Fimap MY 16 B User manual

USE AND MAINTENANCE MANUAL
MY 16 B
ED. 09-2019 ENG
Doc. 10012153
Ver. AD

The descriptions contained in this document are not binding.
The company therefore reserves the right to make any modifications at any time to elements,
details, or accessory supply, as considered necessary for reasons of improvement or
manufacturing/commercial requirements.
The reproduction, even partial, of the text and drawings contained in this document is prohibited
by law.
The company reserves the right to make any technical and/or supply modifications. The images
are for reference purposes only, and are not binding in terms of design and supply.
Symbols used in the manual
Open book symbol with an "i"
Indicates the need to consult the instruction manual
Open book symbol
Used to tell the operator to read the manual before using the machine
Warning symbol
Carefully read the sections marked with this symbol and observe the
indications, for the safety of the operator and the machine
Warning symbol
Indicates danger of gas exhalation and leakage of corrosive liquids
Warning symbol
Danger of fire: keep naked flames at a safe distance

3
CONTENTS
ON CONSIGNMENT OF THE MACHINE .................................................................................................................................................. 4
SERIAL NUMBER PLATE ..................................................................................................................................................................... 4
INTRODUCTORY COMMENT ................................................................................................................................................................ 4
INTENDED USE .................................................................................................................................................................................. 4
TECHNICAL DESCRIPTION .................................................................................................................................................................. 5
SYMBOLS USED ON THE MACHINE ...................................................................................................................................................... 6
GENERAL SAFETY REGULATIONS ....................................................................................................................................................... 7
MACHINE PREPARATION .................................................................................................................................................................... 8
1.HANDLING THE PACKED MACHINE...........................................................................................................................................8
2.HOW TO UNPACK THE MACHINE..............................................................................................................................................8
3.HOW TO MOVE THE MACHINE .................................................................................................................................................8
4.TYPE OF BATTERY.................................................................................................................................................................9
5.BATTERY MAINTENANCE AND DISPOSAL..................................................................................................................................9
6.INSERTING/CONNECTING THE BATTERIES................................................................................................................................9
7.CONNECTING THE CONNECTOR............................................................................................................................................10
8.CHARGING THE BATTERY (WITH BUILT-IN BATTERY CHARGER)................................................................................................10
9.CHARGING THE BATTERY (WITHOUT BUILT-IN BATTERY CHARGER)..........................................................................................11
10.BATTERY INDICATOR .......................................................................................................................................................12
11.INSTRUMENT PANEL COMPONENTS ..................................................................................................................................12
12.REAR COMPONENTS........................................................................................................................................................12
13.FRONT AND SIDE COMPONENTS.......................................................................................................................................12
14.LID.................................................................................................................................................................................13
15.SOLUTION TANK..............................................................................................................................................................13
16.DETERGENT SOLUTION....................................................................................................................................................13
17.REGULATING THE DETERGENT SOLUTION .........................................................................................................................14
18.ASSEMBLING THE BRUSH.................................................................................................................................................14
WORK ............................................................................................................................................................................................ 1 5 
1.PREPARING TO WORK..........................................................................................................................................................15
2.OVERFLOW DEVICE .............................................................................................................................................................16
3.FORWARD MOVEMENTS.......................................................................................................................................................16
AT THE END OF THE WORK .............................................................................................................................................................. 17
DAILY MAINTENANCE ...................................................................................................................................................................... 18
1.CLEANING THE RECOVERY TANK..........................................................................................................................................18
2.CLEANING THE SQUEEGEE...................................................................................................................................................18
3.DISASSEMBLING THE BRUSH................................................................................................................................................19
WEEKLY MAINTENANCE ................................................................................................................................................................... 20
1.CLEANING THE SQUEEGEE TUBE..........................................................................................................................................20
2.REPLACING THE SQUEEGEE RUBBERS..................................................................................................................................20
3.CLEANING THE SOLUTION TANK AND FILTER..........................................................................................................................21
TROUBLESHOOTING ........................................................................................................................................................................ 22
1.ELECTRICAL SYSTEM SAFETY...............................................................................................................................................22
2.INSUFFICIENT WATER ON THE BRUSHES ...............................................................................................................................22
3.THE MACHINE DOES NOT CLEAN WELL..................................................................................................................................22
4.THE SQUEEGEE DOES NOT DRY PERFECTLY .........................................................................................................................22
5.EXCESSIVE FOAM PRODUCTION ...........................................................................................................................................22
CHOOSING AND USING THE BRUSHES ............................................................................................................................................... 23
MACHINE DISPOSAL ........................................................................................................................................................................ 24
EC DECLARATION OF CONFORMITY .................................................................................................................................................. 25

