Fimap FSR User manual

WORKSHOP HANDBOOK
FSR
Version: AA
Date: February 11, 2014
Document Number: 10046657

Contents
I Product Introduction 5
1 Serial Number and Technical Support 6
1.1 The Serial Tag ................................. 6
1.2 Serial Tag location ............................... 6
2 Main Technical Features 7
II Anomalies Resolution Guide 9
3 Trouble-shooting for the most common anomalies 10
3.1 Electrical system: what to do if. . . ...................... 10
3.2 Main broom system: what to do if. . . .................... 13
3.3 Side broom system: what to do if. . . .................... 14
3.4 Vacuum system: what to do if. . . ...................... 15
3.5 Frame and traction system: what to do if. . . ................ 16
3.6 Endothermic Engine: what to do if. . . ................... 17
4 Disassembling Procedures 18
4.1 Electrical Installation ............................. 19
4.2 Main Broom System .............................. 23
4.3 Side Broom System .............................. 26
4.4 Vacuum System ................................ 28
4.5 Frame and Traction System ......................... 30
4.6 Endothermic Engine System ......................... 33
III Machine Description 35
5 Electrical System 36
5.1 Structure .................................... 36
5.2 Description ................................... 37
5.3 Adjustments .................................. 49
5.4 Maintenance and Checks ........................... 51
5.5 Alarm Table ................................... 52
5.6 Menu tables ................................... 53
5.7 Technical Features ............................... 59
5.8 Recommended Spare Parts .......................... 59
2

6 Main Sweeping System 60
6.1 Structure .................................... 60
6.2 Description ................................... 60
6.3 Adjustments .................................. 61
6.4 Maintenance and checks ........................... 61
6.5 Technical Features ............................... 63
6.6 Consumable Spare Parts ........................... 63
6.7 Recommended Spare Parts .......................... 63
7 Side Brush System 64
7.1 Structure .................................... 64
7.2 Description ................................... 64
7.3 Adjustment ................................... 65
7.4 Maintenance and checks ........................... 66
7.5 Technical Features ............................... 67
7.6 Consumable Spare Parts ........................... 67
7.7 Recommended Spare Parts .......................... 67
8 Vacuum System 68
8.1 Structure .................................... 68
8.2 Description ................................... 68
8.3 Adjustments .................................. 70
8.4 Maintenance and Checks ........................... 70
8.5 Technical Features ............................... 72
8.6 Consumable Spare Parts ........................... 72
8.7 Recommended Spare Parts .......................... 72
9 Collection System 73
9.1 Structure .................................... 73
9.2 Description ................................... 73
9.3 Maintenance and Checks ........................... 74
9.4 Technical Features ............................... 75
9.5 Consumable Spare Parts ........................... 75
10 Machine Frame and Traction System 76
10.1Structure .................................... 76
10.2Description ................................... 76
10.3Adjustments .................................. 77
10.4Maintenance and Checks ........................... 77
10.5Technical Features ............................... 80
10.6Consumable spare parts ........................... 80
10.7Recommended Spare Parts .......................... 80
11 Endothermic engine (FSR Hybrid) 81
11.1Structure .................................... 81
11.2Description ................................... 81
11.3Operation of the Hybrid Model ........................ 82
11.4Endothermic Engine .............................. 84
11.5Maintenance and Checks ........................... 85

11.6Warnings .................................... 87
11.7Technical Features ............................... 88
IV Accessories and Add-On 89
12 Accessories 90
12.1Accessories List ................................ 90
12.2Blinking Kit - 223421 ............................. 90
12.3Onboard Charger Kit (only FSR B) - 223390 ................ 92

Part I
Product Introduction
5

1-6
Chapter 1
Serial Number and Technical Support
1.1 The Serial Tag
1.2 Serial Tag location
To have access to the Serial Tag is necessary to open the glove box on the steering
column. The Serial Number is an extremely important information which has to
be provided each time a Technical Support is required or is necessary to buy spare
parts or accessories. The serial number is the only way to identify the machine by
model, production date type equipments in general.
6

2-7
Chapter 2
Main Technical Features
Technical Data
TECHNICAL DESCRIPTION U/M FSR B FSR Hybrid
Working Width (without side brush) mm 580 580
Working Width (with side brush) mm 790 790
Working Width (with double side brush) mm 1000 1000
Working capacity, up to m2
h4500 4500
Steering Diameter mm 3600 3600
Total Power W 1250 1250
Maximum Ramp Gradient % 10 10
Machine length mm 1455 1455
Machine Width (without side brush) mm 845 845
Machine Width (with side brush) mm 920 920
Machine Width (with double side brush) mm 1000 1000
Machine Height mm 1030 1030
Machine Height (with optional blinking kit) mm 1080 1080
Wheel Base mm 700 700
Wheel Track mm 720 720
Footrest height from the ground mm 236 236
Seat height from the footrest mm 503 503
Sound pressure level (ISO 11201) LpA dB (A) 60.5 81.2
Sound power level (ISO 3744) LWA dB (A)
Hand vibration level (ISO 5349) m
s2≤2.5 ≤2.5
Body vibration level (ISO 2631) m
s2≤0.5 ≤0.5
7

