Fisher-Price 79008 User manual

2
Occasionally a consumer may experience
a problem with one of our products.
If this should happen, please call us toll-free,
rather than return this product to the store.
Usually, we can solve the problem over the telephone
or send you replacement parts.
Please call Fisher-Price®Consumer Affairs,
toll-free at 1-800-432-KIDS,
between 8 AM - 5 PM EST, Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or write to:
Fisher-Price® Consumer Affairs
636 Girard Avenue
East Aurora, New York 14052.
CONSUMER INFORMATION
WARNINGS
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Never use as a carrier or lift while
child is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Never use with a child able to sit
up unassisted.
WARNING
SOUNDS 'N LIGHTS DELUXE
SOOTHING BOUNCER
Model Number: 79008
Please save these instructions for future reference.
Tool needed for adult assembly:
Phillips screwdriver (not included).
Requires one, size “D” (LR20) alkaline battery (not included) in the soothing unit.
Requires three, size “AA” (LR6) alkaline batteries (not included) in the toy bar.
Slide switch to
or AND bat
mirror for sounds
and lights!

3
PARTS
#8 - 32 x 1/2"
Screw - 2
Shown Actual Size
2 Flowers
Butterfly
2 Paddles
Toy Bar
Pad
Footrest Wire
Seatback
Wire
Right Base
Wire
Left Base
Wire
Base
Connector
#8 - 32 Nut - 2
Shown Actual Size
4
ASSEMBLY
• Place the base connector on a flat surface as shown.
• Position the left and right base wires as shown. Note the locations of
the red marks on the left and right base wire.
• Fit the left base wire into the base connector.
• Fit the right base wire into the base connector.
•Make sure both red marks on the base wires are covered by the
base connector.
1
Base
Connector
Red
Marks
Right Base
Wire
Left Base
Wire
This package contains small parts.
Adult assembly is required.
CAUTION

6
ASSEMBLY
• Insert a screw through the outside of each plastic cover and tighten with a
Phillips screwdriver. Do not over-tighten.
• Pull up on the seat back wire to be sure it is secure. If you can remove
either end of the seat back wire, you have not assembled it correctly.
Remove the screws, re-read and repeat Assembly steps 3 and 4.
4
#8 x 32 Nut
Pull Up
Protruding Side
3
5
• Position the footrest wire so that the soothing unit is upright.
• While flexing the base wires toward each other, hook the footrest wire
onto the ends of the base wires.
• Push the footrest wire down completely, below the red marks on the
base wires.
ASSEMBLY
2
Base Wire
Red Mark
Base Wire
Soothing
Unit
Footrest
Wire
Red
Mark
• Position the seat back wire with the toy bar sockets upright.
• Fit the seat back wire completely onto the base wires, so that each end
covers the red mark on each base wire.
•Make sure the plastic covers on the seat back wire cover the red
marks on the base wire.
Red
Mark Plastic
Cover
Plastic
Cover
Base
Wire
Toy Bar
Socket
Seat Back
Wire
• Fit the nut (so that the protruding side is
outward) into the hexagonal opening on
the inside of each plastic cover.

8
ASSEMBLY
• Wrap the elastic straps on the pad
flaps around the outside of each
plastic cover.
• Hook the elastic straps to the peg on
the inside of each plastic cover.
6
Elastic
Strap
Elastic
Strap
Inside View
Elastic
Strap
Plastic
Cover
Plastic
Cover
Plastic
Cover
Peg
7
ASSEMBLY
• Position the pad with the ruffle upright.
• Fit the upper pocket on the back
of the pad onto the seat back wire .
• Fit the restraint belts through the slots in
the pad .
• Lift the footrest wire. Fit the lower pocket on the back of the pad onto
the footrest wire . Lower the footrest wire.
Hint: Before assembling the lower portion of the pad to the footrest wire,
you may want to install the battery in the soothing unit. Please see the next
section (page 10, Battery Installation) for instructions.
5
Seat Back
Wire
Slot
Pad
Restraint
Belt
A
B
B
C
A
B
C

10
BATTERY INSTALLATION
Soothing Unit
• Lift the footrest wire. Remove the pad from the footrest wire.
• Insert a coin into the battery compartment door and pry the battery
compartment door off.
• Insert one, size “D” (LR20) alkaline battery, as indicated inside the
battery compartment. Be sure to place the battery on top of the ribbon.
Hint: For easy battery removal, simply lift the ribbon.
• Replace the battery compartment door and be sure it snaps securely closed.
• Replace the bottom of the pad onto the footrest wire.
• Lower the footrest wire.
Battery Compartment
Door
1.5V
“D” (LR20)
SHOWN ACTUAL SIZE
+
–
8
ASSEMBLY
7
• Fit the toy bar plugs into the socket in
each plastic cover.
• Snap the paddles to the toy bar wire.
• Fit the tab on the butterfly into the
slot in the paddle.
• The flowers can be attached to the paddles.
Hint: Twist the ends of the flowers apart to attach them to the paddles.
Assembly is now complete.
• The toy bar is removable. Simply pull up to remove.
Paddle
Paddle
Butterfly
Flowers
Plugs
Sockets
Wire Toy Bar
9