4
On consignment of the machine
When the machine is consigned to the customer, an immediate check
must be performed to ensure all the material mentioned in the shipping
documents has been received, and also to check the machine has not
suffered damage during transportation. If this is the case, the carrier must
ascertain the extent of the damage at once, informing our customer
service office. It is only by prompt action of this type that the missing
material can be obtained, and compensation for damage successfully
claimed.
Serial number plate
Introductory comment
MY 16B is a floor scrubbing machine which, by means of the mechanical
action of the rotating brush and the chemical action of a water/detergent
solution, can clean any type of flooring. As it advances, it also collects any
dirt removed as well as the detergent solution not absorbed by the floor.
The machine must only be used for this purpose. Even the best
machines will only work well if used correctly and kept in good working
order. We therefore recommend you read this instruction booklet
carefully, and consult it whenever difficulties arise while using the
machine. If necessary, remember that our customer assistance service
(organised in collaboration with our dealers) is always available for advice
or direct intervention.
Intended use
The floor scrubbing machine is designed for the professional cleaning of
surfaces and floors in industrial, commercial and public environments
only. It is only suitable for use in closed (or at least covered) places.
The machine is not suitable for use in the rain, or under water jets. IT IS
FORBIDDEN to use the machine for picking up dangerous dusts or
inflammable liquids in places with an explosive atmosphere. In addition, it
is not suitable as a means of transport for people or objects.

5
TECHNICAL DESCRIPTION UM My16 B
Nominal input power [IEC 60335-2-72; IEC 62885-9] kW 0,61
Working width mm 410
Width of rear squeegee mm 442
Working capacity m2/h 1520
Brushes (diameter or length) mm 356
Brush rpm rpm 140
Force exerted on brush N 181
Brush motor V / W 12 - 360
Forward speed type semi-aut.
Maximum gradient 2%
Suction motor V / W 12 - 250
Maximum vacuum [IEC 62885-9; IEC 60312-1] kPa 6,62
Solution tank l 19
Recovery tank l 15
Machine dimensions (Length / Height / Width) mm 700x945x470
Battery compartment dimensions (Length / Height / Width) mm 275x245x175
Recommended battery (12 AGM 62) V / AhC512 - 62
Recommended battery weight kg 24
Machine weight when empty kg 41
Transported machine weight kg 65
Weight of the machine when ready for use (GVW) kg 84
Sound pressure level in operator seat [ISO 11201] (LpA) dB 64,7
Uncertainty KpA dB 1.4
Hand-arm vibrations [IEC 60335-2-72; IEC 62885-9; ISO 5349-1] m/s21,8
Uncertainty 3,5%

6
SYMBOLS USED ON THE MACHINE
Tap symbol
Used to indicate the solenoid valve switch
Brush symbol
Used to indicate the brush motor switch
Symbol denoting vacuum motor
Used to indicate the suction motor switch
Battery symbol
Battery charge level indicator
Indicates the maximum temperature of the detergent solution
Located near the solution tank inlet
Indicates the risk of crushed hands
Indicates the maximum gradient
Warning high voltage 110-220 Volt

7
GENERAL SAFETY REGULATIONS
Before using the machine, please read the following document
carefully and follow the instructions contained herein, along with the
instructions in the document supplied with the machine itself,
"GENERAL SAFETY REGULATIONS" (document code 10083659).

8
MACHINE PREPARATION
1. HANDLING THE PACKED MACHINE
The machine is contained within specific packaging.
Every pallet consists of two machines arranged side by side.
It is not possible to place more than two packages on top of each other.
The total weight is kg72
The overall dimensions of the package are:
A: 102,5 mm
B: 85,5 mm
C: 55 mm
A
CB
2. HOW TO UNPACK THE MACHINE
1. Open the packaging on the side indicated
2. The machine is fixed in place with supports, remove these
3. Extract the machine from its packaging
4. Use a chute to get the machine down from the pallet, pushing it backwards
5. Keep the pallet for any future transport needs
ATTENTION: If the product is delivered in cardboard containers, handle the
packed product with suitable lifting means that comply with the legal
requirements
3. HOW TO MOVE THE MACHINE
1. To safely move the machine, you should use a pallet to support it positioning wooden wedges to
block the wheels.
2. Lower the squeegee with the lever
3. Lower the brush head supporting the brush, by means of the lever
4. Secure the machine using the chocks on the wheels

