Fisher-Price DELUXE PLUS HEALTHY CARE B0325 User manual

Model Number: B0325
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
Product features and decoration may vary from the photo above.
Deluxe Plus Healthy Care
High Chair
™
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m

2
Occasionally a consumer may experience a problem with one
of our products. If this should happen, please call us toll-free,
rather than return this product to the store. Usually, we can
solve the problem over the telephone or send you replace-
ment parts. Please call Fisher-Price® Consumer Relations,
toll-free at 1-800-432-5437,8AM - 6 PM EST Monday
through Friday. Hearing-impaired consumers using TTY/TDD
equipment, please call 1-800-382-7470. Or, write to:
Fisher-Price®
Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
This product contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
Consumer InformationWarnings and Caution
Prevent serious injury or death
from falls or sliding out.
•The child should be secured in
the high chair at all times by the
restraining system, either in the
recline, semi-recline or upright
position.The restraint belts must
be adjusted to fit your child
snugly.The tray is not designed
to hold the child in the chair.
•Always leave wheels locked.
•Never use near steps.
•Always keep child in view while
in the high chair.
•Never leave child unattended.
•It is recommended that the high
chair be used in the upright
position only by children capable
of sitting upright unassisted.
WARNING

Parts
3
Seat
Bottom
2 Seat Bottom Tubes
Seat Back
Frame
Frame
Footrest Back Base
4 Screw Retainers
Front Base
Hinge
Rod
Storage
Caddy
Base Tray
3 Food Trays
Pad
Headrest
#8 x 3/4" Screws
#8 x 3/4"
Screws
#8 x 3/4" Screws
#10 x 7/8"
Black Screws
#10 x 7/8"
Black Screw - 4
#10 x 7/8"
Black Screw
4 Wheels
Parts not shown: Mat and Bib.
#8 x 3/4" Screw - 8
SHOWN ACTUAL SIZE
#10 x 7/8" Black Screw - 7
SHOWN ACTUAL SIZE

•Place the seat bottom face down on a flat surface.
•At an angle, fit the footrest on the seat bottom, as shown.
Seat Bottom
Footrest
IMPORTANT! Before assembly, inspect this product for
damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken.
Contact Fisher-Price® for replacement parts and instructions
if needed. Never substitute parts.
Assembly
•Slide a seat bottom tube through each set of plastic rings
on the seat bottom.
•Align the holes in the plastic
rings and the seat bottom tubes.
•Insert a #8 x 3/4" screw through
each plastic ring and into the
seat bottom tubes, as shown.
•Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
•Push the seat bottom tubes back and forth to be sure they
are secured to the seat bottom. If the seat bottom tubes
move, you have probably not fastened them properly.
Remove the screws and check to be sure the screw holes in
the seat bottom tubes and seat bottom plastic rings are
aligned. Replace and tighten the screws.
•Insert two #10 x 7/8" black
screws through the footrest
and into the seat bottom.
•Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Footrest
Insert Screws
Here
4
Plastic
Rings
Plastic
Rings
Seat Bottom Tubes
Plastic
Rings
Plastic
Rings
Seat
Bottom
Tubes
1
2
4
3
#8 x 3/4" Screw - 4
SHOWN ACTUAL SIZE
#10 x 7/8" Black Screw - 2
SHOWN ACTUAL SIZE

•Turn the seat bottom assembly upright.
•Fit the seat back pins into the openings in the top side of
the seat bottom assembly.
Seat
Bottom
Assembly
Seat Back
Pin Seat Back
Pin
Opening
Opening
Assembly
•Turn the seat assembly face down.
•Insert the hinge rod through the hinge on the seat back
and seat bottom, as shown.
•Insert a #10 x 7/8" black screw into the hinge rod.
•Tighten the screw with a Phillips screwdriver.
Do not over-tighten.
•Set the seat assembly aside for Assembly step 11.
•Pull the frame leg out on each frame to open. Make sure it
“clicks” into place.
5
Hinge Rod
Long
Tapered
Leg Tube
Hinge
Frame Leg
•Identify the back and front base.The back base has short leg
tubes and the front base has long, tapered leg tubes.You will
use the back base for the next assembly step.
Front Base
Back Base
5
68
7
#10 x 7/8" Black Screw
SHOWN ACTUAL SIZE
Short Leg
Tube

