Fisher-Price P4259 User manual

www.fisher-price.com
P4259

2
This package contains small parts
in its unassembled state.
Adult assembly is required.
Prevent serious injury or death from falls or
sliding out.
• The child should be secured in the high
chair at all times by the restraint system,
either in the reclining or upright position.
The restraint belts must be adjusted to fit
your child snugly. The tray is not designed
to hold the child in the chair.
• It is recommended that only children
capable of sitting upright unassisted use the
high chair in the upright position.
• Always keep child in view while using the
high chair.
• Never leave child unattended.
WARNING
Consumer Information
IMPORTANT! Please keep these instructions for future reference.
Please read these instructions before assembly and use of•
this product.
Adult assembly is required. Tool needed for assembly:•
Allen wrench (included).
Product features and decorations may vary from photographs.•
CAUTION

3
2 Front Legs 2 Back Legs
Footrest
Parts
All Fasteners Shown Actual Size
Tighten the screws with the enclosed Allen wrench.
Back Base
Seat Back with Shoulder
and Waist Belts
Seat Bottom with
Crotch Belt
2 Seat Brackets
Allen Wrench
Food Tray Snack Tray
Seat Pad
Front Base
M4 x 17mm Screw – 6 M5 x 60mm Screw – 6 M6 x 28mm Screw – 10

4
Turn the seat bottom upside down on a flat surface.•
Position a back leg so that it curves up and fit it into a large•
socket in the seat bottom.
Hint: If the leg does not seem to fit into the seat bottom socket,
try the other back leg.
Fit the other back leg into the large socket in the seat bottom.•
Insert an M5 x 60mm screw into the side of the seat bottom•
and tighten.
Push the back leg until it• "snaps" in place.
Insert an M5 x 60mm screw into the side of the seat bottom•
and tighten.
Push the back leg until it• "snaps" in place.
Assembly
1
3
4
2
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price®
for replacement parts and instructions if needed. Never substitute parts.
Back Leg
Large Socket
Seat Bottom
Back Leg
PUSH
PUSH M5 x 60mm
Screw
M5 x 60mm
Screw

5
Position a front leg so that it curves up and fit it into the small•
socket in the seat bottom.
Hint: If the leg does not seem to fit into the seat bottom, try the
other front leg.
Fit the other front leg into the small socket in the seat bottom.•
Insert two M5 x 60mm screws into the other side of the seat•
bottom and tighten.
Insert two M5 x 60mm screws into the side of the seat bottom•
and tighten.
5 7
6
8
Front Leg
Small Socket
Assembly
Seat Bottom
Front Leg
M5 x 60mm
Screws
M5 x 60mm
Screws

6
Assembly
Fit the back base onto the bottom of both back legs, as shown.•
Insert two M6 x 28mm screws into• each back leg and tighten.
Fit the sockets on the footrest onto the posts on the front of•
the assembly.
Slide the footrest up onto the posts.•
Hint: You may want to lower the seat to assemble the footrest.
Refer to page 13 for instructions to lower the seat.
Fit the front base onto the bottom of both front legs.•
Insert two M6 x 28mm screws into• each front leg and tighten.
Turn the assembly upright.•
9
10
Back Base
M6 x 28mm
Screws
M6 x 28mm
Screws
Back Legs
Front Base
Front Legs
Footrest
Posts
11
While holding the footrest in place, insert two M6 x 28mm screws•
into the holes on the back of the footrest and tighten.
12
BACK VIEW
M6 x 28mm Screws
M6 x 28mm
Screws
M6 x 28mm
Screws

7
Assembly
13
Seat Back
Peg
Holes
At an angle, fit the pegs on each side of the seat back into the•
holes in the sides of the seat bottom.
Hint: You may need to flex the bottom edge of the seat back to fit
the seat back pegs into the holes in the seat bottom.
Lift the seat back latch and push the seat back forward.•
14
Insert two M4 x 17mm screws into the seat back and tighten.•
15
M4 x 17mm
Screws
M4 x 17mm
Screws
Seat Bracket
Fit a seat bracket to the side of the seat bottom, as shown.•
Insert two M4 x 17 mm screws and tighten.•
16

8
Assembly
Fit the other seat bracket to the other side of the seat bottom,•
as shown.
Insert two M4 x 17 mm screws and tighten.•
17
M4 x 17mm
Screws
Seat Bracket
Unbuckle the lower restraint.•
18
Lower Restraint
Hint: The shoulder belts come assembled to the seat back in the
lower position for a smaller child. To change to the upper slots for
a larger child, refer to page 12.
Place the seat pad onto the seat.•
Pull the shoulder belts ends through the slots in the seat pad.•
19
Shoulder Belt
Shoulder Belt
Slots
Pull the waist belt ends through the slots in the seat pad.•
Pull the crotch belt through the slot in the seat pad.•
20
Seat Pad
Slot
Waist Belts
Crotch Belt