9
PREPARATION OF MACHINE
4. TYPE OF BATTERY
To power the machine it is necessary to use:
The maximum dimensions of each battery are:
width 168mm
length 259mm
height 207mm
OTHER TYPES MUST NOT BE USED.
The batteries used should be of monobloc type, with a voltage of 12V 60Amp/h AGM or Gel Ah
5. BATTERY MAINTENANCE AND DISPOSAL
For maintenance and recharging, respect the instructions provided by the battery manufacturer.
Particular attention must be paid when choosing the battery charger, if not supplied, since there are
different kinds according to the type and capacity of the battery.
When the battery reaches the end of its working life, it must be disconnected by expert, trained
personnel, then lifted (using the grips and suitable lifting devices) to remove it from the battery
compartment. EXHAUSTED BATTERIES ARE CLASSIFIED AS DANGEROUS WASTE AND MUST
BE CONSIGNED TO THE AUTHORISED BODIES FOR CORRECT DISPOSAL.
6. INSERTING/CONNECTING THE BATTERIES
The machine is supplied with a built-in battery charger and an airtight gel battery. If you use batteries
other than those supplied with the machine, use only 12V 60Amp/h AGM or Gel batteries, and proceed
as follows:
1. The battery must be housed in the special compartment beneath the tank
2. Position the battery in the compartment by using the relative handle
3. Connect the clamps of the cable supplied as follows:
red clamp on the positive pole (+) of the battery
black clamp on the negative pole (-) of the battery
4. The battery must be fixed in place using the safety strap provided.
5. Check the battery is correctly inserted and does not protrude from the compartment
ATTENTION: You are advised to use airtight batteries only, to avoid the
leakage of acids!
ATTENTION: you are advised to have the electric connections made by a
qualified, FIMAP-trained technician
ATTENTION: users are advised to always wear protective gloves, to avoid the
risk of serious injury to hands.
ATTENTION: you are advised to only lift and move the batteries with lifting and
transportation means suitable for the specific weight and size

10
MACHINE PREPARATION
7. CONNECTING THE CONNECTOR
Connect the battery connector to the machine connector located above the battery compartment.
ATTENTION: This process must be carried out by qualified personnel. The
incorrect or imperfect connection of the cables to the connector can seriously
harm people and damage objects
8. CHARGING THE BATTERY (WITH BUILT-IN BATTERY CHARGER)
Perform a battery charging cycle before using the machine.
When replacing the battery, be sure to use batteries suitable for the battery charger installed (use only
12V 65A/h AGM or Gel batteries).
To charge the battery you must:
1. Make sure the recovery tank and the solution tank are empty
2. Take the machine to the designated machine storage place
ATTENTION: park the machine indoors, on a flat and level surface; near the
machine there must be no objects that could either damage it, or be damaged
through contact with it
3. Remove the battery charger connector socket protection on the back of the machine (1)
4. Plug the battery charger cable (supplied with the machine) into the freed socket
5. Plug the battery charger cable into the mains socket
6. For the correct use of the battery charger, follow the instructions in the enclosed booklet.
ATTENTION: If one of the three LEDs flashes refer to the battery charger
manual supplied with the machine
1

11
PREPARATION OF MACHINE
ATTENTION: The machine is equipped with an automatic system that
disconnects the power supply from the electrical system while the batteries are
being recharged
ATTENTION: In order not to cause permanent damage to the batteries, it is
essential to avoid their complete discharge: arrange the recharge within a few
minutes of the switching on of the "discharged batteries" blinking light.
ATTENTION: Never leave the batteries completely flat, even if the machine is
not being used.
ATTENTION: For the daily recharging of the batteries, you must fully respect
the indications provided by the manufacturer or retailer. all installation and
maintenance operations must be carried out by specialised personnel.
ATTENTION: Danger of gas exhalation and leakage of corrosive liquids.
ATTENTION: Danger of fire: Keep naked flames at a safe distance.
9. CHARGING THE BATTERY (WITHOUT BUILT-IN BATTERY CHARGER)
Perform a battery charging cycle before using the machine.
When replacing the battery, be sure to use batteries suitable for the battery charger installed (use only
12V 65A/h AGM or Gel batteries).
To charge the battery you must:
1. Make sure the recovery tank and the solution tank are empty
2. Take the machine to the designated machine storage place
ATTENTION: park the machine indoors, on a flat and level surface; near the
machine there must be no objects that could either damage it, or be damaged
through contact with it
7. Disconnect the machine connector (1) of the battery connector (2).
8. Connect the battery charger connector to the battery connector (2).
9. Wait for the green LED of the battery charger to light.
10. Disconnect the battery charger connector from the battery connector (2).
11. Connect the machine connector (1) to the battery connector (2)
ATTENTION: Carefully read the use and maintenance instructions of the
battery charger that is used for charging.
1 2

