Fisher-Price V4436 User manual

www.fisher-price.com
www.fisher-price.com
V4436
V4436

2
CO
N
S
UMER
ASS
I
S
T
A
N
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
FCC Statement (United States Only)
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. V4436pr-0920
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA

3
Consumer Information
WARNING
Prevent Entanglement Injury
• Keep mobile out of baby’s reach.
• Remove mobile portion of product from crib or playpen
when baby begins to push up on hands and knees.
• This product may not attach to all crib designs. Do not add
additional strings or straps to attach to crib or playpen.
• Use ONLY attached to a crib or playpen.
IMPORTANT! Always attach with all provided fasteners tightly to a crib or playpen according to the
instructions. Do not add additional strings or straps to attach to a crib. Check frequently.
• Please keep this instruction sheet for future reference, as it contains important information.
• Requires three "C" (LR14) alkaline batteries for mobile/base operation (batteries
not included).
• Adult assembly is required.
• Tool required for assembly: Phillips screwdriver (not included).
• The mobile portion of this product may be used from birth until 5 months.
• The base portion of this product may be used from birth until 24 months.
• A crib mobile is intended for visual stimulation and is not to be grasped by a child.
Care
• Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not
immerse this toy. The soft toys are surface washable.
• This toy has no consumer serviceable parts. Do not take this toy apart.
• If this product begins to operate erratically, you may need to reset the electronics.
Slide the power/volume switch off and then back on.
ICES-003
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NMB-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit
pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.

4
Parts
Note: All of the screws used to assemble this toy are attached to the product.
Follow these instructions carefully to fully secure the screws. Tighten and loosen all
screws with a Phillips screwdriver. Do not over-tighten the screws.
Mobile Arm Mobile Cap
3 Thick Spokes
3
Th
k
Sp
3 Toys
3 Thin Spokes
Base

5
1,5V x 3
"C" (LR14)
• Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove
the battery compartment door.
• Insert three "C" (LR14) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screws.
• When sounds or motion become faint or stop, it’s time for an adult to change
the batteries.
Battery Installation
In exceptional circumstances, batteries may leak fluids that can cause a chemical
burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of this product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
•
If removable, rechargeable batteries are used, they are only to be charged under adult supervision.
Battery Safety Information
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities
(Europe only).

6
• Fit the thin mobile spokes onto the pegs on the mobile arm.
Hint: The spokes are designed to fit on alternating pegs one way. If a thin spoke does not
seem to fit, try the next peg.
1
1
Assembly
Thin Spoke
Thin Spoke
Thin Spoke
1
2
• Fit the thick mobile spokes onto the remaining pegs on the mobile arm.
Thick Spoke
Thick Spoke
Thick Spoke

7
1
4
• Fit the T-end of the strap on each mobile toy through the slot in each thick spoke.
• Pull down on each toy to be sure it is secure.
Assembly
• Fit the mobile cap over the ends of the thin and thick spokes and onto the top of the
mobile arm.
• Tighten the screw in the mobile cap.
1
3
Mobile Cap
Toy
Toy
Toy

8
Base
1
5
• First, press the button on the base next to the socket Aand then slide the socket
door open B.
• Fit the mobile arm into the socket in the base and tighten both screws.
Assembly
A
B

9
Crib Attachment
1
1
IMPORTANT! If you are attaching this toy to a crib side rail that can be lowered
and raised, make sure the crib side rail is in the raised (locked) position whenever
a child is in the crib.
• Position the base inside the crib.
• Wrap the attachment strap around the top of the crib rail.
• Slide the end of the attachment strap under the tabs on the back of the base.
• Fasten the attachment strap slot to the peg on the back of the base.
Note: This toy should be snug against the crib rail and spindles. Use the strap
slot that provides the tightest fit.
Attachment Strap
Attachment Strap
Peg
Peg
Crib Rail
IMPORTANT! Always attach all provided fasteners (strings, straps, clamps, etc.)
tightly to a crib or playpen according to the instructions. Do not add additional
strings or straps to attach to a crib. Check frequently.

10
Crib Attachment
• Tie the toy’s strings to a crib spindle.
Note: It is better to tie the strings in a knot than a bow, since a bow may be
easily untied.
1
3
• Make sure the distance between the bottom of the product and the crib mattress
is at least 7 inches (18cm).
• If the distance is less than 7 inches (18cm): readjust the attachment strap to lift
the product; or lower the crib mattress.
1
2
At Least 7 Inches (18cm)
At Least 7 Inches (18cm)
Mattress
Mattress
Bottom of Base
Bottom of Base