2-8
Weigths and Pressures1
TECHNICAL DESCRIPTION U/M FSR B FSR Hybrid
Machine Weight (without batteries) kg 175
Machine Weight (without fuel) kg 252
Gross Weight of the machine in work conditions
(machine + batteries + brushes + operator)
kg 323
Gross Weight of the machine in work conditions
(machine + batteries + brushes + fuel + operator)
kg 325
Weight front wheel kg 81.00 ÷61.70 78.00 ÷58.70
Front wheel pressure kg
cm2-÷- - ÷-
Weight rear right wheel kg 85.20 ÷126.20 80.00 ÷121.5
Rear right wheel pressure kg
cm2-÷- - ÷-
Weight rear left wheel kg 82.20 ÷123.20 94.00 ÷135.50
Rear left wheel pressure kg
cm2-÷- - ÷-
1Weight and Pressures depends on how many debris there are in the tray hopper and on what type of battery
the machine fits.

2-9
Part II
Anomalies Resolution Guide
9

3-10
Chapter 3
Trouble-shooting for the most common
anomalies
3.1 Electrical system: what to do if. . .
The machine doesn’t switch on
1. The emergency button is pressed ⇒Release the emergency button.
2. The key is in position 0 ⇒Rotate the key in position I.
3. The key switch is not properly con-
nected ⇒Restore the proper connections.
4. The key switch doesn’t work ⇒Replace the key switch (see section 4.1.1
at page 19).
5. The machine is not supplied ⇒Check the proper section (see section 3.1
at page 11).
10

3-11
The batteries don’t work properly
1. The batteries are not properly con-
nected ⇒Restore the proper battery connec- tions.
2. The batteries are discharged ⇒Perform a complete charge cycle.
3. Battery terminal are oxidized ⇒Disconnect the batteries, clean the
batteries terminals and reconnect
properly the batteries.
4. With the machine in working con-
ditions one battery has a voltage
lower (difference higher than 2 V)
than the other one/s
⇒If the batteries have run less than
30 charge cycles, replace the bat-
tery with lower voltage, otherwise
replace both.
5. The fuse on the loop wire is dam-
aged ⇒Check for possible short circuits, If not present replace the loop wire.
6. The power wires are damaged ⇒Replace the damaged wires.
7. The battery charger doesn’t work ⇒Check the proper section (see section 3.1
at page 11).
The battery charger doesn’t work
1. The battery charger is not con-
nected to the power supply ⇒Connect the charger to a supplied electric socket.
2. The battery charger is not con-
nected to the batteries ⇒Connect the charger to the batteries.
3. The battery charger is not properly
adjusted ⇒Adjust properly the battery charger.
4. The battery charger has one or
more lights (or LEDs) blinking con-
tinuously
⇒The battery charger is in error con-
ditions, verify the alarm tables and
solve the issue by following the re-
lated instructions (see section 5.3.3 at page
50).
5. The battery charger is properly con-
nected but it doesn’t switch on ⇒Replace the battery charger.

3-12
The display shows an alarm message
1. The display shows an alarm mes-
sage ⇒Check what alarm message is shown and solve the related issue
by following the proper instructions
(see section 5.5.1 at page 52).
The machine has a very limited working autonomy
1. The batteries connections are oxi-
dized ⇒Unplug the connection wires, wash the wire connections with water and
reconnect them protecting them with
grease.
2. With the machine in working con-
ditions one battery has a voltage
lower (difference higher than 2 V)
than the other ones
⇒If the batteries have run less than
30 charge cycles, replace the bat-
tery with lower voltage, otherwise
replace both.
3. The battery charger is not properly
adjusted ⇒Verify the type of battery in use and adjust the battery charger properly
following the instructions (see section
5.3.3 at page 50).
4. The BDI (Battery Discharge Indica-
tor) is not properly adjusted ⇒Verify the type of battery used on the machine and adjust properly the
BDI.
5. Batteries have been working for
several cycles ⇒Replace the batteries.