9
Fit the elastic loops on the seat pad down through the slots in•
the footrest.
21
Elastic Loops
Slots
Assembly
Fit the elastic loops on the seat pad bottom onto the pegs on•
the footrest.
22
Pegs
BACK VIEW
Fit the upper pocket of the seat pad onto the seat back.•
Fit the ends of the waist belts through the clips on the•
shoulder belts.
24
23
Shoulder Belts

10
Securing Your Child
Place your child in the seat. Position the crotch belt between your•
child’s legs.
Fasten both waist/shoulder belts to each side of the crotch belt.•
Make sure you hear a• "click" on both sides.
Check to be sure the restraint system is securely attached by•
pulling it away from your child. The restraint system should
remain attached.
1
Prevent serious injury or death from falls or
sliding out.
• The child should be secured in the high
chair at all times by the restraint system,
either in the reclining or upright position.
The restraint belts must be adjusted to fit
your child snugly. The tray is not designed
to hold the child in the chair.
• It is recommended that only children
capable of sitting upright unassisted use the
high chair in the upright position.
• Always keep child in view while using the
high chair.
• Never leave child unattended.
WARNING
Waist/Shoulder
Belt
Waist/Shoulder
Belt
Crotch Belt

11
• To tighten the waist belts: Feed the anchored end of the waist
belt up through the buckle to form a loop A. Pull the free end of
the waist belt B.
• To tighten the shoulder belts: Hold the adjuster and pull the
shoulder belt down C.
• To loosen the waist belts: Feed the free end of the waist belt up
through the buckle to form a loop A. Enlarge the loop by pulling
on the end of the loop toward the buckle.
Pull the anchored end of the waist belt to shorten the free end of•
the waist belt B.
• To loosen the shoulder belts: Lift the adjuster C.
Note: After adjusting the restraint system to fit your child, make sure
you pull on it to be sure it is securely fastened.
3
Tighten each waist belt/shoulder belt so that the restraint system•
is snug against your child. Please refer to the next section for
instructions to tighten the waist belts/shoulder belts.
2
Securing Your Child
TIGHTEN
LOOSEN
Adjuster Adjuster

12
To adjust the restraint height for baby, push to remove the•
shoulder belts from the seat back.
5
Shoulder Belts
Smaller Baby
Insert the ends of the shoulder belts through the lower slots in the•
pad and seat back.
7
Lower Slots
Shoulder Belts
Larger Baby
Insert the ends of the shoulder belts through the upper slots in•
the pad and seat back.
6
Upper Slots
Shoulder Belts
Securing Your Child
Unbuckle the restraint system.•
4
Restraint System

13
Adjusting Seat Recline
Hint: Adjust the seat angle to any of three positions: Upright,
Semi-Recline or Recline.
Lift the seat back latch and push the seat back forward or, pull it•
backwards to the desired position.
Push the seat back to be sure it is latched in position.•
2
Seat Adjustment
Adjusting Seat Height
Pull the levers on both seat height adjusters and lift or lower the•
seat to any of five different heights.
Make sure both sides of the seat are adjusted to the same height.•
Push the seat bottom to be sure the seat is secure.•
PULL
PULL
1
Seat Back Latch

14
4
To remove the snack tray, pull the tabs on the sides of the snack•
tray off the pegs.
Slide the tray off of the armrests.•
While pulling the release tabs on the sides of the food tray,•
adjust the tray forward or backward.
While pulling the release handles on the sides of the food tray,•
lift to remove it.
3
Using the Trays
Slide the snack tray onto the seat armrests. Push the snack tray•
until it "snaps" into place.
Fit the food tray onto the seat armrests. Push down until the tray•
"snaps" into place.
1
2
Snack Tray
Armrests
Food Tray
Hint: Before use, thoroughly wash all parts (the trays) that may contact food. The snack tray is not dishwasher safe.
The snack and food trays are not microwave safe.

15
Care
The snack tray, seat and restraint straps may be wiped clean•
using a mild cleaning solution and damp cloth. Do not use bleach.
Do not use harsh or abrasive cleansers. Rinse clean with water to
remove residue.
The food tray is dishwasher safe.•
Machine wash the seat pad in cold water with a mild detergent.•
Do not use bleach. Tumble dry on low heat and remove promptly.
To remove the pad:•
- Push to remove the shoulder belts, waist belts and crotch belt
from the seat and pads.
- Unfasten the straps on the footrest.
Remove the pad from the seat.•
To replace the pad and restraint straps, refer to the assembly•
instructions in this manual.
IMPORTANT! Be sure to replace the restraint system. Never use
this product without the restraint system.
Storage
Push down on the levers on the back legs.•
Then, push the back legs in towards the front legs.•
PUSH
Lever
Back Legs

CANADA
Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA P4259pr-0920