Fisher & Paykel CE604 Series Mounting instructions

NZ AU
Installation instructions
and User guide
Ceramic glass cooktops
CE302 and CE604 models

1
Contents
Safety and warnings 2
Installation instructions 6
Introduction 14
Using your cooktop 15
Cooking guidelines 16
Care and cleaning 18
Troubleshooting 20
Warranty and service 21
Important!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please visit our local website listed on the back cover
or contact your local Fisher & Paykel dealer.

2Safety and warnings
Your safety is important to us. Please read this information before using your cooktop.
Installation
WARNING!
Electrical Shock Hazard
Disconnect the appliance from the mains electricity supply before carrying
out any work or maintenance on it.
Connection to a good earth wiring system is essential and mandatory.
Alterations to the domestic wiring system must only be made by a qualified
electrician.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Cut Hazard
Take care – panel edges are sharp.
Failure to use caution could result in injury or cuts.

3
Safety and warnings
Important safety instructions
Read these instructions carefully before installing or using this appliance.
No combustible material or products should be placed on this appliance at any time.
Please make this information available to the person responsible for installing the appliance as it
could reduce your installation costs.
In order to avoid a hazard, this appliance must be installed according to these instructions for
installation.
This appliance is to be properly installed and earthed only by a suitably qualified person.
This appliance should be connected to a circuit which incorporates an isolating switch providing
full disconnection from the power supply.
Failure to install the appliance correctly could invalidate any warranty or liability claims.

4Safety and warnings
Operation and maintenance
WARNING!
Hot Surface Hazard
During use, accessible parts of this appliance will become hot enough to
cause burns.
Do not let body, clothing or any item other than suitable cookware contact
with the ceramic glass until the surface is cool.
Never leave metal objects on the cooktop as they can become hot very
quickly.
Keep children away.
Handles of saucepans may be hot to touch. Check saucepan handles do not
overhang other cooking zones that are on. Keep handles out of reach of
children.
Failure to follow this advice could result in burns and scalds.
WARNING!
Electrical Shock Hazard
Do not cook on a broken or cracked cooktop. If the cooktop surface should
break or crack, switch the appliance off immediately at the mains power
supply (wall switch) and contact a qualified technician.
Switch the cooktop off at the wall before cleaning or maintenance.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Fire Hazard
Never leave the appliance unattended when in use. Boilover causes smoking
and greasy spillovers that may ignite.
Never use your appliance for warming or heating the room.
Failure to follow this advice may result in overheating, burning and injury.
WARNING!
Cut Hazard
The razor-sharp blade of a cooktop scraper is exposed when the safety
cover is retracted. Use with extreme care and always store safely and out
of reach of children.
Failure to use caution could result in injury or cuts.

5
Important safety instructions
Never use your appliance as a work or storage surface.
Never leave any objects or utensils other than suitable cookware on the appliance.
Do not allow children to play with the appliance or sit, stand or climb on it.
Do not store items of interest to children in cabinets above the appliance. Children climbing on
the cooktop could be seriously injured.
Do not leave children alone or unattended in the area where the appliance is in use.
Children or persons with a disability which limits their ability to use the appliance should have a
responsible and competent person to instruct them in its use. The instructor should be satisfied
that they can use the appliance without danger to themselves or their surroundings.
Do not repair or replace any part of the appliance unless specifically recommended in the
manual. All other servicing should be done by a qualified technician.
Do not use a steam cleaner to clean your cooktop.
Do not place or drop heavy objects on your cooktop.
Do not stand on your cooktop.
Do not use pans with jagged edges or drag pans across the ceramic glass surface as this can
scratch the glass.
Do not use scourers or any other harsh/abrasive cleaning agents to clean your cooktop, as these
can scratch the ceramic glass.
If the power supply cable is damaged, it must only be replaced by a qualified technician.
Do not operate your cooktop by means of an external timer or separate remote-control system.
Safety and warnings

6
Installation instructions
Cooktop and cutout dimensions
Cooktop and cutout dimensions (mm)
CE302 CE604
Aoverall width of cooktop 300 578
Boverall depth of cooktop 510 511
Cheight of chassis (below top of bench) 45 52
C1height of chassis incl. terminal block (below top of bench) 63 52
Dwidth of chassis 267 553
Edepth of chassis 483 483
Foverall width of cutout 270 560
Goverall depth of cutout 490 490
Terminal block location:
1 CE604 models - Right rear
2 CE302 models - Front left
A
C1
B
2
1
C
D
G
F
E
Drawings for illustration purposes only

