Fisher-Price Lumalou GLD09 User manual

1
Lumalou™
BETTER BEDTIME
ROUTINE SYSTEM
OWNER’S
MANUAL
GLD09

2
2
LET'S GET STARTED
1Download the app..................................................... 5
2Mount the Lumalou™ unit and the cord wrap cleat
to the wall .................................................................. 7
3Pair your device (not included)
to the Lumalou™ unit ...............................................15
4Setup routines ..........................................................17
5Set sleep and wake times .......................................18
6Ready to use ........................................................... 20

3
3
HERE IS WHAT YOU GET
M4 x 25,4 mm Screw 7,6 mm x 25,4 mm
Wall Anchor
x 4 x 4
Includes a cord wrap cleat and wall mounting fasteners.
You supply the drill, drill bit 3/16" (4,76 mm), hammer,
screwdriver and about 20 minutes of your time.
Remote uses
2 AAA batteries

4
Keep this instruction sheet for future reference, as it contains
important information.
The AC adapter and the Lumalou™ unit are not toys.
Adult assembly is required to mount the Lumalou™ unit and
the cord storage cleat to the wall and install the batteries in
the remote. Tools needed for assembly: electric drill,
3/16"(4,76 mm) drill bit, hammer and Phillips screwdriver
(tools not included).
Includes two AAA batteries for remote.
Requires an AC adapter (input 100-240 VAC, 50/60Hz,
output: 5 VDC, 1A, 5W) for operation (included).
Current/Power Rating: 0.3A MAX
x2
1,5V
AAA
(LR03)
BEFORE YOU BEGIN
WARNING
Strangulation Hazard – Children have STRANGLED in cords.
Keep the cord out of the reach of children (more than 3 feet-
0,9 meters) away.

5
DOWNLOAD THE APP
Most features of this product only work with the Fisher-Price®
Smart Connect™ app.
Download the Fisher-Price® Smart Connect™ app to create routines,
set sleep and wake times and music and light color from your smart device
(not included). The app is available on the App Store® and Google Play™.
We reserve the right to terminate digital applications after April 30, 2022
scan for compatibility

6
MOUNTING INSTRUCTIONS
Be sure to check that the Lumalou™ unit is working. Fit the cord into
the socket in the adapter and plug it in. The clock should immediately
illuminate. Press the button on the remote. Music and light should start.
Next, choose an outlet near where you plan to mount the Lumalou™ unit.
The cord from the Lumalou™ unit should be at least three feet (about one
meter) from your child's crib or bed.

7
141.66 mm
(5,6 inches)
MOUNTING INSTRUCTIONS
1
2
Locate the Lumalou™ unit and cord wrap cleat templates on pages
23 and 25. Using scissors, cut on the dotted lines to remove from
this manual.
141.66 mm (5,6 inches) 64.5 mm
(2,5 inches)
Lumalou™ Template Cleat Cord Wrap Template
Tack the Lumalou™
template to your wall.
Make sure it’s straight.
Using a pencil, make
a mark through both
circles.

8
MOUNTING INSTRUCTIONS
3
4
Check to be sure the
holes are level.
Place a level above both
pencil marks. The bubble
should be in the middle
to indicate the pencil
marks are level.
Using a 3/16" (4,76 mm),
drill bit, drill one hole
through each pencil mark
you made on the wall.

9
MOUNTING INSTRUCTIONS
5
6
Fit a wall anchor into
each of the drilled holes.
Tap each wall anchor
lightly with a hammer
until the ends of each
wall anchor are even with
the surface of the wall.
Insert a screw into
each wall anchor and
tighten with a Phillips
screwdriver. Do not
over-tighten.

10
MOUNTING INSTRUCTIONS
7
Attach the Lumalou™unit to the screws. Gently slide the unit down
to secure.

11
64.5 mm
(2,5 inches)
MOUNTING INSTRUCTIONS
Tack the cord wrap cleat
template to the wall so
that it is centered below
the Loumalou™ unit and
as close to the floor
as possible.
Using a pencil, make
a mark through both
circles.
8

12
MOUNTING INSTRUCTIONS
9
10
Check to be sure the
holes are level.
Place a level above both
pencil marks.
The bubble should be in
the middle to indicate the
pencil marks are level.
Using a 3/16" (4,76 mm),
drill bit, drill one hole
through each pencil mark
you made on the wall.

