Fisher-Price J6986 Guide

J6986
www.fisher-price.com/uk
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.

This product contains small parts in
its unassembled state.
Adult assembly is required.
Base
Wires (Left and Right)
Pad
Mobile Ring
2 Toys (Toys may
be different) Frame
IMPORTANT! Please remove all parts from the pack-
age and identify them before assembly. Some parts
may be packed in the pad or frame.
2
M4 x 20 mm Screw – 4
Tighten and loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
Parts
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required.
• Tool needed for assembly: Phillips screwdriver
(not included).
• Requires one “D” (LR20) alkaline battery (not included)
for soother operation; three “C” (LR14) alkaline batteries
(not included) for mobile/sound operation.
• Product features and decoration may vary from photos.
Prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this reclined cradle on an elevated
surface. Use only on a floor.
• Suffocation Hazard - Never use
on a soft surface (bed, sofa, cush-
ion) since bouncer can tip over and
cause suffocation in soft surfaces
• Never use as a carrier or lift while
child is seated. Never use the toy
bar as a handle.
• Always use restraint system
• Never leave child unattended
• Never use as a car seat.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 Kg/20 lbs).
• Attach the provided pad (with
restraint system) to this product.
Never use this product without the
provided pad.
WARNING
CAUTION
Shown Actual Size
Consumer Information

2
• Position the wires with the toy bases down.
Hint: You may need the help of another adult to steady
the wires to complete this assembly step.
• Position the base with the ribs facing up. Fit the base
grooves to the flat end of each wire.
Hint: There is a left and right wire. The wires are designed
to fit the base one way. If a wire does not fit on one side of
the base, remove it and try fitting it to the other side of
the base.
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and instructions if
needed. Never substitute parts.
3
Base
Wires
Groove Groove
Assembly
Mobile Ring
Mobile
• Rotate the mobile up, as shown.
• Fit the mobile ring onto the top of the mobile.
• While holding the mobile, push the mobile ring until it
“snaps” into place.
• Rotate the mobile down.
1

4
• Turn the base assembly upright. Open the frame.
• While pressing the buttons on the upper frame tubes,
insert each into the sockets on the base assembly.
• Push the frame tubes in until you hear a “click”.
• Pull up on the frame to be sure it is secure.
Frame
Base Assembly
• Insert an M4 x 20 mm screw into each wire and tighten.
• Repeat this procedure to fasten the other wire to the base.
Wires
Sockets
Press Button
Assembly
Press Button
34

Lower Frame Tube
5
• Turn the assembly on its side.
• Align the hole in the lower frame tube with the hole in the
base wire.
• Insert an M4 x 20 mm screw through the lower frame tube
and base wire.Tighten the screw.
• Repeat this procedure to fasten the other side of the frame
to the base assembly.
Base Wire
Lower Frame Tubes
Base Assembly Wires
• Fit the lower frame tubes onto the base assembly wires. 6
5
Assembly

Bottom Edge of the Frame
• Fit the pocket on the bottom of the pad around the bottom
edge of the frame.
• Press the top of the pad to attach to the frame.
Pad Pocket
Pad
• Turn the assembly upright.
• Place the pad onto the frame.
• Fit the waist restraints through the slots in the pad.
eSlots
Waist Restraint
Waist Restraint
7
8
Assembly
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2006 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA
J6986a-0726
6

Soother Battery Compartment
7
Mobile and Sounds Battery Compartment
• Locate the electronic unit on the frame.You will see that
there are two battery compartments.The smaller battery
compartment powers the soother; the larger battery com-
partment powers the mobile/sounds.
• First, loosen the screw in the soother battery compart-
ment. Remove the battery compartment door. Insert one “D”
(LR20) alkaline battery, as indicated inside the battery com-
partment. Replace the battery compartment door and tighten
the screw.
• Next, loosen the screws in the mobile battery compartment
door. Insert three “C” (LR14) alkaline batteries, as indicated
inside the battery compartment. Replace the battery com-
partment door and tighten the screws.
IMPORTANT! Low battery power in the product may cause
it to operate erratically (no sounds/no movement/no vibra-
tions) and the product may not turn off. If this should happen,
remove and discard all batteries and replace with new,
alkaline batteries.
Battery Installation
Hint: We recommend the use of alkaline batteries
for longer battery life.
"D" (LR20)
1.5 Volt – Soother
"C" (LR14)
1.5 Volt x 3 – Mobile/Sounds
In exceptional circumstances, batteries may leak
fluids that can cause a chemical burn injury or ruin
your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use.Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of product in a fire.The bat-
teries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removeable, rechargeable batteries are used, they are
only to be charged under adult supervision.
Battery Safety Information
• Protect the environment by not disposing of this
product with household waste (2002/96/EC).
Check your local authority for recycling advice
and facilities (Europe only).