7
Installation instructions
Clearances
A
B
C
C
E
D
Clearances (mm)
CE302 CE604
Aminimum clearance from rear edge of cutout to:
nearest combustible surface 55 55
Bminimum clearance from glass surface to:
rangehood 650 650
Cminimum clearance from side edges of cutout to:
nearest combustible surface 65 85
Dminimum clearance from benchtop to:
overhead cabinet not directly above the cooktop 450 450
Eminimum clearance below top of benchtop to:
thermal protection barrier 65 92
Drawings for illustration purposes only

8
Installation instructions
Before you install the cooktop, make sure that
the benchtop is square and level, and no structural members interfere with space requirements
the benchtop is made of a heat-resistant material
the cooktop will not be installed directly above a dishwasher, as the humidity may damage the
cooktop
the installation will comply with all clearance requirements and applicable standards and
regulations
a suitable isolating switch providing full disconnection from the mains power supply is
incorporated in the permanent wiring, mounted and positioned to comply with the local wiring
rules and regulations. The isolating switch must be of an approved type and provide a 3 mm air
gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules
allow for this variation of the requirements)
the isolating switch will be easily accessible to the customer with the cooktop installed
you consult local building authorities and by-laws if in doubt regarding installation
you use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces
surrounding the cooktop.
When you have installed the cooktop, make sure that
the power supply cable is not accessible through cupboard doors or drawers
there is adequate flow of fresh air from outside the cabinetry to the base of the cooktop
if the cooktop is installed directly above an oven or its base is accessible through a cupboard
or drawer space after installation, a thermal protection barrier is installed below the base of the
cooktop (see Figs.1a and 1b).
the isolating switch is easily accessible by the customer
you complete the ‘Final checklist’ at the end of these installation instructions.

9
Installation instructions
The thermal protection barrier must be:
removable
heat-resistant
made from low thermal conductivity material
at least 40 mm (CE604) or 20 mm (CE302) below the base of the cooktop to ensure adequate
ventilation
40 mm
min
Thermal protection barrier
Fig. 1b Minimum clearance below cooktop base - CE604 models
< Fresh air from
outside the
cabinetry
20 mm min.
Fig. 1a Minimum clearance below cooktop base - CE302 models
< Fresh air from
outside the
cabinetry
Thermal protection barrier

10
Fastening the cooktop to the bench (CE302 models)
1 Turn the cooktop upside down and place it on a soft surface.
2 Spread the seal around the edges of the ceramic glass with the adhesive side facing down,
making sure that the whole perimeter is sealed. Cut off any excess material.
3 Mount the supplied clamps (A) and screws (B) onto the cooktop, as shown (without tightening
the screws).
4 Place the cooktop into the cutout, then tighten the screws to clamp the cooktop securely to the
bench.
5 Using a sharp cutter or trimmer knife, trim the excess sealing material around the edge of the
cooktop. Take care not to damage the benchtop.
Note: if your bench is thicker than 40 mm, recess the underside to between 30 and 40 mm.
Installation instructions
AA
A
A
BB
B
B
Adhesive side
Fig. 3 Fastening the cooktop to the bench
Fig. 2 Preparing the cooktop
before installation
30 mm min.
40 mm max.
A
B
Seal

11
Installation instructions
Fastening the cooktop to the bench (CE604 models)
1 Turn the cooktop upside down and place it on a soft surface.
2 Spread the seal around the edges of the cooktop with the adhesive side facing down, making
sure that the whole perimeter is sealed but the ends do not overlap. Cut off any excess material.
3 Place the cooktop into the cutout and position it correctly.
4 Adjust the clamps according to the benchtop thickness (see Fig.5), then tighten the fixing screws
until the cooktop is firmly secured.
5 Using a sharp cutter or trimmer knife, trim the excess sealing material around the edge of the
cooktop. Take care not to damage the benchtop.
Note: if your bench is thicker than 40 mm, recess the underside to 30 or 40 mm.
Fig. 4 Applying the adhesive seal aroound the edges of the cooktop
Fig. 5 Clamp adjustments depending on bench thickness
Adhesive
side
30 mm
40 mm
min
40 mm
min
40 mm

