the machine's safety and proper functionality, always have the
scheduled maintenance interventions (specied in the appropriate section of this
Manual) performed by authorized personnel or by an authorized Service Centre.
• Do not wash the machine with direct jets of water, pressurised water or with corrosive
substances, and do not wet it in the vicinity of electrical components.
• Have the machine checked by an authorised technical assistance centre every year.
• When disposing of consumable materials, observe the laws and regulations in force.
Once the machine has reached the end of its service life, the materials contained
within it must be disposed of in an appropriate manner, keeping in mind that the
machine itself has been built using fully recyclable materials.
• All repairs must be carried out by qualied personnel.
• Do not physically change the design characteristics of the machine.
• Use spare parts provided by authorised service centres.
• Wear personal protective equipment as required and as suggested in the manual.
TRANSPORT
WARNING:
• Drain both tanks before transport.
• Use a ramp, a truck or a trailer that can support the weight of the machine and the
operator.
• The ramp for placing the machine on the transport vehicle should have such a slope
that the machine does not get damaged.
• Secure the device according to the directives in force in the country of use, so that it
cannot slide or tip over when being transported.
• In versions with electric traction, make sure the electric brake is correctly engaged
after loading the machine onto the transport vehicle.
ATTENTION:
• Use caution when moving the machine under temperatures below freezing. The water
contained in the water recovery tank or in the pipes could freeze, and could seriously
damage the machine itself.

10
RIDE-ON MACHINES
WARNING:
• Do not use the machine in areas where there is a risk of falling objects, unless the
machine is equipped with an overhead guard (optional).
• To place the machine on the transport vehicle use a pulley. Do not drive the machine
on or o󰀨 a truck or trailer.
• Engage the parking brake after loading the machine onto the transport vehicle.
ATTENTION:
• Reduce speed before making a turn.
• Keep all parts of your body inside when the machine is moving.
• Be careful when reversing.
• Do not transport passengers. Do not use the machine as a means of transport.
• If the machine is to be used in the presence of other individuals, aside from the
operator, the beacon light (optional) must be utilized.
• This machine has not been approved for use on public streets or roadways.
• Do not push or tow the machine without an operator on the seat who can control the
machine.
• Before starting work check that the brakes and steering are working correctly.
• Before starting work adjust the seat and steering wheel, and also the seat belt if there
is one.

LOCATION OF THE MAIN MACHINE COMPONENTS
The machine's main components are the following:
1. Front working lights.
2. Blinking light.
3. Recovery tank rotation stop lever.
4. Emergency button.
5. Object holder net.
6. Recovery tank lid.
7. Recovery tank.
8. Tail lights.
9. Operator's seat.
10. Sanitizing solution tank.
11. Command display.
12. Horn button.
13. Spray kit control button.
14. Steering wheel.
15. Reverse gear selection lever.
16. Sanitizing solution lter.
17. Drive pedal.
18. Main key switch.
19. Sanitizing solution adjustment knob.
20. Sanitizing solution tank level hose.
21. Sanitizing solution tank rapid lling hose.
22. Sanitizing solution tank dosing cap.
23. Spray nozzle.
24. Electric brake control lever.
11
9
7
8
10
6
2
3
5
4
1
15
17
14
13
12
16
11
18
23
19
24
20
21 22

The descriptions contained in this document are not binding. The company therefore reserves the right to make any modications at any time to
elements, details, or accessory supply, as considered necessary for reasons of improvement or manufacturing/commercial requirements. The
reproduction, even partial, of the text and drawings contained in this document is prohibited by law. The company reserves the right to make
any technical and/or supply modications. The images are shown as reference only and are not binding as to the actual design and/or
equipment.
SYMBOLS USED IN THE MANUAL
GENERAL DESCRIPTION
Open book symbol with an "i":
Indicates the need to consult the instruction manual.
Open book symbol:
Tells the operator to read the user manual before using the device.
Covered place symbol:
The operations preceded by this symbol must always be carried out in a dry, covered area.
