Fisher-Price BUTTERFLY DREAMS Mobile C0108 User manual

www.fisher-price.com
C0108
Please keep this
instruction sheet for
future reference, as
it contains important
information.
Age: Birth to
5 months.
Adult assembly
is required.
Requires four “D”
(LR20) alkaline
batteries for the
mobile and two
“AA” (LR6) alkaline
batteries for the
remote (batteries
not included).
Tool needed for
assembly: Phillips
screwdriver
(not included).

2
Possible entanglement injury.
• Keep out of baby’s reach.
• Remove mobile from crib or playpen when baby begins
to push up on hands or knees.
• This product will not attach to all crib/cot designs.
Do not add additional strings or straps to attach to
a crib or playpen.
WARNING
• A crib mobile is intended for visual stimulation and is not to be grasped by a child.
• When used on a dresser top, do not place within the reach of a standing baby.
• Always attach by all provided fasteners (clamp) tightly to a crib or playpen
according to the instructions. Check frequently.
Consumer Information
Assembled Parts
3 Soft Toy
Spokes
3 Soft Toys
Hub
Base
Crib Adapter
3 Butterfly
Spokes
Clamp
Both Shown Actual Size
#6 x 5/8” Screw - 1 #4 x 3/8” Washer
Head Screw - 3
Tighten and loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.

3
Assembly
Butterfly Spoke
Tab
Hub
Slot
1
• Insert and “snap” the tabs on the ends of the butterfly spokes into the slots
in the hub, as shown.
Soft Toy Spoke
2
• Place the end of the spoke with the larger hole onto the matching hole on
the hub, as shown.
• Insert a #4 x 3 /8” screw through the spoke and into the hub and tighten.
• Repeat this procedure to attach the other two soft toy spokes.
This toy contains small parts in its unassembled state.
Adult assembly is required.
CAUTION

4
Soft Toy Spoke
Slot
3
• Fit a soft toy string through the slot in the end of a soft toy spoke.
• Pull down gently on the soft toy to secure the string in the soft toy spoke.
• Repeat this procedure to attach the remaining soft toys to the other two soft
toy spokes.
Assembly
Soft Toy String Soft Toy String
4
• Insert and “snap” the arm into the hole in the side of the hub.
• Fit the arm into the slot in the base, as shown.
• Insert the #6 x 5 /8” screw through the arm and into the base. Tighten
the screw.
Hub Arm
Arm
Base
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA C0108b-0920

5
Battery Installation
Battery
Compartment
Battery
Compartment
Mobile Base
• Loosen the screws in the battery compartment door. Remove the battery
compartment door.
Hint: If the crib adapter is attached to the base, loosen the screws in the crib adapter
and remove it first.
• Insert four “D” (LR20) alkaline batteries.
• Replace the battery compartment door and tighten the screws.
IMPORTANT! Under normal use conditions, the batteries in the mobile will require
replacement more often than the batteries in the remote. When sounds or light be-
come faint or movement of the mobile is sluggish, it’s time for an adult to replace the
batteries in the mobile base.
Remote
• Loosen the screw in the battery compartment door. Remove the battery compart-
ment door.
• Insert two “AA” (LR6) alkaline batteries.
• Replace the battery compartment door and tighten the screw.
IMPORTANT! If the mobile does not respond to the remote, it does not mean that
the battery power in the remote is low. Replace the batteries in the remote if the LED
signal indicator on the remote is dim when the button is pressed. If the LED signal
indicator does not light after installing new batteries in the remote, check the
orientation of the batteries in the battery compartment to make sure they are
properly installed.
Hint: We recommend using alkaline batteries for longer battery life.
• Protect the environment by not disposing of this product with house-
hold waste (2002/96/EC). Check your local authority for recycling
advice and facilities (Europe only).

6
Battery Safety Information
1.5V x 2
“AA” (LR6)
1.5V x 4
“D” (LR20)
In exceptional circumstances, batteries may leak fluids that can cause a
chemical burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted
batteries from the product. Dispose of batteries safely. Do not dispose of
product in a fire. The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged
under adult supervision.

7
• Position the base so that the battery compartment door is facing you.
• Fit the crib adapter onto the base. Tighten the screws in the crib adapter.
Crib Setup
Battery
Compartment
Door
Crib
Adapter
Tighten
Screws
• Fit the mobile base on to the crib top rail so that the threaded peg extends
outside of the crib.
• Fit the clamp onto the threaded peg and turn the clamp clockwise to secure
the base to the crib rail. Do not over-tighten the clamp.
• If the distance between the base and the mattress is less than 7 inches,
lower the crib mattress.
7"
Clamp
Threaded Peg
Crib Top Rail
Base
1
2

8
Dresser Top Setup
• Loosen the screws in the crib adapter.
• Lift and remove the crib adapter.
• Store the crib adapter in a safe place for future crib use.
Crib
Adapter
Loosen
Screws
1

9
Dresser Top Setup
• Pull the knob on the arm out. Rotate the mobile portion of the arm down.
Release the knob to lock the arm in position.
• Place the mobile on a dresser top out of reach of baby.
Knob
2

10
Use
IMPORTANT!
• In the unlikely event that use of the remote interferes with normal use of
other remote controlled equipment, such as televisions and stereos, or use
of other electric or battery powered appliances interfere with operation of
the mobile, do not use both appliances at the same time.
• For best performance between the mobile and the remote, avoid using
the remote in areas of bright light. In bright natural or artificial light, you
may notice loss of range. Move the mobile or reduce the amount of light to
improve performance.
• When using the remote, make sure that the arrow on the mobile dome is
pointing towards the transmitter window on the remote. For best results,
make sure the path between the transmitter window on the remote
and the mobile dome are in a direct line and free of obstacles. Rotate
the mobile dome so that the arrow points to the area from which you’re
most likely to use the remote. For example, if you’ll most often be using the
remote from the doorway of the nursery, make sure that the arrow on the
mobile dome is pointing towards the doorway and that the path between
the mobile dome and the doorway is free from obstructions.
Mobile Dome