12
Installation instructions
Connecting the cooktop to the mains power supply
Important!
This cooktop must be connected to the mains power supply only by a suitably qualified person.
This cooktop must be earthed.
Before connecting the cooktop to the mains power supply, check that:
1 the domestic wiring system is suitable for the power drawn by the cooktop
2 the voltage corresponds to the value given on the rating plate
3 the power supply cable sections can withstand the load specified on the rating plate.
To connect the cooktop to the mains power supply, do not use adapters, reducers, or branching
devices, as they can cause overheating and fire.
The power supply cable must not touch any hot parts and must be positioned so that its
temperature will not exceed 75
o
C at any point.
Power supply
CE302 3000W @ 220-240V~ (13 A)
CE604 6000-6500 W @ 230-240/400-415V3N~ (26-27 A)
Important!
Check with an electrician whether the domestic wiring system is suitable without alterations. Any
alterations must only be made by a qualified electrician.
To connect the power supply cable to the cooktop (CE604 models only) (Fig. 6)
1 Unscrew shield ‘A’ at the bottom of the cooktop.
2 Position the U-bolts ‘C’ onto terminal board ‘B’,
according to the connection diagrams below.
3 Feed the cable through the hole in shield ‘A’.
4 Connect the phase wires to terminal board ‘B’
according to the relevant connection diagram
below, and connect the earth wire to clamp ‘PE’.
5 Tighten the cable and fix it with cable clamp ‘E’.
6 Refit shield ‘A’.
Connection diagrams
Fig. 6 Connecting the power supply cable-CE604 models
E
C
A
B
PE
PE
123 45
230-240 V
N (L 2 )L 1
PE
12345
230-240 V 3
L
1 L 2 L 3
PE
12345
N
400-415V 3N
L 1 L 2 L 3
CE604 models
CE302 models
Single-phase connection Two-phase connection Three-phase connection
PE
N(L )
L12

13
Final checklist
TO BE COMPLETED BY THE INSTALLER
Is the cooktop earthed?
Check that the power supply cable is NOT touching the base of the cooktop. This will ensure that
the cable is not damaged by heat from the cooktop.
Check that the power supply cable is not accessible via cupboard doors or drawers.
Is the cooktop clamped down securely?
Check that all the cooking zones function correctly. Turn on all of them to a high setting and
leave them on for at least one minute. Are all elements glowing?
Is the ‘Cooking zone On’ indicator light functioning when you turn a cooking zone on? Turn all
the cooking zones on individually to check.
To check that the ‘Hot surface’ indicator functions correctly, turn off all the cooking zones. Is the
‘Hot surface’ indicator light functioning?
Have you shown the customer how to use the cooktop? Make sure you explain to the customer
about the ‘Hot surface’ indicator. Encourage them to read the full user guide before using the
cooktop.
Installer’s name:
Installer’s signature:
Installation company:
Date of installation:
LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER
Installation instructions

14
About your new cooktop
Thank you for buying an ELBA by Fisher & Paykel ceramic glass cooktop. This guide introduces
you to all its features. We recommend you read the whole guide before using your new cooktop,
for both safety and cooking success.
For more information, visit our local website listed on the back cover.
Before using your new cooktop
Read this user guide, taking special note of the ‘Safety and warnings’ section.
Remove any protective film that may still be on your cooktop.
Introduction
1 Left front cooking zone
2 Left front cooking zone control knob
3 Left rear cooking zone
4 Left rear cooking zone control knob
5 Right rear cooking zone
6 Right rear cooking zone control knob
7 Right front cooking zone
8 Right front cooking zone control knob
9 ‘Hot surface’ indicator light
10 ‘Cooking zone On’ indicator light
11 Trim
1 Front cooking zone
2 Front cooking zone control knob
3 Rear cooking zone
4 Rear cooking zone control knob
5 ‘Cooking zone On’ indicator light
6 ‘Hot surface’ indicator light
Fig.7 Cooktop layout (CE604 models) Fig.8 Cooktop layout (CE302 models)
9
33 5
56 4 2
1
1
6
4
2
8
10
711

15
The cooking zones become red when turned on full.
Whenever a cooking zone is turned on, the ‘Cooking zone On’ indicator light will glow.
When a cooking zone is turned off, the ‘Hot surface’ indicator light will glow until the glass
becomes cool enough to be safely touched.
Cooking zone controls
To begin cooking, turn the control knob of the cooking zone you wish to use to the High setting,
then adjust as necessary.
For further advice, see ‘Cooking guidelines’ following.
When you have finished cooking, turn the knob to the off (
O ) position.
When you have finished using your cooktop, make sure that all knobs are turned off and the
‘Cooking zone On’ indicator is unlit.
Using your cooktop
Fig.9 Control knob (CE604) Fig.10 Control knob (CE302)
High
High
Low
Low
OFF
OFF