Information symbol:
Indicates additional information for the operator, to improve the use of the device.
Warning symbol:
Carefully read the sections preceded by this symbol meticulously following the instructions indicated for the safety of the operator
and the device.
Danger symbol (corrosive substances):
The operator should always wear protective gloves to avoid the risk of serious injury to the hands caused by corrosive substances.
Danger symbol (battery acid leakage):
Indicates the danger of leaking acid or acid fumes from the batteries while they are being recharged.
Danger symbol (moving carriages):
Indicates that the packed product should be handled with suitable carriages that conform to legal requirements.
Mandatory room ventilation symbol:
Informs the operator that the room must be ventilated while the batteries are being recharged.
Symbol indicating the compulsory use of protective gloves:
Indicates that the operator should always wear protective gloves, to avoid the risk of serious injury to his hands from sharp objects.
Symbol indicating the compulsory use of tools:
Informs the operator of the need to use tools not included with the machine.
Symbol indicating a treading ban:
Informs the operator that it is forbidden to tread on machine components, as this could lead to serious injury.
Recycling symbol:
Tells the operator to carry out the operations in compliance with environmental regulations in force in the place where the appliance
is being used.
Disposal symbol:
Carefully read the sections marked with this symbol for disposing of the appliance.
DEFINITION OF LEVELS OF WARNING
DANGER: indicates an imminent dangerous situation that, unless avoided, will result in death or serious injuries.
WARNING: Indicates a potentially dangerous situation that, unless avoided, could cause death of serious injury.
ATTENTION: Indicates a potentially dangerous situation that, unless avoided, could cause slight or moderate injuries.
N.B.: instructs the reader to pay particular attention to the topic that follows.
12

PURPOSE AND CONTENT OF THE MANUAL
The aim of this manual is to provide customers with all the information needed to use the machine in the safest, most appropriate and most
autonomous way. This includes information concerning technical aspects, safety, operation, downtime, maintenance, spare parts and scrapping.
The operators and qualied technicians must carefully read the instructions in this manual before carrying out any operations on the machine.
If in doubt about the correct interpretation of instructions, contact your nearest FIMAP Customer Service Centre to obtain the necessary
clarications.
TARGET GROUP
This manual is written both for operators and for qualied machine maintenance technicians. Operators must not perform operations that should
be carried out by qualied technicians. The manufacturer is not liable for damages resulting from failure to comply with this veto.
PRESERVATION OF THE USER
The USE AND MAINTENANCE MANUAL must be stored in its special pouch close to the machine, protected from liquids and anything else that
could compromise its legibility.
ON CONSIGNMENT OF THE MACHINE
When the machine is consigned to the customer, an immediate check must be performed to ensure all the material mentioned in the shipping
documents has been received, and also to check the machine has not su󰀨ered damage during transportation. If this is the case, the carrier
must ascertain the extent of the damage at once, informing our customer service o󰀩ce. It is only by prompt action of this type that the missing
material can be obtained, and compensation for damage successfully claimed.
INTRODUCTORY COMMENT
Any machine can only work properly and e󰀨ectively if used correctly and kept in full working order by carrying out the maintenance operations
described in the attached documentation. We therefore suggest you read this instruction booklet carefully and read it again whenever di󰀩culties
arise while using the machine. If necessary, remember that our assistance service (organised in collaboration with our dealers) is always
available for advice or direct intervention.
IDENTIFICATION DATA
For technical assistance or to request replacement parts, always give the model, the version and the serial number (written on the relevant
plate).
TECHNICAL DESCRIPTION
The BMg Sanitizer is a machine designed for the sanitization of oors which sprays special sanitizing products in areas with heavy footfall, thus
reducing the presence of pathogenic material as it moves forwards. The machine must only be used for this purpose.
INTENDED USE
This machine is designed and built for sanitizing oors in commercial, civil and industrial environments, in proven safety conditions, and must be
used by a qualied operator. The machine is only suitable for use in closed (or at least covered) places.
ATTENTION: the machine is not suitable for use in the rain, or under water jets.