8
Free End
Prevent serious injury or death:
• Fall Hazard - It is dangerous to use this reclined cradle on an elevated surface.
Use only on a floor.
• Suffocation Hazard - Never use on a soft surface (bed, sofa, cushion) since
bouncer can tip over and cause suffocation in soft surfaces
• Never use as a carrier or lift while child is seated. Never use the toy bar as a handle.
• Always use restraint system
• Never leave child unattended
• Never use as a car seat.
• Not recommended for children who can sit up by themselves (6 months
approximately, until 9 Kg/20 lbs).
• Attach the provided pad (with restraint system) to this product. Never use this
product without the provided pad.
WARNING
To tighten the belts: Feed the anchored end of the restraint
up through the buckle to form a loop . Pull the free end of
the restraint .
To loosen the belts: Feed the free end of the restraint up
through the buckle to form a loop . Enlarge the loop by
pulling on the end of the loop toward the buckle. Pull the
anchored end of the restraint to shorten the free end of the
belt .
Please Note: After adjusting the restraint system to fit your
child, make sure you pull on it to be sure it is securely fastened.
Free End
Anchored End
• Place your child in the seat. Position the restraint pad
between your child’s legs.
• Fasten both waist restraints to the buckles on each side
of the restraint pad. Make sure you hear a “click” on
both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child.The restraint system should
remain attached.
Waist Restraints
Restraint Pad
Buckle
Buckle
Anchored End
TIGHTEN
Securing Baby
LOOSEN

• Pivot the speakers up to turn sound on; pivot the speakers
down to turn sound off.
1 3
• Rotate the mobile up over the seating area.
2 4
• Turn the toy bases in, toward baby.
• Fit the toys into the slots in the toy bases.
Setup
9

• Customize play for baby.You can choose to stimulate
baby's sight with the overhead motorized mobile, hearing
with music and sound effects or touch with textured toys
that are right within baby's reach.
• To turn vibrations on, slide the power switch on the elec-
tronic unit on .To turn vibrations off, slide the power
switch off .
• Slide the mobile switch on or off .
• Slide the mode switch on the electronic unit to Baby
Activated .
• When baby bats or shakes either toy, the rattling noise
activates the mobile (if it is on) and a fun sound effect or
tune (if sound is on).
Hint: Rattle sounds from other objects or toys may activate
the mobile and sounds/music.
• Slide the volume switch to low volume or high
volume .
Hint: To turn off mobile and sounds, simply slide the mode
switch on the electronic unit off .You can also slide the
mobile switch off and/or pivot the speakers down.
Baby Activated
• Select the sensory stimulation that’s just right for your
baby! Plays 10 minutes of continuous music with or
without spinning mobile.
• To turn vibrations on, slide the power switch on the
electronic unit on .To turn vibrations off, slide the
power switch off .
• Slide the mobile switch on or off .
• Slide the mode switch on the electronic unit to Parent
Activated . Music plays for about 10 minutes. If the
mobile is on, the mobile spins too!
• Slide the volume switch to low volume or high
volume .
• Music and/or mobile turns off after about 10 minutes.To
turn music and/or mobile back on, slide the mode switch
on the electronic unit off and back on again.
Hint: To turn off mobile and sounds, simply slide the
mode switch on the electronic unit to off .You can
also slide the mobile switch off and/or pivot the
speakers down.
Parent Activated
10

11
Mobile
Toy Bases
• Rotate the mobile back.
• Rotate the toy bases down.
• Pivot the speakers down.
• Fit the toys into the slots in the base.
Toy
Speakers
Toy
Slots
• The pad is machine washable.Wash it separately in cold
water on the gentle cycle. Do not use bleach.Tumble dry
separately on low heat and remove promptly.
• The frame (with liner, toy bases and mobile) and toys may
be wiped clean using a mild cleaning solution and a damp
cloth. Do not immerse the electronic unit or mobile.
To remove the pad:
• Feed the waist restraints back through the slots in pad.
• Pull to remove the pad.
• To replace the pad: refer to Assembly steps 7 - 8.
Storage Care

Questions?
If you are missing parts or need
assistance, we can help!
www.service.mattel.com/uk
01628 500303
Great Britain: Mattel UK Ltd., Vanwall Business Park, Maidenhead SL6 4UB.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121
Australia. Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre,
Harbour City, Tsimshatsui, HK, China.