Fimap GENIE E User manual

USE AND MAINTENANCE MANUAL
GENIE E
ED. 09-2019 ENG
ORIGINAL
INSTRUCTIONS
Doc. 10004515
Ver. AC

The descriptions contained in this document are not binding.
The company therefore reserves the right to make any modifications at any time to elements,
details, or accessory supply, as considered necessary for reasons of improvement or
manufacturing/commercial requirements.
The reproduction, even partial, of the text and drawings contained in this document is prohibited
by law.
The company reserves the right to make any technical and/or supply modifications. The images
are for reference purposes only, and are not binding in terms of design and supply.
Symbols used in the manual
Open book symbol with an "i"
Indicates the need to consult the instruction manual
Open book symbol
Used to tell the operator to read the manual before using the machine
Warning symbol
Carefully read the sections marked with this symbol, for the safety of the
operator and the machine:
Warning symbol
Indicates danger of gas exhalation and leakage of corrosive liquids
Disposal symbol
Carefully read the sections marked with this symbol, for machine
disposal

3
CONTENTS
ON CONSIGNMENT OF THE MACHINE.................................................................................................................................................................. 4
SERIAL NUMBER PLATE ...................................................................................................................................................................................... 4
INTRODUCTORY COMMENT................................................................................................................................................................................. 4
INTENDED USE..................................................................................................................................................................................................... 4
TECHNICAL DESCRIPTION................................................................................................................................................................................... 5
SYMBOLS USED ON THE MACHINE...................................................................................................................................................................... 6
GENERAL SAFETY REGULATIONS....................................................................................................................................................................... 7
MACHINE PREPARATION..................................................................................................................................................................................... 8
1.HANDLING THE PACKED MACHINE...........................................................................................................................................8
2.HOW TO UNPACK THE MACHINE..............................................................................................................................................8
3.HANDLING AND TRANSPORTATION OF THE UNPACKED MACHINE..............................................................................................8
4.CONNECTING THE MACHINE...................................................................................................................................................8
5.INSTRUMENT PANEL COMPONENTS ........................................................................................................................................9
6.FIXING THE HANDLEBARS......................................................................................................................................................9
7.SOLUTION TANK....................................................................................................................................................................9
8.DETERGENT SOLUTION..........................................................................................................................................................9
9.RECOVERY TANK.................................................................................................................................................................10
10.ASSEMBLING THE BRUSH.................................................................................................................................................10
WORK................................................................................................................................................................................................................. 11
1.PREPARING TO WORK..........................................................................................................................................................11
2.OVERFLOW DEVICE .............................................................................................................................................................11
3.FORWARD MOVEMENT.........................................................................................................................................................12
AT THE END OF THE WORK................................................................................................................................................................................ 13
DAILY MAINTENANCE ........................................................................................................................................................................................ 14
1.CLEANING THE RECOVERY TANK..........................................................................................................................................14
2.EMPTYING THE SOLUTION TANK ...........................................................................................................................................14
3.CLEANING THE SQUEEGEE...................................................................................................................................................15
4.REPLACING THE SQUEEGEE RUBBERS..................................................................................................................................15
5.DISASSEMBLING THE BRUSH................................................................................................................................................16
PERIODIC MAINTENANCE .................................................................................................................................................................................. 17
1.CLEANING THE SQUEEGEE TUBE..........................................................................................................................................17
2.CLEANING THE SOLUTION TANK AND FILTER..........................................................................................................................17
TROUBLESHOOTING.......................................................................................................................................................................................... 18
1.ELECTRICAL SAFETY ...........................................................................................................................................................18
2.INSUFFICIENT WATER ON THE BRUSHES ...............................................................................................................................18
3.THE MACHINE DOES NOT CLEAN WELL..................................................................................................................................18
4.THE SQUEEGEE DOES NOT DRY PERFECTLY .........................................................................................................................18
5.EXCESSIVE FOAM PRODUCTION ...........................................................................................................................................18
CHOOSING AND USING THE BRUSHES.............................................................................................................................................................. 19
SUGGESTED POWER CABLE EXTENSION.......................................................................................................................................................... 19
MACHINE DISPOSAL .......................................................................................................................................................................................... 20
EC DECLARATION OF CONFORMITY.................................................................................................................................................................. 21

