Fisher-Price Musical Scoop Coupe User manual

Model Number: 78617
Please save these instructions for future reference.
Adult assembly is required.
Ages: 11/2- 5 years.
Weight Limit: 50 lbs. (23 kgs)
Tools needed for assembly: Cap Nut Assembly Tool (included),
Hammer, Scrap Block of Wood (optional)
™

Parts
Cap Nut
Assembly Tool
2
• Please save all packaging material until assembly is complete to ensure that no parts are discarded.
Not Shown: 2 Label Sheets
Vehicle Body
8 Cap Nuts
4 Wheels
Roof
Rear Door
Rear Axle
Rear Door
Hinge Pin
2 Front Axles
4 Bushings
Steering
Wheel
Chime Unit
Steering
Wheel
Retainer
Long Spacer
Long Spacer
Short Spacer
4 Washers
2 Ice Cream Scoops
2 Cones
SHOWN ACTUAL SIZE
8 Cap Nuts
4 Washers
• Adult supervision is required.
• Never use near steps, sloped driveways, hills, roadways, alleys,
swimming pool areas or other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one rider.
WARNING

Assembly
CAUTION
• The rear axle, rear door hinge pin and front axles were
secured to the vehicle body for shipment. Remove and set
these parts aside for assembly. Slide the front axles toward
the center of the vehicle body to remove them.
• Position the vehicle body upright.
• Wipe the areas where labels will be applied with a clean,
dry cloth. Apply labels 2, 21, 18 and 19 to the vehicle body
as shown above. For best results, avoid repositioning a
label once it has been applied.
• Stand the vehicle body on its back end.
• From the underside of the vehicle, fit the steering wheel
retainer into the hole in the vehicle body.
• From the top side of the vehicle body, fit the steering
wheel stem through the hole in the dash area and into
the steering wheel retainer.
•Press firmly to snap the steering wheel into the retainer.
You may need to rotate the steering wheel while pressing
it into the retainer.
Please keep small parts and plastic bags
out of children’s reach. Dispose of
plastic bags properly.
1
2
19
18 21
2
3
Front Axles
Rear Door
Hinge Pin
Rear Axle
Vehicle Body
Vehicle Body
Hole
Vehicle Body
Steering Wheel
Retainer
Steering Wheel
3
• Wipe the areas where labels will be applied with a clean,
dry cloth. Apply labels 6, 9 and 12 to the vehicle body as
shown above. For best results, avoid repositioning a label
once it has been applied.
4Roof
12
9
6

• Place a cap nut into the cupped end of the cap nut
assembly tool.
• Hold the cap nut against one end of the rear door hinge
pin and tap the end of the cap nut assembly tool with a
hammer to secure the cap nut on the end of the hinge pin.
Helpful Hint! The rear door hinge pin is the longer of the two
straight rods.You may want to position the end of the hinge
pin on a scrap block of wood to protect the assembly surface.
Assembly
• Position the vehicle body upright.
• Fit the hooks on the front roof supports into the openings
in the vehicle body .
• Align the tab on the side roof support with the slot in the
vehicle body .
•Press firmly on the roof directly above the side support to
snap it into the vehicle body .
C
B
A
5
6
Front Roof
Supports
PRESS
Side Roof
Support
A
B
C
Cap Nut
Assembly Tool
Rear Door
Hinge Pin
Scrap Block of Wood
Cap Nut
Note: You may need the help of another adult to complete
assembly steps 7 and 8.
• Position the vehicle body to stand on its front end.
• Fit the rear door to the vehicle body. Align the hinge line
holes in the rear door with the hinge line holes in the
vehicle body.
• Insert the rear door hinge pin up through the hole in the
vehicle body and into the rear door; through the rear door
and into the roof; and out through the hole in the top of
the roof.
Helpful Hint! You may need to open and close the rear door
to align the hinge line as you’re inserting the rear door hinge
pin through the vehicle body, rear door and roof. Once you’ve
aligned the end of the hinge pin with the hole in the top of
the roof, tap the cap nut end of the hinge pin with a hammer
to drive the hinge pin out through the hole in the roof.
7
Roof
Rear Door
Hinge Pin
Rear Door
4