12
PREPARATION OF MACHINE
10. BATTERY INDICATOR
The battery indicator is digital, with 4 fixed positions and a flashing one. The numbers that appear on the
display show the approximate charge level.
4= maximum charge, 3= 3/4 charge, 2= 2/4 charge, 1= 1/4 charge, 0= batteries run down (flashing)
ATTENTION: A few seconds after the appearance of the flashing “0”, the
brush motor switches off automatically. With the remaining charge it is still
possible, however, to complete the drying process before recharging
11. INSTRUMENT PANEL COMPONENTS
The instrument panel components are identified as follows:
1. Main switch (1)
2. Suction switch (2)
3. Solenoid valve switch (3)
4. Digital battery level indicator (4)
12. REAR COMPONENTS
The rear components of the machine are identified as follows:
1. Squeegee lifting lever
2. Recovery tank drainage tube
3. Brush head lifting pedal
13. FRONT AND SIDE COMPONENTS
The side components of the machine are identified as follows:
1. Brush head uncoupling lever
3
4
1
2
1
2
3
1

13
B
PREPARATION OF MACHINE
2. Water-solution inlet cap
3. Solution tank cap-filter
14. LID
Check the lid is correctly inserted beneath the protruding command panel.
ATTENTION: Hand crushing hazard
15. SOLUTION TANK
Check that the water-solution filler cap is correctly screwed on.
Verify that the cap is correctly screwed into its housing (B).
Check the valve is correctly engaged (A).
16. DETERGENT SOLUTION
Proceed as follows to fill the solution tank:
1. Remove the cap of the front-mounted hopper and check the solution filter (B) is correctly
assembled.
2. Verify that the filter cap (beneath the tank) is correctly closed.
3. Fill it with clean water at a temperature not exceeding 50C. You can check the quantity in the tank
by means of the rear tube (3).
4. The recovery tank must be completely empty each time the solution tank is filled.
2
3
A

14
PREPARATION OF MACHINE
The solution tank has a maximum capacity of about 20 litres. Add the liquid detergent to the tank in the
concentration and manner indicated on the detergent manufacturer's label. The formation of excess
foam could damage the vacuum motor, so use only the minimum amount of detergent that is necessary.
ATTENTION: always use detergents whose manufacturer's label indicates
their suitability for scrubbing machines. Do not use acid or alkaline products or
solvents without this indication.
In addition, you are advised to always use low foam detergents.
Do not use pure acids.
Acid or alkaline maintenance detergent can be used with pH values between 4
and 10 and that do not contain: oxidising agents, chlorine or bromine,
formaldehyde, mineral solvents.
ATTENTION: users are advised to always wear protective gloves, to avoid the
risk of serious injury to hands.
17. REGULATING THE DETERGENT SOLUTION
Adjust the amount of solution using the tap lever on the front of the machine (1); pressing the machine's
main switch activates the brush and the machine starts to move. During the first few meters check that
the amount of solution is sufficient to wet the floor, but not excessive to exit the splash guard. Bear in
mind that the correct amount of solution always depends on the nature of the floor, the degree of dirt
and the forward speed.
18. ASSEMBLING THE BRUSH
To fit the brush, proceed as follows:
1. Raise the base by means of the appropriate pedal.
2. Position the brush on the floor, near the machine brush head
3. With the brush head up, position the brush in line with the coupling on the machine.
4. Lower the base by means of the appropriate pedal
5. Press and then immediately release the machine's main switch
WARNING! During this operation, check there are no people or objects
near the brushes.
ATTENTION: users are advised to always wear protective gloves, to
avoid the risk of serious injury to hands.
1

15
WORK
1. PREPARING TO WORK
1. Connect the electric system connector (2) to the battery connector (1)
ATTENTION: before using the machine, the operators must be suitable trained.
We therefore recommend you read this instruction booklet carefully, and consult
it whenever difficulties arise while using the machine.
2. Make sure that the recovery tank is empty
3. lower the squeegee command lever in order to start working
4. Release the base by means of the pedal
5. Press the main switch (1) and check that the green indicator light comes on and the brushes are in
operation
6. press the suction switch (2)
7. press the solenoid valve switch (3)
At this point, the machine can now begin to work at full efficiency until the detergent solution runs out, the
recovery tank is full or the battery is flat.
ATTENTION: if the machine is used in places where there is a risk of falling
objects, the operator must be provided with all the appropriate protection devices
as laid out in the legal requirements
1 2 3
1 2

16
WORK
2. OVERFLOW DEVICE
The machine is fitted with a ball filter which is activated when the recovery tank is full, causing the suction
tube to close.
In this case, it is necessary to switch off the machine and empty the recovery tank.
ATTENTION: This operation must be carried out wearing gloves to protect
against contact with dangerous solutions.
3. FORWARD MOVEMENTS
The traction of these machines is obtained by means of the brush which, working with the right weight
distribution, is able to drag the machine forwards.
ATTENTION: when making even brief reverse movements, verify that the
squeegee is raised.