4
On consignment of the machine
When the machine is consigned to the customer, an immediate check
must be performed to ensure all the material mentioned in the shipping
documents has been received, and also to check the machine has not
suffered damage during transportation. If this is the case, the carrier must
ascertain the extent of the damage at once, informing our customer
service office. It is only by prompt action of this type that the missing
material can be obtained, and compensation for damage successfully
claimed.
Serial number plate
Introductory comment
GENIE E is a floor scrubbing machine which, by means of the mechanical
action of the rotating brush and the chemical action of a water/detergent
solution, can clean any type of flooring. As it advances, it also collects the
dirt that is removed as well as any detergent solution not absorbed by the
floor.
The machine must only be used for this purpose. Even the best
machines will only work well if used correctly and kept in good working
order. We therefore recommend you read this instruction booklet
carefully, and consult it whenever difficulties arise while using the
machine. If necessary, remember that our customer assistance service
(organised in collaboration with our dealers) is always available for advice
or direct intervention.
Intended use
The floor scrubbing machine is designed for the professional cleaning of
surfaces and floors in industrial, commercial and public environments
only. It is only suitable for use in closed (or at least covered) places.
The machine is not suitable for use in the rain, or under water jets. IT IS
FORBIDDEN to use the machine for picking up dangerous dusts or
inflammable liquids in places with an explosive atmosphere. In addition, it
is not suitable as a means of transport for people or objects.

5
TECHNICAL DESCRIPTION UM Genie E
230 V
Genie E
110 V
Nominal input power [IEC 60335-2-72; IEC 62885-9] kW 0,54 0,54
Working width mm 360 360
Width of rear squeegee mm 440 440
Working capacity m2/h 1335 1335
Brushes (diameter or length) mm 356 356
Brush rpm rpm 140 140
Force exerted on the brushes N 174 174
Brush motor – Rated voltage V/Hz 230 - 50 110 - 50
Brush motor – rated power W 320 320
Forward speed type semi-aut. semi-aut.
Forward speed Km/h 3 3
Maximum gradient 2% 2%
Suction motor – Rated voltage V - Hz 230 - 50 110 - 50
Vacuum motor – Rated power W 220 220
Maximum vacuum [IEC 62885-9; IEC 60312-1] kPa 7,2 7,2
Solution tank l 7 7
Recovery tank l 9 9
Dimensions of the open machine (Length / Height / Width) mm 615x1105x465 615x1105x465
Dimensions of the closed machine (Length / Height / Width) mm 885x425x465 885x425x465
Machine weight when empty kg 30 30
Transported machine weight kg 30 30
Weight of the machine when ready for use (GVW) kg 40 40
Sound pressure level in operator seat [ISO 11201] (LpA) dB 66.1 66.1
Uncertainty KpA dB 1.4 1.4
Hand-arm vibrations [IEC 60335-2-72; IEC 62885-9; ISO 5349-1] m/s22 2
Uncertainty 3,5% 3,5%

6
SYMBOLS USED ON THE MACHINE
Water system solenoid activation/deactivation switch symbol:
Used on the control handlebars to indicate the switch that controls the solenoid valve within the machine's water system.
Machine main switch symbol:
Used on the control handlebars to indicate the machine's main switch.
Suction motor activation/deactivation switch symbol:
Used on the control handlebars to indicate the switch that controls the machine's suction motor.
Symbol for maximum temperature for filling the solution tank:
Used near the solution tank filling hole to indicate the maximum temperature of the water used to safely fill the tank.
Electrical system earth symbol:
Used on the frame of the machine to indicate the earth point of the machine's electric system.
Maximum gradeability symbol:
Used on the serial number plate to indicate the maximum gradeability with the machine in scrubbing and drying mode.

7
GENERAL SAFETY REGULATIONS
Before using the machine, please read the following document carefully and follow
the instructions contained herein, along with the instructions in the document
supplied with the machine itself, "GENERAL SAFETY REGULATIONS" (document
code 10083659).