Assembly
• Place a cap nut into the cupped end of the cap nut
assembly tool.
• Support the opposite (bottom) end of the rear door
hinge pin.
• Hold the cap nut against the end of the hinge pin and
tap the end of the cap nut assembly tool with a hammer
to secure the cap nut on the end of the hinge pin.
• Before beginning this assembly step, note that one side
of the chime unit has ribs in the center hole (see inset).
• Slide the end of the rear axle through the hole in the
vehicle body until the end of the axle is at the center
of the vehicle body.
• Fit a long spacer onto the end of the axle.
• Fit the chime assembly, ribbed side first, onto the
rear axle.
• Fit another long spacer onto the rear axle.
• Continue to slide the rear axle through the vehicle body.
810
Cap Nut
Rear
Door
Hinge
Pin
Bottom End
Cap Nut
Assembly
Tool
• Note the single tab on the rear axle. Slide a wheel, “hubcap”
side out, onto that end of the rear axle.
• Place a cap nut into the cupped end of the cap nut
assembly tool.
• Hold the cap nut against the end of the rear axle.Tap the
end of the cap nut assembly tool with a hammer to secure
the cap nut on the end of the rear axle.
Helpful Hint! You may want to position the end of the rear
axle on a scrap block of wood to protect the assembly surface.
9
Rear Axle
Single Tab
Scrap Block of Wood
5
Cap Nut
Assembly
Tool
Cap Nut
“Hubcap”
Side
Wheel
Ribs
Chime
Unit
Long
Spacer
Long
Spacer Rear Axle
INSET
Ribs
Chime Unit

Note: The front axles are not interchangeable and are marked
A and B. Identify front axle B.
• Fit a washer on the short leg of front axle B.
• Fit a wheel, “hubcap” side up, on the short leg of front axle B.
• Place a cap nut in the cupped end of the cap nut
assembly tool.
• Hold the cap nut against the end of the short leg.Tap the
cap nut assembly tool with a hammer to secure the cap nut
on the end of the short leg of front axle B.
A
Cap Nut
Cap Nut
Assembly Tool
Wheel
Washer
Short
Leg
“Hubcap”
Side
Front
Axle B
A
Front
Axle A Front Axle B
B
Assembly
Note: You may need the help of another adult to complete
this assembly step.
• Fit the short spacer onto the end of the axle.
• Fit a wheel, “hubcap” side out, onto the rear axle.
• Place a cap nut into the cupped end of the cap nut
assembly tool.
• Support the opposite end of the rear axle. Hold the cap nut
against the end of the rear axle and tap the cap nut assem-
bly tool with a hammer to secure the cap nut on the end of
the rear axle.
• Fit a washer on the long leg of front axle B.
• Fit a bushing, plate side first, onto the long leg of front
axle B.
11
12
13
Cap Nut
Assembly
Tool
Cap Nut
“Hubcap”
Side
Wheel
Rear Axle
6
Plate Side
Bushing
Front Axle B
Washer
Long Leg
• Position the vehicle body upright.
• Lift the front end of the vehicle and insert the long leg of
front axle B up into the hole marked B in the vehicle body.
Make sure the bushing inserts into the hole in the
vehicle body.
• Lower the vehicle body.
14
Bushing
Washer
Hole B
Short
Spacer

Label decoration
Front/LEFT Side View
Front View
• Wipe the areas where the labels will be applied with a
clean, dry cloth.
• Wash your hands before applying labels to the vehicle.
• Apply labels as indicated in the illustrations.
• For best results, avoid repositioning a label once it has
been applied.
• Snap the ice cream scoops to the top of the cone.
7
Assembly
• Fit a bushing, barrel side first, onto the end of front axle B.
Press the bushing into the hole.
• Place a cap nut in the cupped end of the cap nut
assembly tool.
• Hold the cap nut against the end of front axle B.Tap the
cap nut assembly tool with a hammer to secure the cap
nut on the end of front axle B.
• Repeat steps 12 - 15 to assemble front axle A to the
the vehicle body.
One time assembly is now complete.
15
Cap Nut
Assembly Tool
Cap Nut
Hole
Front Axle B
Barrel Side
Bushing
16
Cone
Ice Cream Scoop
1
1
4
17 17
16 16
15 15
13
3
™

Rear/RIGHT Side View
Label decoration
Inside of Door
Fisher-Price, Inc., a subsidiary of Mattel, Inc.,
East Aurora, New York 14052, U.S.A.
©1998 Mattel, Inc. All Rights Reserved. Printed in U.S.A.
® and ™ designate U.S. trademarks of Mattel, Inc. 78617-0920
If you have any questions about this product:
In CANADA - Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2. Questions? 1-800-567-7724.
In GREAT BRITAIN - Mattel U.K., Ltd., Helpline: 01628 500302.
In AUSTRALIA - Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812 (valid only in Australia).
Questions? We’d like to hear from you!
Call Fisher-Price®Consumer Affairs, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to:
Fisher-Price®Consumer Affairs
636 Girard Avenue
East Aurora, New York 14052
• Periodically inspect all retainers and protective coverings and tighten as required. Check plastic pieces on a regular basis for
cracks or broken pieces.
• To clean or to remove static electricity, wash the vehicle with a mild soap and water solution and soft cloth. Rinse clean with
water to remove soap residue and towel dry.
Care and Maintenance
8
3
5
13
10
11
8
7
14
20