16 Cooking guidelines
Cookware
Use heavy-gauge, flat, smooth-based cookware that matches the diameter of the cooking zone.
This will provide good contact with the glass and help reduce cooking times. Low heat or slow
cooking is often due to incorrect cookware size.
Cookware with a stainless steel sandwich base or enamelled cast iron will give you the best
results.
Saucepans or heavy frying pans with jagged edges or a rough base will scratch the glass.
Always lift pans off the cooktop - do not slide, or they may scratch the glass.
Never use plastic or aluminium foil dishes on the cooktop.
Aluminium and copper-based cookware will leave metallic stains on the cooktop. To prevent
these building up, clean the cooktop after every use following the instructions in ‘Care and
cleaning’. If the metallic stains are allowed to burn onto the surface, they may react with the
glass and may no longer be removable. They don’t, however, affect performance.
It is safe to place hot cookware from the oven, or another cooking zone, on the glass surface
when the surface is cool.
Avoid placing anything on a hot cooking zone until it has cooled completely.

17
Cooking guidelines
Important!
Never leave the appliance unattended when in use. Boilover causes smoking and greasy
spillovers that may ignite.
Take care when deep-frying:oil or fat can overheat very quickly, particularly on a high setting.
General cooking tips
Using a lid will reduce cooking times through retaining the heat.
Minimise the amount of liquid to reduce cooking times.
Start cooking on a high setting and reduce it when the food has come to the boil or heated
through.
Even after a cooking zone has been turned off, its glass surface retains enough heat to continue
cooking. To avoid overcooking, remove pans from hot cooking zones when the food is cooked.
Cooking rice, simmering
Some tasks, including cooking rice by the absorption method, may require a setting higher than
the lowest setting to ensure the food is cooked properly in the time recommended.
Simmering occurs below boiling point, when bubbles are just rising occasionally to the surface
of the cooking liquid. It’s the key to delicious soups and tender stews because the flavours
develop without overcooking the food. Egg-based sauces are best kept below boiling point
throughout cooking, and flour-based sauces should also be gently simmered after they have
reached boiling point.
Searing steak
1 Stand the meat at room temperature for about 20 minutes before cooking.
2 Heat up a heavy-based frying pan.
3 Brush both sides of the steak with oil and season it to taste.
4 Lower the meat onto the hot pan.
5 Turn the steak only once during cooking. The exact cooking time will depend on the thickness
of the steak and how cooked you want it. Times vary between 2 to 8 minutes per side. Press the
steak to gauge how cooked it is: the firmer it feels, the more ‘well done’ it will be.
6 Leave the steak to rest on a warm plate for a few minutes to allow it to relax and become tender
before serving.

18 Care and cleaning
What?
soiling examples
How? Important!
Light soiling on
glass after every use
fingerprints and
marks
stains left by
non-sugary
liquids (eg water,
soup, oil)
1 Wipe with a soft, damp cloth and
mild detergent. A microfibre or
‘glass’ cloth is ideal for this.
2 Wipe dry with a clean cloth or
paper towel.
Before cleaning, make sure that
the glass is a safe temperature
to touch.
Non-sugary
boilovers, spills
and food stains on
glass
burnt-on food or
grease
pasta water, milk,
soup
1 Remove the soiling with ceramic
cooktop cleaner using a sponge or
non-abrasive scourer suitable for
ceramic glass.
2 Remove any excess cleaner and
wipe dry with a clean cloth or
paper towel.
3 Apply ceramic cooktop
conditioner or protector following
the instructions on the dispenser.
A microfibre or ‘glass’ cloth is ideal
for this.
Heavy-duty scourers, some
nylon scourers and harsh/
abrasive cleaning agents
may scratch the glass. Always
read the label to check if your
cleaner or scourer is suitable.
Never leave cleaner residue
on the cooktop:the glass may
become stained.
Important!
For your safety, switch the power to the cooktop off at the wall before any cleaning. In this case,
there will be no ‘Hot surface’ indication, but the cooking zones may still be hot! Take extreme
care.
Do not use a steam cleaner to clean your cooktop.
Do not use scourers or any harsh/abrasive cleaning agents to clean your cooktop, as these can
scratch the ceramic glass or stainless steel.