Assembly
•While pressing the levers on the seat height adjusters, lift
them to position 4 on the frame front legs, as shown.
6
Seat Height
Adjusters
Position 4
•Position a frame so that the decorated side is outward.
•Insert the back leg of a frame into the back base.
•Fit a screw retainer over the hole in the back base, as shown.
•Insert a #10 x 7/8" black screw through the screw retainer
and back base.
•Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
•Repeat this procedure to attach the other frame back leg to
the other side of the back base.
Screw
Retainers
Frame
Back
Legs
Frame
Decorated
Side
Back Base Hole
Back Base Hole
Press Lever
9
10
•Fit the seat assembly between the two frames.
•Insert the seat bottom tubes into the sockets in each seat
height adjuster.
Seat Assembly
Seat Bottom
Tubes
Sockets Sockets
Hints:
•Be sure the seat height adjusters are in the same position
(position 4).
•You may need to push the frames apart slightly to fit the seat
bottom tubes into the seat height adjuster sockets.
11
#10 x 7/8" Black Screw - 2
SHOWN ACTUAL SIZE Screw Retainer - 2

Seat
Height
Adjuster
Seat
Height
Adjuster
Seat
Bottom
Tube Ends
Back and
Bottom View
7
Assembly
•Push each seat height adjuster
to be sure they are completely
on the seat bottom tubes.
•Insert a #8 x 3/4" screw through each seat height adjuster
and the ends of the seat bottom tube.
•Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Seat Bottom
Tube Ends
14
Push
Seat
Height
Adjuster
Push
Seat
Height
Adjuster
#8 x 3/4" Screw - 2
SHOWN ACTUAL SIZE
#8 x 3/4" Screw - 2
SHOWN ACTUAL SIZE
13
•From the back and bottom of the assembly, insert a #8 x 3/4"
screw through both seat height adjusters and the ends of
the seat bottom tube.
•Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
•Fit the frame front legs onto the front base.
•Fit a screw retainer over a hole in the front leg.
•Insert a #10 x 7/8" black screw through the screw retainer
and front leg.
•Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
•Repeat this procedure to secure the other end of the front
base with the remaining screw retainer and #10 x 7/8" black
screw.
Front Leg Hole
Front Base
Front Leg Hole
Screw Retainers
12
#10 x 7/8" Black Screw - 2
SHOWN ACTUAL SIZE
Screw Retainer - 2

Assembly
8
•Tip the assembly so that
the back of seat is flat
on the floor and the front
and back bases are
facing up.
•Insert and “snap” the peg
on a wheel into each of
the four holes in the front
and back bases.
•Lift the assembly upright.
•From the front of the assembly, place the pad onto the seat.
•Lift the bottom of the pad. Insert the two elastic loops on
the pad through the holes in the seat bottom.
•From the back and bottom of the seat, hook the elastic
loops to the tabs on the seat.
15
Wheels
Front Base
Holes
Back Base
Holes
Hole
Wheels
Wheel
Peg
Bottom View
Pad
Hole
Hole
Elastic Loops
16
Tabs
Elastic Loops
Back and
Bottom View
Hint: To remove the wheels from the front and back base,
simply pull and remove. Store the wheels in a safe place for
future use.

•Insert the crotch belt through the slot in the pad. Make
sure the crotch belt is not twisted.
•Fold the top of the pad down.
•Remove the shoulder portion of the waist/shoulder belts
by feeding them through the slots in the seat back.
Assembly
9
Crotch
Belt
Slot
Shoulder
Portion
17
18
•Lift the top of the pad.
•Thread the waist/shoulder belts through the bottom slots in
the back of the seat pad.
19
•Fit the top of the pad over the seat back.
•Fold the bottom edge of the pad under the edge of the
seat bottom to fasten it.
•First, insert the shoulder portion of the shoulder/waist belt
through the slots in the headrest pad. Then, insert the shoul-
der portion of the shoulder/waist belt through the slots in the
pad and seat back.
- Use the lower shoulder belt slots for a smaller baby.
- Use the upper shoulder belt slots for a larger baby.
Upper Shoulder Belt Slots
Lower Shoulder
Belt Slots
Headrest
Pad Slots
Shoulder
Portion
20
Pad
Bottom
Slots

10
•At an angle, fit the storage caddy onto the tab on
either frame.
Assembly is now complete.
•Fit the pad strap through the handle and press it to the
small fastener on the back of the seat.
•Fit the headrest strap through the handle and press it to the
large fastener on the back of the seat.
Handle
Large
Fastener
Small
Fastener
Pad
Strap Headrest Strap
22
Frame
Tab
Storage
Caddy
24
Back View
•Fit the strap on the top of the headrest through the handle.
Handle
Headrest
Pad Strap
Assembly
21
•From behind the seat, be sure the shoulder portion of the
waist/shoulder belts are secure in the seat back slots.
•Hook the elastic loops on each side of the pad onto the tabs
in the seat back.
Elastic
Loop
Elastic
Loop
Tab
Tab
Belt
Ends
Back View
23