8
A
CB
MACHINE PREPARATION
1. HANDLING THE PACKED MACHINE
The machine is contained within specific packaging.
Every pallet consists of four machines arranged on two levels.
It is not possible to place more than two packages on top of each other.
The overall mass for a single package is 42 kg.
The overall dimensions of the package are:
A: 500 mm
B: 500 mm
C: 1150 mm
2. HOW TO UNPACK THE MACHINE
1. Open the packaging on the side indicated.
2. Extract the machine from its packaging.
3. HANDLING AND TRANSPORTATION OF THE UNPACKED MACHINE
Genie E is a machine that can be managed in all situations and transported without effort, even in small
vehicles.
Just lift the front part, using the machine handlebars as a lever. The big rear wheels mean it can be
towed anywhere and loaded on a truck by means of a simple ramp.
Genie E is easy to transport even by car. Exploiting the full flexibility of the handlebars, you can fold it
up (see the handlebars fixing section) and, with the help of a colleague, place it in the boot of the car
without disassembling any components.
4. CONNECTING THE MACHINE
For the connection, you must:
1. Connect the extension lead (not supplied) to the plug on the handlebar.
2. block the extension lead to the cable-holder handle (2) in front of the handlebars
3. connect the extension lead to the wall socket
ATTENTION: before connecting the extension lead to the socket, check
the switches are in the off (“0”) position!

9
PREPARATION OF MACHINE
5. INSTRUMENT PANEL COMPONENTS
The instrument panel components are identified as follows:
1. Main switch (1)
2. Suction switch (2)
3. Solenoid valve switch (3)
6. FIXING THE HANDLEBARS
For packaging purposes the handlebars are supplied folded; they must now be put in the working
position. Proceed as follows:
1. raise the handlebars by pulling the lever - indicated by the arrow - upwards
2. place the machine in the working position
7. SOLUTION TANK
The recovery tank must be completely empty each time the solution tank is filled.
Verify that the cap is correctly inserted in its housing (A).
Verify that the quick connection is correctly connected (B).
8. DETERGENT SOLUTION
Proceed as follows to fill the solution tank:
1. Make sure that the recovery tank is empty
2. Make sure that the main switch is off
3. Remove the inlet cap located on the right rear side of the machine.
4. Fill it with clean water at a temperature not exceeding 50C.
Add the liquid detergent to the tank in the concentration and manner indicated on the detergent
manufacturer's label. The formation of excess foam could damage the vacuum motor, so use only the
minimum amount of detergent that is necessary.

10
PREPARATION OF MACHINE
ATTENTION: Acid or alkaline maintenance detergent can be used with pH
values between 4 and 10 and that do not contain: oxidising agents, chlorine or
bromine, formaldehyde, mineral solvents.
ATTENTION: Always use detergents whose manufacturer's label indicates
their suitability for scrubbing machines. Do not use acid or alkaline products or
solvents without this indication.
always use low-foam detergent. To avoid the production of foam, put a
minimum quantity of antifoam liquid in the recovery tank before starting to
clean. Do not use pure acids.
ATTENTION: users are advised to always wear protective gloves, to avoid
the risk of serious injury to hands.
9. RECOVERY TANK
Make sure the recovery tank is empty, otherwise empty it completely.
Verify that the recovery tank is correctly inserted in its housing, and that the tubes are correctly inserted
in the tank elbows.
Verify that the caps are correctly closed.
10. ASSEMBLING THE BRUSH
To insert the brush:
1. Connect the machine to the mains power supply
2. Place the brush in front of the base body
3. Raise the brush head by using the handlebars as a lever
4. Place the brush head above the brush
5. Activate the handlebar tilt lever
6. Press the main switch to turn on the machine
7. Pulse press the dead man's lever to engage the brush to the brush head

