Fisher-Price DMK17 User manual

1
DMK17
Keep this instruction sheet for future reference,
as it contains important information.
Requires four C (LR14) alkaline batteries and two AAA (LR03) alkaline
batteries for operation. Batteries not included.
Adult assembly is required. Tool required: Phillips screwdriver (not included).
fisher-price.com
CRAFTED BY

2
CO
N
SU
MER
ASS
I
S
T
A
N
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Jonathan Adler is a registered trademark of Jonathan Adler Enterprises, LLC and is being used pursuant to license.
© 2016 Jonathan Adler, Inc. All rights reserved.
©2016 Mattel. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, except as noted. DMK17-0970
PRINTED IN CHINA 1101051343-DOM

3
• Use as a mobile from birth to 5 months.
• A mobile is intended for visual stimulation and not to be grasped by the child.
Care
• Wipe this toy with a clean, damp cloth. Do not immerse.
WARNING
Prevent Entanglement Injury
• Keep mobile out of baby’s reach.
• Remove mobile portion of product from crib or playpen when baby begins
to push up on hands and knees.
• This product may not attach to all crib designs. Do not add additional strings
or straps to attach to a crib or playpen.
• Use ONLY attached to a crib.
CONSUMER
INFORMATION
FCC STATEMENT (UNITED STATES ONLY)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.However, there is no guarantee that
interference will not occur in a particular installation.If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
CAN ICES-3 (B)/NMB-3 (B)
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit
pas produire de brouillage et (2) il doit pouvoir tolérer tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre son fonctionnement.

4
Note: All of the screws used to assemble this toy are attached to the product. Follow these
instructions carefully to fully secure the screws. Tighten and loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.
Mobile Arm
Mobile Hub
Canopy
Soother Crib Strap Remote
PARTS
• Protect the environment by not disposing of this product with household waste
(2012/19/EU). Check your local authority for recycling advice and facilities.

5
Mobile
Arm Peg
Crib Strap
Canopy
ASSEMBLY
• Insert the peg on the mobile arm into the mobile assembly. Push to “snap” in place.
• “Snap” the mobile hub onto canopy.
2
1
y
Mobile Hub
• Fit the crib strap to the soother. Tighten both screws in the crib strap.
3

6
ASSEMBLY
• Fit the mobile arm into the socket in the soother. Tighten both screws in the
mobile arm.
5
Soother
• While pressing the button on the soother A, slide the socket door open B.
4
AB
PRESS
SLIDE
SLIDE

7
Soother
• Loosen the screws in the battery compartment door and remove the door.
• Insert four C (LR14) alkaline batteries.
• Replace the battery compartment door and tighten the screws.
• If the soother begins to operate erratically, you may need to reset the electronics.
Remove the batteries and reinstall.
IMPORTANT! Under normal use conditions, the batteries in the soother will require
replacement more often than the batteries in the remote.
• When sounds/lights/projection from the soother become faint or stop, it’s time for an
adult to change the batteries.
Remote
• Loosen the screw in the battery compartment door and remove the door.
• Insert two AAA (LR03) alkaline batteries.
• Replace the battery compartment door and tighten the screw.
• If remote control begins to operate erratically, you may need to reset the electronics.
Remove the batteries and reinstall.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of this product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.
For longer life, use alkaline batteries.
BATTERY
INSTALLATION
1,5V x 4
C (LR14)
1,5V x 2
AAA (LR03)
Soother Remote

8
CRIB
ATTACHMENT
IMPORTANT! Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to a crib
or playpen according to the instructions. Check frequently.
Crib Rail
Peg
Peg
Attachment Strap
Attachment Strap
A
B
C
D
• Position the toy inside the crib. Make sure the attachment strap is on the outside of
the crib A.
• Slide the end of the attachment strap down through the slot on the back of the
toy B.
• Pull the end of the attachment strap up and fasten to the peg on the back of the
toy C.
Note: This toy should be snug against the crib rail and spindles. Use the strap slot that
provides the tightest fit.
• If you have excess strap, slide the free end of the attachment strap up through the
opening near the top of the attachment strap D.
1

9
CRIB
ATTACHMENT
7 Inches
7 Inches
(18 cm)
(18 cm)
• Tie the toy’s strings to a crib spindle.
Note: It is better to tie the strings in a knot than a bow, since a bow may be
easily untied.
• If the distance between the base of the toy and the mattress is less than 7 inches
(18 cm), lower the crib mattress.
2
3

10
• In the unlikely event that use of the remote interferes with normal use of other remote
controlled equipment, such as televisions or stereos, or use of other electronic or battery
powered appliances interfere with operation of the mobile, do not use both at the
same time.
• You may notice a loss of range between the remote and the soother when using in
bright light. For best performance, avoid using the remote in areas of bright light. Move
the soother or reduce the amount of light to improve performance.
• Point the end of the remote towards the front of the soother. Make sure there is a clear
path between the remote and the soother.
REMOTE
USE