SAFETY
Operator cooperation is paramount for accident prevention. No accident prevention programme can be e󰀨ective without the full cooperation
of the person directly responsible for machine operation. The majority of occupational accidents that happen either in the workplace or whilst
moving are caused by failure to respect the most basic safety rules. An attentive, careful operator is most e󰀨ective guarantee against accidents
and is fundamental in order to implement any prevention programme.
REGULATIONS
All references to forwards and backwards, front and rear, right and left indicated in this manual should be understood as referring to the operator
in a driving position with his hands on the steering wheel.
13

SERIAL NUMBER PLATE
11
10
9
8
7
6
1
2
3
4
5
The serial number plate is located at the rear of the steering column, and indicates the
machine's general characteristics, including its serial number. The serial number is a very
important piece of information and should always be provided together with any request for
assistance or when purchasing spare parts. The serial number plate contains the following:
1) The weight of the batteries that power the machine (expressed in kg). See paragraph “TYPE
OF BATTERY TO BE USED” on page 17.
2) The IP protection rating of the machine.
3) The gross weight of the machine (expressed in kg).
4) The machine ID code.
5) The machine serial number.
6) The machine ID name.
7) The nominal power consumed by the machine (expressed in W).
8) The maximum slope that the appliance can handle during work activities (expressed as %).
9) The year of machine manufacture.
10) The nominal voltage of the machine (expressed in V).
11) The commercial name of the machine, and the manufacturer's address.
TECHNICAL DATA
TECHNICAL DATA U/M
[KMS]
BMG
SANITIZER
Rated machine power kW 0,65
Minimum transport width mm 630
Traction motor electrical properties (voltage - power) V / W 24 - 300
Compressor electrical properties (voltage - power) V / W 24 - 350
Maximum slope during work with GVW % 17
Maximum speed during transport km/h 5,5
Recommended speed during work km/h 2,8
Maximum solution tank capacity l 51
Minimum inversion footprint mm 1830
Machine dimensions (length - height - width) mm
1285
1189
630
Battery compartment dimensions (length - height - width) mm
350
190
310
Machine weight when empty kg 128
Transported machine weight kg 210
GVW kg 336
Sound pressure level in operator seat [ISO 11201] (LpA) dB <70
Uncertainty KpA dB 1,5
Hand-arm vibrations [IEC 60335-2-72; IEC 62885-9; ISO 5349-1] m/s2<2,5
Whole body vibrations [IEC 60335-2-72; IEC 62885-9; ISO 2631-1] m/s20,65
Vibration measurement uncertainty 4%
SYMBOLS USED ON THE MACHINE
Filter body position symbol:
Applied to the front of the machine to indicate the position of the solution tank lter.
RReverse gear activation/deactivation lever position symbol:
Applied to the reverse gear activation/deactivation lever.
SYMBOLS AND LABELS USED ON THE MACHINE
14

LABELS USED ON THE MACHINE
Main switch symbol:
Applied to the control panel, positioned on the front of the machine, to indicate the main switch.
Label indicating sanitizing solution tap control:
Applied in the vicinity of the steering column to identify the sanitizing solution tap control lever.
Label indicating the need to read the Use and Maintenance Manual:
Applied in the vicinity of the steering column in order to remind the operator to read the user and maintenance manual before
using the machine.
Warning label to read the user manual of the battery charger (versions with Battery charger):
Applied in the vicinity of the steering column indicating to read the user manual of the battery charger. Also indicates to pay
attention to when to perform the charging cycle and how long it should last.
Battery charging sequence label (versions without Battery Charger):
Located near the steering column, indicating the sequence to perform to recharge the batteries correctly.
Visible daily maintenance label:
Applied near the steering column, indicating to tighten the machine's water tap after every work cycle and to clean the lters and
the squeegee.
Warning label during battery charging:
Located near the steering column, listing the warnings to perform when recharging the batteries.
Water system lter maintenance label:
Applied near the water system lter to remind the user to clean it after each work cycle.
Label warning about the risk of crushed hands:
Indicates danger to hands due to crushing between two surfaces.