11
WORK
1. PREPARING TO WORK
Certain operations must be carried out before starting any work:
1. Verify that the tanks are properly inserted in the housings and connected.
2. verify that the switches are in the off (“0”) position
3. connect the cable to the socket
ATTENTION: Verify that the electricity socket has a protective
conductor (or an earth conductor).
ATTENTION: Verify that the power supply voltage and frequency
comply with the nominal values required by the machine.
ATTENTION: Verify that the power supply cable is in perfect condition.
4. Carry out the operations to prepare the machine
5. lower the squeegee command lever in order to start working
4. press the main switch (1) and verify that the green indicator light comes on
5. press the suction switch (2)
6. press the solenoid valve switch (3)
At this point, the machine can work efficiently until the detergent solution runs out; use the
operating lever that activates the brushes (4)
2. OVERFLOW DEVICE
The machine is fitted with a ball filter which is activated when the recovery tank is full, causing
the suction tube to close.
In this case, it is necessary to switch off the machine and empty the recovery tank.
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.

12
WORK
3. FORWARD MOVEMENT
The traction of these machines is obtained by means of the brush which, by working slightly
inclined, is able to drag the machine forwards.
ATTENTION: Ensure that the moving brush never comes into contact
with the power supply cable.
ATTENTION: when making even brief reverse movements, verify that
the squeegee is raised.

13
AT THE END OF THE WORK
At the end of the work, and before carrying out any type of maintenance, perform the following
operations:
1. turn off the solenoid valve switch (3).
2. raise the squeegee by means of the rear handle.
3. turn off the suction switch (2).
4. Turn off the main switch (1).
5. disconnect the power cable from the mains socket.
6. Take the machine to the location designated for draining the water.
7. Disconnect the suction pipes
8. Disconnect the hook securing the recovery tank on the rear of the machine.
9. Remove the recovery tank.
10. empty the recovery tank by removing the caps and tilting it
11. disassemble the brush and clean it with a jet of water (to disassemble the brush, see
“DISASSEMBLING THE BRUSH” below)
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.

14
DAILY MAINTENANCE
PERFORM ALL MAINTENANCE OPERATIONS IN SEQUENCE
1. CLEANING THE RECOVERY TANK
1. Make sure the power cable of the machine is unplugged from the outlet
2. Disconnect the suction hose from the recovery tank
3. Disconnect the hook securing the recovery tank on the rear of the machine.
4. Remove the recovery tank.
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.
ATTENTION: Before carrying out any type of maintenance, disconnect
the machine's power supply cable.
5. Remove the caps to open the tank.
6. Clean the filter under running water.
7. Rinse the tank and clean with a jet of water
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.
2. EMPTYING THE SOLUTION TANK
Proceed as follows to empty the solution tank:
1. Switch off the solenoid valve switch
2. Switch off the suction switch
3. Switch off the main switch
4. Disconnect the power cable from the socket
5. Disconnect the quick connector on the front of the solution tank
6. Insert the Genie E solution tank discharge pipe kit (optional)
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.

15
DAILY MAINTENANCE
3. CLEANING THE SQUEEGEE
Verify that the squeegee rubbers are always clean, for a better drying action.
To clean them you must:
1. raise the machine
2. carefully clean the inside
3. carefully clean the squeegee rubbers
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.
ATTENTION: Before carrying out any type of maintenance, disconnect
the machine's power supply cable.
4. REPLACING THE SQUEEGEE RUBBERS
Verify that the state of wear and tear of the squeegee rubbers and, if necessary, replace them.
To replace it you must:
1. Raise the squeegee
2. Remove the two knobs
3. dis-assemble the squeegee from its support
4. remove the tube from the squeegee nozzle so that the squeegee can be removed
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.
ATTENTION: Before carrying out any type of maintenance, disconnect
the machine's power supply cable.

16
DAILY MAINTENANCE
5. Unscrew the knobs on the squeegee that block the rubber-pressing blades and remove
them
6. Remove the rubber-pressing blades
7. replace the rubbers
8. Reassemble everything, carrying out the above-mentioned operations in the reverse order.
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.
ATTENTION: Before carrying out any type of maintenance, disconnect
the machine's power supply cable.
5. DISASSEMBLING THE BRUSH
1. raise the squeegee
2. Raise the machine by using the handlebars as a lever and position it with the recovery tank
on the ground.
3. With the base raised, remove the brush manually by rotating it clockwise.
ATTENTION: During this operation, check there are no people or
objects near the brush.
ATTENTION: Before carrying out any type of maintenance, disconnect
the machine's power supply cable.