17
AT THE END OF THE WORK
A
t the end of the work, and before carrying out any type of maintenance, perform the following operations:
1. Turn off the solenoid valve switch (3)
2. Turn off the suction switch (2)
3. Turn off the brush / main switch (1)
4. Raise the rear handle to lift up the squeegee
5. Raise the brush from the ground using the lifting pedal
6. Push the machine to the location provided for draining the water
7. Grasp the tube on the rear of the machine
8. Remove the drainage cap and empty the tank
To simplify the draining operation, you are advised to keep the tube bent with one hand and, with the
other, unscrew the knob and remove the plug.
Slowly straighten the tube and the liquid will start draining at the desired speed.
ATTENTION: This operation must be carried out using gloves to protect against
contact with dangerous solutions
9. Disassemble the brush and clean it with a jet of water (to disassemble the brush, see
“DISASSEMBLING THE BRUSH” below)
10. At the end of the work, park the machine in a closed place.
Do not leave the squeegee and brush head resting on the floor for a long time.
ATTENTION: Do not leave the machine unattended without first disconnecting
the electrical system connector from the battery connector. In addition, do not
park the machine in open places or on sloping floors.
1 2
3

18
DAILY MAINTENANCE
PERFORM ALL MAINTENANCE OPERATIONS IN SEQUENCE
1. CLEANING THE RECOVERY TANK
1. grasp the tube on the rear of the machine
2. Remove the drainage cap and empty the tank
ATTENTION: Before carrying out any type of maintenance,
disconnect the machine's battery connector.
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.
To simplify the draining operation, you are advised to keep the tube bent with one hand and, with the
other, unscrew the knob and remove the plug.
Slowly straighten the tube and the liquid will start draining at the desired speed.
3. Slip off the casing that covers the tank.
4. Remove the vacuum filter and clean it under running water
5. Rinse the tank and clean with a jet of water
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.
DO NOT rotate the machine while cleaning the tanks.
DO NOT rotate the machine when the tanks are full.
ATTENTION: Before carrying out any type of maintenance,
disconnect the machine's power supply cable.
2. CLEANING THE SQUEEGEE
Verify that the squeegee rubbers are always clean, for a better drying action.
To clean them you must:
1. raise the squeegee
2. Loosen the two knobs and remove the squeegee
3. remove the tube from the squeegee nozzle so that the squeegee can be removed
4. carefully clean the inside
5. carefully clean the squeegee rubbers
6. Reassemble all the elements
ATTENTION: Before carrying out any type of maintenance,
disconnect the machine's battery connector.
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.

19
DAILY MAINTENANCE
3. DISASSEMBLING THE BRUSH
1. Lower the rear lever.
2. Pressing with your foot, raise the base.
3. With the base in the raised position, activate the brush main switch with impulses. The brush will be
automatically released
4. Move the lever back into the vertical position.
ATTENTION: During this operation, check there are no people or
objects near the brush.

20
WEEKLY MAINTENANCE
1. CLEANING THE SQUEEGEE TUBE
Periodically, or whenever suction seems to be unsatisfactory, verify that the squeegee tube is not
obstructed. To clean it, proceed as follows:
1. remove the tube from the sleeve on the squeegee
2. remove the other end from the recovery tank
3. wash the inside of the tube with a water jet introduced from the side where it is connected to the tank
4. Reconnect the tube to the squeegee and the tank
ATTENTION: Do not wash the tube which goes from the tank to
the suction motor.
2. REPLACING THE SQUEEGEE RUBBERS
Verify that the state of wear and tear of the squeegee rubbers and, if necessary, replace them. To replace
it you must:
1. Raise the squeegee
2. Remove the two knobs
3. dis-assemble the squeegee from its support
4. remove the tube from the squeegee nozzle so that the squeegee can be removed
ATTENTION: Before carrying out any type of maintenance,
disconnect the machine's battery connector.
ATTENTION: This operation must be carried out wearing gloves to
protect against contact with dangerous solutions.
5. Unscrew the knobs on the squeegee that block the rubber-pressing blades and remove them
6. Remove the rubber-pressing blades
7. replace the rubbers
8. Reassemble everything, carrying out the above-mentioned operations in the reverse order.