Acoustic signalling device control label:
Applied in the vicinity of the steering column to indicate the acoustic signalling device's control button.
Symbol for maximum temperature for lling the solution tank:
Applied to the left-hand side of the machine's solution tank to indicate the maximum temperature of the water that can be used to
safely ll the solution tank.
Solution tank lling symbol:
Located on the left side of the machine's solution tank to indicate the amount of sanitizing solution in the tank. The symbol on the
side indicates that the tank is full to about a quarter of its capacity.
Solution tank lling symbol:
Located on the left side of the machine's solution tank to indicate the amount of sanitizing solution in the tank. The symbol on the
side indicates that the tank is full to about a half of its capacity.
Solution tank lling symbol:
Located on the left side of the machine's solution tank to indicate the amount of sanitizing solution in the tank. The symbol on the
side indicates that the tank is full to about three-quarters of its capacity.
Solution tank lling symbol:
Located on the left side of the machine's solution tank to indicate the amount of sanitizing solution in the tank. The symbol on the
side indicates that the tank is full.
15

CONTROL DISPLAY
5
1
2
3
4
The control display is divided in:
1) Battery charge level symbol, see paragraph “BATTERY CHARGE LEVEL INDICATOR” on page
21.
2) Machine hours of use (expressed in a numerical value), see paragraph “HOUR METER” on page
21.
3) Battery charge percentage (expressed in a numerical value, see paragraph “BATTERY CHARGE
LEVEL INDICATOR” on page 21.
4) Hourglass symbol which refers to the machine's hour meter, see paragraph “HOUR METER” on page 21.
Forward speed level of the machine.
PREPARATION OF MACHINE
HANDLING THE PACKAGED MACHINE
The machine's overall weight including packaging is 173Kg. The external dimensions of the package are: width 750mm; length 1460mm and
height 1385mm.
N.B.: it is recommended that all the packaging components be kept for any future machine transportation.
DANGER: Move the packaged product with handling equipment that complies with legal requirements regarding size and mass of the
packaging.
HOW TO UNPACK THE MACHINE
The machine is shipped in specic packaging. To remove it, proceed as follows:
1. Place the lower part of the outer packaging in contact with the oor.
N.B.: use the pictograms printed on the box as a reference.
2. Remove the outer package.
WARNING: the machine is contained in specic packaging materials, whose elements (plastic bags, staples, etc.) can pose potential
hazards, and must not be left within reach of children, disabled persons, etc.
ATTENTION: It is recommended to wear the appropriate PPE (Personal Protective Equipment), suitable for the work to be carried out.
3. Insert a ramp in the rear part of the machine.
ATTENTION: the ramp gradient must not be such as to cause damage to the machine as it comes down.
4. The machine is xed to the pallet with wedges (1) that block the wheels (Fig.1). Remove these wedges.
5. Move to the right rear part of the machine and check that the electro-brake, present in the traction gear motor, is not engaged. Turn the lever
(2) clockwise (Fig.2).
6. Drive the machine down the ramp.
ATTENTION: during this operation, check there are no people or objects near the machine.
16
15 1614
12 13 14
8 8
11
13
12
10 8
11
10
9
9
7
7 8
5 6
21 1
2
6
45
33
35
4

HOW TO MOVE THE MACHINE
To transport the machine safely, proceed as follows:
DANGER: before starting any task, make sure the current regulations concerning the safe transport of dangerous substances are
scrupulously observed.
1. Make sure the solution tank is empty. If it isn't, empty it completely. See paragraph “EMPTYING THE SOLUTION TANK” on page 23.
2. Sit on the driver’s seat.
3. Insert the key (3) into the main switch on the control panel. Move the main switch to position "I" (Fig.3) by turning the key a quarter turn
clockwise.
4. Press the drive pedal (4) (Fig.4) to begin moving the machine.
5. Use a ramp to move the machine up onto the transport vehicle.
ATTENTION: during this operation, check there are no people or objects near the machine.