17
PERIODIC MAINTENANCE
1. CLEANING THE SQUEEGEE TUBE
Periodically, or whenever suction seems to be unsatisfactory, verify that the squeegee tube is
not obstructed. To clean it, proceed as follows:
1. Unplug the machine's power cable
2. Remove the tube from the sleeve on the squeegee
3. remove the other end from the recovery tank
4. wash the inside of the tube with a water jet introduced from the side where it is connected
to the tank
5. re-assemble the tube
ATTENTION: Do not wash the tube running between the suction unit
and the suction cap
2. CLEANING THE SOLUTION TANK AND FILTER
Cleaning is required as follows, either periodically or if inadequate water is emitted:
1. Disconnect the machine from the mains power supply
2. Disconnect the suction pipes
3. Remove the recovery tank retainer
4. Remove the recovery tank
5. Detach the quick connection to avoid breaking the connection itself.
6. Insert the Genie E solution tank discharge pipe kit (optional)
7. Loosen the solution tank cap
8. Remove the filter and clean it.
9. Rinse the tank and clean with a jet of water.
10. Reassemble the filter and cap.
11. Remove the discharge kit and reassemble the quick connector
12. Reassemble the recovery tank
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.
ATTENTION: Contact a FIMAP technician in case of clogging of the
quick coupling on the front of the solution tank

18
TROUBLESHOOTING
1. ELECTRICAL SAFETY
The machine is fitted with a thermal trip unit with manual reset.
The brush motor is reset by resetting the thermal trip unit located behind the handlebars.
If the machine stops repeatedly in a short space of time, you must contact the technical
assistance centre.
2. INSUFFICIENT WATER ON THE BRUSHES
1. Verify that the solution tank filter is clean
2. Verify that the solenoid valve switch is on
3. Verify that the quick connection is correctly inserted
4. Check the cock regulation screw on the water outlet
5. Check the vent pin on the solution tank cap is lowered.
3. THE MACHINE DOES NOT CLEAN WELL
1. Check the state of wear and tear of the brushes and, if necessary, replace them. The
brushes should be changed when the bristles are about 15mm long.
4. THE SQUEEGEE DOES NOT DRY PERFECTLY
1. Verify that the squeegee rubbers are clean.
2. Verify that the suction tubes are correctly inserted in their housing on the squeegee.
3. Verify that the distributor is clean.
4. Replace the rubbers, if worn
5. EXCESSIVE FOAM PRODUCTION
Check that a low foam detergent has been used. If necessary, add a small quantity of anti-
foam liquid to the recovery tank.
Remember that, when the floor is not very dirty, more foam is generated. In this case the
detergent solution should be more diluted.

19
CHOOSING AND USING THE BRUSHES
POLYPROPYLENE BRUSH (PPL)
Used on all types of floors. Good resistance to wear and tear, and hot water (no greater than 60°C.). PPL is non-hygroscopic and therefore retains its
characteristics even when working in wet conditions.
PAD HOLDER
The pad holder is recommended for cleaning shiny surfaces.
There are two types of pad holders of the CENTRE LOCK type, equipped with a snap-type central locking system in plastic that allows the abrasive floor
pads to be perfectly centred and held without any risk of them becoming detached:
1. fitted with a series of anchor points that allow the abrasive floor pad to be held and dragged while working
2. fitted with a series of groups of bristles that allow the abrasive floor pad to be held and dragged while working
TABLE FOR CHOOSING THE BRUSHES
Machine No.ofbrushes Code Type of bristles Bristles Brush Notes
GENIE E 1 421701 422213
422001
PPL
Pad holder – anchor
Pad holder – bristles
0.6
0.9
355
355
355
SUGGESTED POWER CABLE EXTENSION
CAST SCHUKO PLUG CAST SCHUKO PLUG

20
MACHINE DISPOSAL
Proceed with scrapping the machine in accordance with the waste disposal regulations in force in the country in
which the machine is being used.