3-13
3.2 Main broom system: what to do if. . .
The machine doesn’t clean well
1. The machine is switched off ⇒Switch on the machine.
2. The machine doesn’t switch on ⇒Refer to the proper section (see section
3.1 at page 10).
3. The display shows an alarm mes-
sage ⇒Check what alarm message is shown and solve the related issue
by following the proper instructions
(see section 5.5.1 at page 52).
4. The microswitch of the main broom
lifting lever doesn’t work ⇒Replace the microswitch (see section 4.1.5 at page 20).
5. The main broom motor is not pow-
ered properly ⇒Check the power connections of the motor.
6. The carbon brushes are worn out ⇒Replace the carbon brushes.
7. The main broom motor is supplied
but it doesn’t work ⇒Replace the motor.
8. The brush rotates in opposite way ⇒Check the motor connections.
9. The brush is not properly engaged ⇒Release and engage properly the
brush.
10. The brush is dirty or worn ⇒Release Clean or replace the brush.

3-14 3.3 Side broom system: what to do if. . .
The machine doesn’t clean well
1. The machine is switched off ⇒Switch on the machine.
2. The machine doesn’t switch on ⇒Refer to the proper section (see section
3.1 at page 10).
3. The display shows an alarm mes-
sage ⇒Check what alarm message is shown and solve the related issue
by following the proper instructions
(see section 5.5.1 at page 52).
4. The microswitch of the side broom
lifting lever doesn’t work ⇒Replace the microswitch (see section 4.1.5 at page 20).
5. The side broom motor is not pow-
ered properly ⇒Check the power connections of the motor.
6. The carbon brushes are worn out ⇒Replace the carbon brushes.
7. The side broom motor is supplied
but it doesn’t work ⇒Replace the motor.
8. The brush rotates in opposite way ⇒Check the motor connections.
9. The brush is not properly engaged ⇒Release and engage properly the
brush.
10. The brush is dirty or worn ⇒Release Clean or replace the brush.

3-15
3.4 Vacuum system: what to do if. . .
The machine does not vacuum well
1. The machine is switched off ⇒Switch on the machine.
2. The machine doesn’t switch on ⇒Refer to the proper section (see section
3.1 at page 10).
3. The vacuum motor is switched off ⇒Switch on the vacuum motor.
4. The vacuum motor doesn’t switch
on ⇒Refer to the proper section (see section 3.4 at page 15).
5. The rubbers of the central tunnel
are worn or broken ⇒Rotate or replace the rubbers.
6. The vacuum filter is dirty or clogged ⇒Remove and clean the vacuum filter.
7. The gaskets of the filter suction
chamber does not adhere properly ⇒Check and if necessary replace the gaskets.
The vacuum motor doesn’t work properly
1. The vacuum motor is not powered
properly ⇒Check the power connections of the vacuum motor.
2. The microswitch of the vacuum mo-
tor doesn’t work ⇒Replace the microswitch.
3. The display shows an alarm mes-
sage ⇒Check what alarm message is shown and solve the related issue
by following the proper instructions
(see section 5.5.1 at page 52).
4. The vacuum motor carbon brushes
are worn out ⇒Replace the carbon brushes.
5. The vacuum motor is supplied but
it doesn’t work ⇒Replace the vacuum motor.
The filter shaker doesn’t work properly
1. The filter shaker is not powered
properly ⇒Check the power connections of the filter shaker.
2. The microswitch of the filter shaker
doesn’t work ⇒Replace the microswitch.
3. The filter shaker is supplied but it
doesn’t work ⇒Replace the filter shaker.

3-16 3.5 Frame and traction system: what to do if. . .
The traction motor doesn’t work properly
1. The machine is switched off ⇒Switch on the machine.
2. The machine doesn’t switch on ⇒Check the proper section (see section 3.1
at page 10).
3. The batteries are discharged ⇒Connect the battery charger and
perform a complete charge cycle.
4. The operator is not sitting on the
seat ⇒The operator must sit on the seat.
5. The operator is sitting on the seat ⇒Check and / or replace the deadman
seat microswitch.
6. The pedal is not pressed ⇒Press the pedal depending on the re-
quired speed.
7. The pedal is pressed ⇒Check and / or replace the poten-
tiometer or the microswitch inside
the pedal.
8. The display shows an alarm mes-
sage ⇒Check what alarm message is shown and solve the related issue
by following the proper instructions
(see section 5.5.1 at page 52).
9. The traction motor is not supplied ⇒Check the power connections of the
motor.
10. The traction motor carbon brushes
are worn out ⇒Replace the carbon brushes.
11. The traction motor is supplied but
it doesn’t work ⇒Replace the motor.
12. The electrobrake doesn’t disengage ⇒Check the connections of the electro-
brake.