N.B.: the ramp gradient must not be such as to cause damage to the machine as it goes up.
6. Position the machine on the means of transport, and set the main switch to “0” by turning the key (3) a quarter turn anti-clockwise (Fig.5).
Remove the key from the instrument panel.
7. Get o󰀨 the machine.
8. Press the recovery tank release lever (5) and turn the recovery tank into the maintenance position (Fig. 6).
ATTENTION: the following operations must be carried out by qualied personnel. An incorrect connection of the connector may cause a
malfunction of the device.
9. Disconnect the electrical connector from the machine's general system.
10. Rotate the recovery tank into the work position. Make sure that the recovery tank retainer system is correctly engaged.
WARNING: secure the device according to the directives in force in the country of use, so that it cannot slide or tip over.
MACHINE SAFETY
To ensure that work is carried out in the best safety conditions, proceed as follows:
1. Take the machine to the maintenance area.
WARNING: The place designated for this operation must comply with current regulations concerning safety at work and current
environmental protection regulations.
2. Make sure the solution tank is empty. If it isn't, empty it completely. See paragraph “EMPTYING THE SOLUTION TANK” on page 23.
3. Bring the main switch to the "0" position by turning the key (3) a quarter turn anti-clockwise (Fig.5). Remove the key from the instrument
panel.
4. Get o󰀨 the machine.
5. Press the recovery tank release lever (5) and turn the recovery tank into the maintenance position (Fig. 6).
6. Disconnect the general system connector from the battery connector.
WARNING: It is recommended that all electrical disconnection operations be carried out by expert personnel, trained at the specialised
assistance centre.
7. Rotate the recovery tank into the work position. Make sure that the recovery tank retainer system is correctly engaged (Fig. 8).
BATTERY MAINTENANCE AND DISPOSAL
For battery maintenance and recharging, respect the instructions provided by the battery manufacturer. When the batteries reach the end of
their service life, they must be disconnected by a specialised and properly trained operator, and must be subsequently removed from the battery
compartment using suitable lifting devices.
N.B.: Dead batteries are classied as dangerous waste and as such must be delivered to an authorised body for disposal.
TYPE OF BATTERY TO BE USED
CODE DESCRIPTION
410875 TP BATTERY 12V 110Ah (ACID)
410877 MFP BATTERY 12V 105Ah (GEL)
Used batteries must meet the requirements set out in DIN EN 50272-3 "Traction batteries for
industrial trucks".
To ensure proper performance, the machine must be powered with 24V.
The machine can be powered with the batteries listed in the table to the side.
N.B.: The use of two 12TP110 batteries is recommended.
17

INSERTING THE BATTERIES INTO THE MACHINE
The batteries must be housed in the special compartment inside the machine and should be handled using lifting equipment that is suitable both
regard to the weight and the coupling system used.
ATTENTION: It is recommended to wear the appropriate PPE (Personal Protective Equipment), suitable for the work to be carried out.
ATTENTION: to prevent an accidental short circuit use insulated tools to connect the batteries, and do not place or drop metal objects on
the battery. Remove rings, watches and any clothing with metal parts that may come into contact with the battery terminals.
The various phases for inserting the batteries in the battery compartment are as follows:
1. Carry out the steps necessary to secure the machine, see paragraph “MACHINE SAFETY” on page 17.
2. Press the recovery tank release lever (5), turn the recovery tank into the maintenance position (Fig. 6) and turn the recovery tank as far as it
will go.
N.B.: for battery maintenance and daily recharging, you must fully respect the indications provided by the manufacturer or retailer.
ATTENTION: all installation and maintenance operations must be carried out by specialised personnel.
N.B.: before installing the battery, clean the battery compartment.
N.B.: Check that the connectors on the cables supplied are functioning correctly.
ATTENTION: check that the characteristics of the battery that you are looking to use are appropriate for the type of work to be performed.
ATTENTION: Check the battery charge and the condition of the contacts on the battery.
N.B.: you are advised to only lift and move the batteries with lifting and transportation means suitable for the specic weight and size
ATTENTION: the lifting hooks must not damage the blocks, connectors or cables.
