Fisher-Price W1710 User manual

www.fisher-price.com
W1710
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three “AA” (LR6) alkaline batteries (not included) for operation.
Adult assembly is required. Required tool: Phillips screwdriver (not included).
Wipe with a clean, damp cloth. Do not immerse.
This toy has no consumer serviceable parts. Do not take apart.

1
Assembled Parts
Upper Ramp
Large Tree Canopy
Teeter-totter
Handle
Gate Platform
Peek-a-boo Door
Flag
Base
Canopy Swing
Hut Roof
WallTree
Lower Ramp
Part not shown: Label Sheet
CAUTION
This product contains small parts in an unassembled state.
Adult assembly is required.
Base
#6 x 58" (1,6 cm) Screw – 3
Shown Actual Size
Tighten all screws with a Phillips
screwdriver. Do not over-tighten.

2
• Turn the assembly over.
• Fit the post on the teeter-totter into the hole in the wall assembly.
Hint: You may need to turn the teeter-totter to fit it in place.
• Push to “snap” in place.
• Fit the tree onto the wall.
• Lay the assembly face down on a flat surface and insert a screw into the wall and tighten.
1
2
Assembly
Teeter-totter
Post
Tree
Wall
Tr
Screw
Back View
Back View

3
• Turn the assembly upright.
• Fit the tabs on to the bottom of the wall assembly into the slots in the base.
Hint: If the tabs on the wall assembly do not seem to fit, turn it around and try again!
• Push near each tab to “snap” in place.
3
Assembly
• At an angle, fit the peg on one side of the peek-a-boo door into the socket in the wall.
• Then, push to “snap” the other peg in place.
• Fit the tabs on the hut roof into the slots in the tree. Push to “snap” in place.
4
5
Peek-a-boo Door
Hut Roof

4
Assembly
• First fit the tab on the platform into the slot in the backside of the wall
A
. Then, fit the upper ramp into
the slot in the front of the wall
B
.
• Push to “snap” the platform and upper ramp into the wall.
6Upper Ramp
Platform
Back View
Back View
A
B
• From the back of the wall assembly, first fit the top of the lower ramp onto the tabs on the upper
ramp A. Then, fit the tab on the bottom of the lower ramp into the slot in the base B.
• Push to “snap” in place.
7
Lower Ramp
Upper Ramp Tabs
Base Slot
Back View
A
B

5
• Fit the canopy swing onto the outer tree branch, as shown. Push to “snap” in place.
8
Canopy Swing
• Fit the large tree canopy onto the remaining tree branch. Push to “snap” in place.
9
Large Tree Canopy
Assembly

6
• Fit the gate into the socket in the base, as shown. Push to “snap” in place.
11 Gate
• Fit the handle onto the pegs on the wall assembly.
• Insert two screws into the handle and tighten.
10
Handle
2 Screws
Assembly

7
• Before applying the labels, wipe the surface with a clean, dry cloth to remove any dust or oils.
• Place the labels exactly as shown in the illustration and avoid repositioning the labels.
• After applying a label, rub it firmly with a clean dry cloth, starting at the center, to remove any
air bubbles.
Decoration
1
3
2
5
9
8
7
4
6
• Insert the flag into any of the sockets in the assembly.
12
Flag
Assembly

8
• Locate the battery compartment door on the bottom of the toy.
• Loosen the screw in the battery compartment door and remove it.
• Insert three, new “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screw. Do not over-tighten.
• If this toy begins to operate erratically, you may need to reset the electronics. Slide the
power/volume switch off and then back on.
• When sounds from this toy become faint or stop, it’s time for an adult to change the batteries.
1,5V x 3
“AA” (LR6)
Battery Installation
• Protect the environment by not disposing of this product with household waste (2002/96/EC).
Check your local authority for recycling advice and facilities (Europe only).

9
ICES-003
NMB-003
• This Class B digital apparatus complies with Canadian ICES-003.
• Operation is subject to the following two conditions: (1) this device may not cause harmful interference
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne doit pas produire
de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu,
même si ce brouillage est susceptible de compromettre le fonctionnement
du dispositif.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury
or ruin your toy. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries from the
toy. Dispose of batteries safely. Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging.
• If removable, rechargeable batteries are used, they are only to be charged under
adult supervision.