12
SET-UP & USE
Securing Your Child
• If the toy bar is attached, remove it before placing your child in the seat.
• Place your child in the seat. Position the restraint between your child’s legs.
• Fasten both belts to the buckles on each side of the restraint. Make sure
you hear a “click” on both sides.
• Check to be sure the restraint is securely attached by pulling it away from
your child. The restraint should remain attached.
• Attach the toy bar, if desired (see Assembly step 7).
1
Belt
Buckle
Restraint
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Never use as a carrier or lift while
child is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use with a child able to sit
up unassisted.
WARNING
BATTERY INSTALLATION
Toy Bar
• Locate the battery compartment door on the back side of the toy bar.
• Loosen the screw in the battery compartment door with a Phillips screwdriver
and lift to remove the door.
• Insert three, new, size "AA" (LR6) alkaline batteries, as indicated inside the
battery compartment. Be sure to place the batteries on top of the ribbon.
Hint: For easy battery removal, simply lift the ribbon.
• Replace the battery compartment door and tighten the screw with a
Phillips screwdriver. Do not over-tighten.
Battery Tips
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Remove the batteries during long periods of non-use. Always remove the
exhausted batteries from the product. Battery leakage and corrosion can
damage the product. Dispose of the batteries safely.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended in the
“Battery Installation” instructions are to be used.
• If removable rechargeable batteries are used, they are only to be charged
under adult supervision.
• Rechargeable batteries are to be removed from the product before they
are charged.
• If you use a battery charger, it should be examined regularly for damage
to the cord, plug, enclosure and other parts. Do not use a damaged
battery charger until it has been properly repaired.
SHOWN ACTUAL SIZE
1.5V x 3
“AA” (LR6) +
–
11

14
Seat Back Adjustment
The seat back can be adjusted upright or
reclined for baby’s comfort.
Reclined – Press the button on each plastic
cover to lower the seat back.
Hint: If your child is not seated in the seat, you will need to push the seat
back at the same time you are pressing both buttons on the plastic covers.
Upright – Lift the seat back until the buttons snap into the opening in
each plastic covers. Make sure you hear a "click" on each side. Push the
seat back to be sure it is secure in the upright position.
SET-UP & USE
3
Lift for
Upright
Lower for
Recline
Button
Press
Button
13
SET-UP & USE
To tighten the restraint:
• Feed the anchored end of the restraint strap up through the buckle to
form a loop .
• Pull the free end of the restraint strap .
• Repeat this procedure to tighten the other restraint strap.
To loosen the restraint:
• Feed the free end of the restraint strap up through the buckle to form
a loop .
• Enlarge the loop by pulling on the end of the loop toward the buckle.
• Pull the anchored end of the restraint strap to shorten the free end of
the restraint strap .
• Repeat this procedure to loosen the other restraint strap.
Please Note: After adjusting the restraint straps to fit your child, make
sure you pull on them to be sure they are securely fastened.
B
B
Loosen
Tighten
B
Anchored End
Free End
Anchored End
Buckle
Free End
Buckle
B
2
Press

16
To remove the pad:
• Remove the toy bar.
• Lift the footrest wire and remove the pad lower pocket.
• Fit the restraint straps back through the slots in the pad.
• Slide the pad upper pocket off of the seat back wire.
To re-assemble the pad:
• Refer to Assembly steps 5 and 6.
The pad is machine washable. Wash the pad separately
in cold water on the gentle cycle.
Do not use bleach. Tumble dry separately on low heat
and remove promptly. The frame, toy bar,
mirror, paddles, butterfly and flowers may be wiped clean
using a mild cleaning solution and a damp cloth.
Do not immerse the soothing unit or toy bar.
CARE
FCC Note (United States Only)
15
SET-UP & USE
5
Soothing Vibrations
• Make sure your child is properly secured in the seat.
• Slide the ON/OFF switch on the soothing unit to the “ON” position.
The seat will vibrate.
• Slide the ON/OFF switch on the soothing unit to the “OFF” position.
The seat will not vibrate.
IMPORTANT! If vibrations from the soothing unit become faint, or if there
are no vibrations, remove the battery from the soothing unit and dispose of it
properly. Replace the battery with a new, size “D” (LR20) alkaline battery.
Sounds and Lights
Long-Play Mode
• Slide the switch to for long-play mode. Baby delights to five minutes
of music and light patterns when the mirror is batted.
Short-Play Mode
• Slide the switch to for short-play mode. Baby enjoys one song and a
light pattern when the mirror is batted.
Off
• Slide the switch to to turn off sound and lights.
4
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©1999 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in China 79008pr-0920
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Switch
Switch