N.B.: Before inserting the batteries into the machine, remember to cover the terminals with a little grease to protect them against external
corrosion.
3. House the batteries in the compartment, positioning the poles “+” and “-“ opposite each other.
CONNECTING THE BATTERIES TO THE MACHINE SYSTEM
WARNING: The batteries should be connected so as to obtain a total voltage of 24V.
WARNING: It is recommended that all installation and maintenance operations be carried out by expert personnel, trained at the
specialised assistance centre.
WARNING: to prevent an accidental short circuit use insulated tools to connect the batteries, and do not place or drop metal objects on
the battery. Remove rings, watches and any clothing with metal parts that may come into contact with the battery terminals.
The various phases for inserting the batteries in the battery compartment are as follows:
1. Using the jumper cable supplied with the machine, connect the batteries to the “+” and “-” poles in series.
2. Connect the battery connector cable to the "+" and "-" poles in order to obtain the terminal voltage of 24V.
3. Connect the electrical system connector to the battery connector.
RECHARGING THE BATTERIES
The batteries must be charged prior to rst use, and whenever they no longer provide su󰀩cient power to perform the desired work.
ATTENTION: The control board and the battery charger, if present on-board, are set for lead - acid batteries, contact the nearest FIMAP
assistance centre to modify the setting if you want to use gel batteries.
ATTENTION: to avoid any permanent damage to the batteries, it is essential to avoid their complete discharge; begin recharging them
within a few minutes of noting the "discharged batteries" signal.
ATTENTION: Never leave the batteries completely discharged, even if the machine is not being used.
1. Bring the machine to the battery recharging area.
18

ATTENTION: park the machine in an enclosed place, on a at and level surface; near the machine there must be no objects that could
either damage it, or be damaged through contact with it.
DANGER: the room used to recharge the batteries must be adequately ventilated to prevent the accumulation of gases that leak from
batteries.
2. Carry out the steps necessary to secure the machine, see paragraph “MACHINE SAFETY” on page 17.
3. Press the recovery tank release lever (5) and turn the recovery tank into the maintenance position (Fig. 6).
To recharge the batteries without the built-in battery charger, proceed as follows:
WARNING: It is recommended that all installation and maintenance operations be carried out by expert personnel, trained at the
specialised assistance centre.
• Disconnect the electric system connector from the battery connector.
• Connect the external battery charger cable to the battery connector.
N.B.: the coupling connector of the battery charger is consigned inside the bag containing this instruction booklet, and must be
assembled on the cables of the battery charger as indicated in the instructions.
DANGER: before connecting the batteries to the battery charger, make sure it is suitable for the batteries used.
N.B.: carefully read the use and maintenance instructions of the battery charger that is used for charging.
• Rotate the recovery tank until the foot (6) on the gas spring is resting on the solution tank (Fig.8).
ATTENTION: keep the recovery tank open for the duration of the battery recharging cycle to allow gas fumes to escape.
• Once the recharge cycle has been completed, rotate the recovery tank to the maintenance position
and disconnect the battery charger's cable from the battery connector.
• Connect the electrical system connector to the battery connector.
• Rotate the recovery tank into the work position. Make sure that the recovery tank retainer system is correctly engaged (Fig. 8).
To recharge the batteries with the on-board battery charger proceed as follows:
WARNING: It is recommended that all installation and maintenance operations be carried out by expert personnel, trained at the
specialised assistance centre.
N.B.: Carefully read the use and maintenance instructions of the battery charger that is used for charging, this document is delivered
along with the machine.
• Rotate the recovery tank until the foot (6) on the gas spring is resting on the solution tank (Fig.8).
• Remove the cap (7) from the battery charger socket (Fig.9).
ATTENTION: before connecting the batteries to the battery charger, make sure it is suitable for the batteries used.
WARNING: Before inserting the battery charger power cable into the socket, verify that there is no condensate or other forms of liquids.
N.B.: the battery charger power cable is delivered inside the bag containing this instruction booklet.
