Fisher-Price DORA TALKING KITCHEN H1581 User manual

H1581
Instructions
www.fisher-price.com
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires three “AA” batteries for operation (included).
TM

Parts
Back Panel
Front Panel
2
Base
Arch
Countertop
Refrigerator Door
Oven Door
Small Shelf
Large Shelf
Sink
Faucet
Faucet Handle
Oven Door Handle
Refrigerator Door Handle
Dora Panel

Parts
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
3
#6 x 1/
2” Screw – 32
Fastener Shown Actual Size
Note: Tighten or loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.
2 Forks
2 Spoons
2 Plates
2 Cups
2 Cards
2 Cookies
Tomato
Banana
Chocolate
Pan
Spatula
Chicken
Cheese
Banana Pie
Rice
Butter
Empanada
2 Pancakes
Strawberry
Telephone
Sugar
Egg

4
Before Assembly
• A plastic tab was attached to the toy for in-store demonstra-
tion purposes. While the tab may have already been
removed, check to be sure it is removed. If the plastic tab
is still attached, pull and remove the tab from the product.
Throw the plastic tab away.
CAUTION
Please keep small parts such as
the plastic tab out of childrenʼs reach.
Throw the plastic tab away.
Tab
Battery Replacement
1.5V x 3
“AA” (LR6)
Shown Actual Size
Battery Safety Information
For best performance, we recommend replacing
the batteries that came with this toy with three,
new alkaline “AA” (LR6) batteries.
• Locate the battery compartment on the back of the arch.
• Loosen the screw in the battery compartment door and
remove the battery compartment door.
• Insert three “AA” (LR6) alkaline batteries into the bat-
tery compartment.
Hint: We recommend using alkaline batteries for longer
battery life.
• Replace the battery compartment door and tighten the screw.
• When sounds became faint or stop, it’s time for an adult to
replace batteries!
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product.
To avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use.
Always remove exhausted batteries from the product.
Dispose of batteries safely. Do not dispose of batteries
in a fire. The batteries may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they are only
to be charged under adult supervision.
Battery Compartment DoorBattery Compartment Door

4
5
• Place the back panel face down on a flat surface.
• Fit the small shelf to the groove in the back panel with
two tabs.
Assembly
1
2
3
Front Panel
• Fit the front panel to the shelves, as shown.
Small Shelf
Back Panel
Large Shelf
• Now, fit the large shelf to the groove in the back panel with
three tabs.
• Stand the assembly upright.
• Insert five screws into the front panel and tighten.
Shelves
Front Panel
Front View
Tabs
Tabs

6
Assembly
5
• Now, insert six screws into the back panel and tighten.
Back View
6
7
Back Panel
• Fit the main assembly into the groove around the base.
• Push down on the main assembly until it “snaps” into place.
• Reach through the back panel and push down on each
corner of the main assembly to “snap” it to the base.
Groove
Base
Main Assembly
8
• Turn the main assembly over so that the base is upright.
• Insert four screws into the base and tighten.
Base

7
Assembly
10
• Insert three screws through the pegs in the front of the main
assembly and into the countertop. Tighten the screws.
Countertop
Main Assembly
Front View
11
• Turn the assembly around so that the back faces you.
• Insert three screws through the pegs in the back of the
main assembly and into the countertop. Tighten the screws.
Back View
Countertop
Main Assembly
12
Arch
Slots
• Turn the assembly upright.
• Fit the arch into the slots in the countertop.
Countertop
Back View
9
• Place the countertop face down on a flat surface.
• Fit the main assembly to the countertop.
Countertop
Main Assembly

8
Assembly
14
• Fit the Dora panel to the groove in the arch and main
assembly, as shown.
Dora Panel
Main Assembly
Arch
15
• Insert five screws into the back of the Dora panel and tighten.
Dora Panel
• Fit the faucet onto the post on the sink.
• Fit the faucet handle into the faucet. Push down on faucet
handle until it “snaps” into place.
16
Faucet
Sink Post
Faucet Handle
13
• Insert two screws up throught the countertop and into the
ends of the arch. Tighten the screws.
Hint: You may want to tip the assembly forward and lean it
against a surface to complete this assembly step.
Arch
Countertop

9
Assembly
17
• Fit the sink into the large opening in the countertop,
as shown.
Countertop
Sink
Front View
• At an angle, fit the upper peg on the refrigerator door into
the hole in the upper hinge .
• Now, push to “snap” the lower peg on the refrigerator door
into the hole in the lower hinge .
19
Refrigerator Door


20
• Fit the handle to the holes in the oven door.
• Insert two screws through the oven door and into the handle.
Tighten the screws.
Oven Door
Oven Door
Handle
• Fit the handle to the holes in the refrigerator door.
• Insert two screws through the refrigerator door and into
the handle. Tighten the screws.
18 Refrigerator Door
Refrigerator Door
Handle

10
• Hang the cups on the hooks.
• Fit the telephone into the receiver.
• Fit a card into the Map slot.
22
Telephone
Receiver
Cups
Hooks
Card
Map Slot
Assembly
Cards
Refrigerator Door
Hint: Y ou can store the recipie cards inside the refrigerator door.
23
21
• At an angle, fit one of the pegs on the oven door into a
hole in the hinge .
• Now, push to fit the other peg on the oven door into the
other hole in the hinge .
Oven Door



11
• Place your own photos or artwork in the frames on
the refrigerataor.
• Slide the power switch on the back of the kitchen ON.
• Press the button on the radio to hear fun songs.
• Press the button on the blender for realistic sound effects.
• Lift the telephone from the receiver to “talk” with Boots,
Diego or Abuela.
Let’s Go on a Cooking Adventure
• With a recipe card inserted, touch Map for a recipe adventure.

Consumer Information
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. H1581pr-0920
©2005 Mattel, Inc. All Right Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN MEXICO
Visit us on-line at www.service.fisher-price.com
Call Fisher-Price® Consumer Relations, toll free at
1-800-432-5437, 8 AM – 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or, write to: Fisher-Price, Inc., Consumer Relations,
636 Girard Avenue, East Aurora, New York 4052.
Care
• Before using food, cooking and eating utensils, hand wash
them in hot, soapy water.
• Check plastic parts regularly and if broken or cracked,
dispose of them properly.
• Wipe this toy with a clean cloth dampened with a mild
soap and water solution, Do not immerse this toy.
• This toy has no consumer serviceable parts. Do not take
this toy apart.
FCC Statement (United
States Only)
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressively approved by
the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.