Fisher-Price Bounce & Spin Zebra User manual

1
DNF49
Keep this instruction sheet for future reference, as it contains important information.
For children able to get on and off unassisted.
Requires three AAA (LR03) alkaline batteries (not included).
Adult assembly is required.
Tool required: Phillips screwdriver (not included).
This product is intended for use indoors on carpeted surfaces.
Actual product may vary from the photographs.
fisher-price.com

2
#8 x 7 /8"(2,2 cm) Screw - 10
Shown Actual Size
Note: Tighten or loosen all screws with
a Phillips screwdriver.
Do not over-tighten the screws.
6 Feet
CapHandlebar
6 Base Pieces
Zebra
This package contains small parts.
For adult assembly only.
CAUTION
Parts

3
Foot
• Fit the cap into the center of the post.
Cap
Base Piece
• Insert six screws into the cap and tighten.
• Turn the assembly upright.
• Fit and “snap” each base piece between the spaces in
the feet.
Hint: The base pieces are designed to be asssembled to any
of the openings between the feet, and is a one-time assembly.
Post
• Position the zebra upside-down.
• Fit the tube end of a foot into one of the holes inside
the post.
• Assemble the other five feet into the post.
Assembly
1
3
2
4

4
• Insert four screws into the handlebar and tighten.
Battery InstallationAssembly
1,5V x 3
AAA (LR03)
• While sliding the ends of the handlebar into the indents
on each side of the zebra’s head, fit the post into the slot
in the top of the zebra’s head.
Handlebar
Post
• Protect the environment by not disposing of this
product with household waste (2012/19/EU).
Check your local authority for recycling advice
and facilities.
5
6
• For longer life use alkaline batteries.
• Locate the battery compartment on the back of
the handlebar.
• Loosen the screws in the battery compartment door and
remove the door.
• Insert three AAA (LR03) alkaline batteries.
• Replace the battery compartment door and tighten
the screws.
• If this toy begins to operate erratically, you may need to
reset the electronics. Slide the power/volume switch off and
then back on.
• When lights or sounds from this toy become faint or stop,
it’s time for an adult to change the batteries.

5
Power/Volume
Switch
Lively Music, Sounds,
Lights and Activities Too!
Battery Safety
Information
• Place this toy on a flat surface.
• Slide the power/volume switch to either ON with low volume
or ON with high volume .
• Bounce and spin while sitting on the seat. Spin the roller on
the handlebar for lights and music!
• When you are finished playing, slide the power/volume switch
OFF .
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To
avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of product in a fire. The
batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removeable, rechargeable batteries are used, they are only
to be charged under adult supervision.

6
©2015 Mattel. All Rights Reserved. DNF49-0970
PRINTED IN CHINA 1100836926-DOM
Care
• Wipe this toy with a clean cloth dampened with a mild soap
and water solution. Do not immerse this toy.
• This toy has no consumer serviceable parts. Do not take this
toy apart.
• Check the plastic parts regularly and if broken or cracked,
dispose of them properly.
Consumer Information
CO
N
SU
MER
ASS
I
S
T
A
N
C
E
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
FCC STATEMENT (UNITED STATES ONLY)
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.However, there is
no guarantee that interference will not occur in a particular
installation.If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
NOTE: Changes or modifications not expressly approved by
the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
CAN ICES-3 (B)/NMB-3 (B)
Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
L’utilisation de ce dispositif est autorisée seulement aux
conditions suivantes : (1) il ne doit pas produire de brouillage
et (2) il doit pouvoir tolérer tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible de compromettre
son fonctionnement.