• Plug the battery charger cable into the mains socket.
• Connect the battery charger's power cable to the socket on the battery charger itself.
ATTENTION: keep the recovery tank open for the duration of the battery recharging cycle to allow gas fumes to escape.
• When the recharge cycle is complete, disconnect the battery charger cable from the mains.
• Disconnect the battery charger's power cable from the socket on the battery charger itself.
• Reposition the cap (7) in the socket of the battery charger (Fig.9).
• Rotate the recovery tank into the work position. Make sure that the recovery tank retainer system is correctly engaged (Fig. 8).
FILLING THE SOLUTION TANK WITH WATER
Before lling the solution tank, carry out the following steps:
1. Take the machine to the usual place for lling the solution tank.
2. Carry out the steps necessary to secure the machine, see paragraph “MACHINE SAFETY” on page 17.
3. Move to the front of the machine and check that the water system lter cap (8) is tightened, otherwise tighten it (Fig.10).
19

SANITIZING SOLUTION
After lling the solution tank with clean water, add the sanitizing chemical product to the tank in the concentration and manner indicated on the
sanitizing product manufacturer's label.
ATTENTION: It is recommended to wear the appropriate PPE (Personal Protective Equipment), suitable for the work to be carried out.
The solution tank can be lled with water in two di󰀨erent ways:
• Removing the cap/measuring device (9) and lling the solution tank by means of a rubber hose or a bucket (Fig.11).
• Using the ller hose (10) (Fig.12), which supports the water hose on its own. In this case, be sure to remove the cap/measuring device (9) in
order to allow the air to vent properly.
4. Fill with clean water, at a temperature no higher than 50°C (122°F) and no lower than 10°C (50°F). The amount inside the tank can be seen
by means of the level tube (11) on the left-hand side of the machine (Fig.13).
INSERTING WATER SYSTEM FILTER
Before using the machine for the rst time the water system lter needs to be reset, for shipping reasons the lter cartridge and the cap have
been removed. To insert the lter cartridge in the water system lter body proceed as follows:
1. Take the machine to the maintenance area.
2. Carry out the steps necessary to secure the machine, see paragraph “MACHINE SAFETY” on page 17.
ATTENTION: It is recommended to wear the appropriate PPE (Personal Protective Equipment), suitable for the work to be carried out.
3. Close the tap's output ow, and shift the knob (12) on the left hand side of the steering column (Fig.14) downward.
4. Move to the front of the machine, insert the lter cartridge (13) in the housing on the cap (8) (Fig.15).
N.B.: The O-ring gasket in the lter cartridge should be inserted into its seat in the cap.
5. Screw the cap (8) onto the body of the sanitizing solution lter (14) (Fig.16).
PREPARING TO WORK
Before beginning to work, it is necessary to:
1. Check that the quantity of sanitizing solution in the solution tank is correct for the type of work to be carried out; if not, rell the solution tank.
See paragraph “FILLING THE SOLUTION TANK WITH WATER” on page 19and paragraph “SANITIZING SOLUTION” on page 20.
2. Check that the main switch is set to “0", turn the key (1) a quarter turn anti-clockwise (Fig.1) . With the machine o󰀨, remove the key from the
instrument panel.
3. Press the recovery tank release lever (2) and turn the recovery tank into the maintenance position (Fig. 2).
WARNING: It is recommended that all installation and maintenance operations be carried out by expert personnel, trained at the
specialised assistance centre.
4. Connect the battery connector to the machine's general system connector.
5. Rotate the recovery tank into the work position. Make sure that the recovery tank retainer system is correctly engaged (Fig. 3).
6. Move to the right rear part of the machine and check that the electro-brake in the traction gear motor is engaged, turn the lever (3) clockwise
(Fig. 4).
7. Move to the front of the machine and check that the water system lter cap (4) is closed, otherwise tighten it (Fig.5).
8. Move to the front left part of the machine and check that the water tap is opened completely, turn the knob (5) upwards (Fig.6).
20
6
5
54 4
3
1132 2 2