13
MOUNTING INSTRUCTIONS
11
12
Place a wall anchor into
each of the drilled holes.
Tap each wall anchor
lightly with hammer until
the ends of each wall
anchor are even with the
surface of the wall.
Align the holes on the
cord wrap cleat with the
wall anchors.
Insert two screws into
the holes in the cord
wrap and tighten with
a Phillips screwdriver.
Do not over-tighten.

14
13
IMPORTANT! Make sure the cord is taught between the Lumalou™ unit
and cord wrap cleat. Excess cord can form loops and present
a strangulation hazard.
Extend the cord straight down the wall to the cord wrap.
Wrap the cord around the cord wrap, leaving just enough to reach the
wall outlet. Make sure there is no slack.
Slide the lever on the front of the cord wrap and thread the cord through
the groove in the front of the cord wrap. Make sure the cord is fully
inserted in the groove.
Plug the cord into the AC adapter.
Plug the AC adapter into the wall outlet.
Use the AC adapter only in a wall outlet. Do not plug the adapter into
a ceiling outlet.
If the Lumalou™ unit begins to operate erratically, you may need to
reset the electronics. Unplug the AC adapter for approximately 10
seconds and plug it back in.
MOUNTING INSTRUCTIONS

15
PAIR THE LUMALOU™ UNIT TO YOUR DEVICE
Open the Fisher-Price® Smart Connect™ app on your device (not
included) and touch the Lumalou™ icon on the Smart Connect™
dashboard. Be sure your device is within approximately 1,8 meters - 6 feet
of the Lumalou™ unit to pair.
Press the pairing button on the Lumalou™ unit. Once paired, the clock on
the Lumalou™ unit updates to the current time.
If you cannot pair your device with the Lumalou™ unit, try moving the
device closer to the unit.
Pairing
Button
en
t
he
F
is
he
r
Pr
ic
e®
S
ma

16
HOME SCREEN
Change Clothes
Brush Teeth
Pack Bag
Eat
Read
Clean Up
Wash Up
Custom Task 1
Custom Task 2
Custom Task 3
Go Potty
Customize settings like light colors
and light brightness, song and sound
choices, light and sound timers, volume,
and to turn ON/OFF Ready, Settle,
Sleep™ lights and sounds playlist.
Choose Routines or Sleep Trainer
and then touch this button to setup
a routine/sleep times for each day of
the week.
There are eight tasks and three custom tasks (you assign them) to
create a routine.

17
LET'S CREATE A ROUTINE
First assign a name to the routine. For example, you could name it "Morning".
Next, create the routine by selecting tasks in the order you would like them
completed.
Remember, you can create your own task. For example, you can assign "Brush
Your Hair to the asterisk icon. .
Then, choose each day of the week this routine should be followed. Use the pull
down menu to select a start time for the routine.
You can create multiple routines but only one routine can be saved per day.

18
SLEEP TRAINING SCHEDULE
Starting with Sunday, add a bedtime and a wake time for each day of the week
by using the pull down menus to choose both times. You can also set up a nap
time too!
Touch to advance to the next day.
Make sure you enter times for each day
of the week!

19
NAP TIME
Touch to start nap time on your device or press the
button on the underside of the remote. The start
button changes to a stop button if you'd like to stop
the nap timer or press the same button on the
underside of the remote.
Touch this button on the home screen to play your
light and sound choices during a nap. Or press the
top button on the remote.

20
START A ROUTINE
TASK COMPLETED
When it's time to start
a routine, all of the tasks will
pulse until your child presses
the button on the remote.
Then, only the first task lights.
You can end the routine at
any time using the app or by
pressing the button on the
underside of the remote.
After completing a task, your
child must press the button on
the remote to move on to the
next task. Complete all tasks in
the routine for a fun reward.