3-17
3.6 Endothermic Engine: what to do if. . .
Attention: Refer to the specific manual of the manufacturer supplied with the
machine.
The engine doesn’t start
1. Check the control positions on the
motor ⇒Turn engine switch to ON position. Open the fuel valve, Move the lever
to CLOSED position unless the en-
gine is warm.
2. Check fuel ⇒Make sure that the fuel is in the tank
and that it is not of poor quality.
3. Remove and inspect spark plug ⇒Make sure that the Spark plug is not
faulty, fouled, or improperly gapped,
different than 0,70 - 0,80 mm. if the
spark plug is wet, dry and reinstall
it. Start the engine with throttle lever
in MAX position.
4. Check the engine oil level ⇒if the engine oil level is too low, drain
the exhaust oil and fuel the tank
with recommended oil to the proper
level.
5. Despite the controls, the problem is
not solved ⇒Take the engine to an authorized Honda servicing dealer, or refer to
the motor workshop manual.
The engine loses power
1. Check the air filter ⇒Clean or replace filter element(s).
2. Check the fuel ⇒Drain the fuel tank and the carbure-
tor. Refuel with fresh gasoline.
3. Despite the controls, the problem is
not solved ⇒Take the engine to an authorized Honda servicing dealer, or refer to
the motor workshop manual.

4-18
Chapter 4
Disassembling Procedures
WARNING:BEFORE TO PERFORM ANY OPERATION DESCRIBED BELOW VERIFY THAT
THE MACHINE IS TURNED OFF. DISCONNECT THE BATTERIES AND REMOVE THEM FROM
THE MACHINE. FUR THERMORE,VERIFY THAT THE PARKING BRAKE (ELECTROBRAKE)
IS ENGAGED AND THE MACHINE IS IN A TOTALLY SAFE CONDITION. IN THE ENDOTHER-
MIC ENGINE VERSION,MAKE SURE THAT THE FUEL TANK IS EMPTY,IF NOT,DRAIN IT
COMPLETELY.
18

4-19
4.1 Electrical Installation
4.1.1 Key Switch
•Put the machine in safe conditions.
•Remove the screws that secure the
front carter to the steering column
(see fig. 4.1.1-1).
•Disconnect the wires connected to
the key switch.
•Unscrew the ring nut that secures
the key switch to the steering col-
umn (see fig. 4.1.1-2).
•Remove the key switch.
•Proceed at reverse to refit the part.
4.1.1-1 4.1.1-2
4.1.2 Steering Control Card
•Put the machine in safe conditions.
•Remove the screws that secure the
upper and lower part of the steering
wheel (see fig. 4.1.2-3).
•Separate the top part from the bot-
tom part.
•Disconnect the communication ca-
ble between the Control card and the
Main card (see fig. 4.1.2-4).
•Unscrew the screws on the control
card from the top part and remove
the card (see fig. 4.1.2-4).
•Proceed at reverse to refit the part.
4.1.2-3 4.1.2-4
4.1.2-5 4.1.2-6
4.1.3 Main Card FSR B
•Put the machine in safe conditions.
•Remove the screws of the footrest
without removing it.
•Remove the screws to remove the
electrical system cover (see fig. 4.1.2-5).
•Disconnect the electrical wiring of
the Main card.
•Remove the screws that secure the
card to the support bracket and re-
move the card (see fig. 4.1.2-6).
•Proceed at reverse to refit the part.
4.1.4 Main Card FSR H
•Put the machine in safe conditions.
•Lift the upper body / seat.
•Loosen the screws to remove the
card protection cover (see fig. 4.1.4-7).
•Disconnect the electrical wiring of
the Main card.
•Remove the screws that secure the
card to the support plate to the
frame (see fig. 4.1.4-8).

4-20
•Remove the card.
•Proceed at reverse to refit the part.
4.1.4-7 4.1.4-8
4.1.5 Microswitch
•Put the machine in safe conditions.
•Remove the screws that secure the
front carter to the steering column
(see fig. 4.1.5-9).
•Disconnect the wires connected to
the microswitch.
•To remove the microswitch, unscrew
the two screws and remove the de-
vice (see fig. 4.1.5-10).
•Proceed at reverse to refit the part.
4.1.5-9 4.1.5-10
4.1.6 Emergency Button FSR B
•Put the machine in safe conditions.
•Remove the screws to remove the
electrical system cover (see fig. 4.1.6-11).
•Disconnect the electrical wiring of
the emergency button (see fig. 4.1.6-12).
•Remove the screws to remove the
emergency button (see fig. 4.1.6-13).
•Proceed at reverse to refit the part.
4.1.6-11 4.1.6-12
4.1.6-13
4.1.7 Emergency Button FSR H
•Put the machine in safe conditions.
•Remove the screws that secure the
front carter to the steering column
(see fig. 4.1.7-14).
•Disconnect the electrical wiring of
the emergency button (see fig. 4.1.7-15).
•Remove the emergency button.
•Proceed at reverse to refit the part.
4.1.8 Traction Pedal
•Put the machine in safe conditions.
•Unscrew the screws that hold the
traction pedal cover and remove it (see
fig. 4.1.8-16).