Fisher-Price GROW-WITH-ME TRIKE 72667 User manual

Grow-With-Me Trike
Model Number: 72667
Please keep these instructions for future reference.
Adult assembly is required.
Tools needed for assembly: Hammer, Phillips Screwdriver, Scrap Block of Wood.
If you have any questions about this product, or are missing a part, please call us toll-free
at 1-800-432-KIDS, rather than return this product to the store.
Age: 2 - 6 years.
Weight Limit: 60 lbs.
Instructions

Thank you for purchasing the Fisher-Price®Grow-With-Me
Trike for your child. The Grow-With-Me Trike starts off as a
regular tricycle for the youngest riders and then converts to a
low rider as your child grows.
The Grow-With-Me Trike requires adult assembly. Please set
aside at least 30 minutes for assembly. Please read these
instructions carefully and identify all parts before assembly.
Refer to the parts illustration for identification.
Please keep small parts, hardware and
plastic bags out of children’s reach. Dispose
of plastic bags properly.
CAUTION
WARNING
• Adult supervision is required.
• Never use near steps, sloped driveways, hills,
ditches, roadways, alleys, swimming pool
areas or other bodies of water.
• Always wear shoes or sneakers.
• Never allow more than one rider.
• Observe child weight limit: maximum 60 lbs.
Message to Parents
2
Consumer Information
Questions? We'd like to hear from you!
Call Fisher-Price®Consumer Affairs, toll-free at
1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470. Or, write to: Fisher-Price®
Consumer Affairs, 636 Girard Avenue, East Aurora,
New York 14052.
Fisher-Price, Inc., a subsidiary of Mattel, Inc.,
East Aurora, New York 14052, U.S.A.
©1999 Mattel, Inc. All Rights Reserved. Printed in Mexico
® and ™ designate U.S. trademarks of Mattel, Inc. A 72667-0920

3
3
4
6
8
911
17
Illustration
Number Part Description Quantity
1 Front Wheel 1
2 Pedal Hub 4
3 Pedal Axle 1
4 Pedal 2
5 Lock Washer 2
6 Fork 1
7 Pedal Axle Cover 2
8 Frame 1
9 Handlebar 1
10 Gas Cap 1
Illustration
Number Part Description Quantity
11 Seat 1
12 Seat Retainer 1
13 Rear Wheel 2
14 Straight Axle 1
15 Hubcap 2
16 Cap Nut 2
17 Cap Nut Assembly Tool 1
18 #8 x 3" Screw 1
19 #8 x 3/4" Screw 4
Label Sheet (not shown) 1
1
77
2
2
12
13
14
• Please save all packaging material until assembly is complete to ensure that no parts are discarded.
• If you are missing a part, please call us toll-free at 1-800-432-KIDS, rather than return this product to the store.
• Please wipe each part with a clean, dry cloth before assembly.
Parts
10
15
16
13
4
55
5
#8 x 3" Screw – 1
18 #8 x 3/4" Screw – 4
19
(ALL SHOWN ACTUAL SIZE)
Lock Washer – 2 Cap Nut – 2
16

• Place a scrap block of wood on a flat surface.
• Fit a cap nut into the cap nut assembly tool.
• Place one end of the straight axle into the cap nut.
• Tap the end of the straight axle with a hammer. Make sure
the cap nut is securely attached to the straight axle.
• Remove the cap nut assembly tool from the cap nut.
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
Cap Nut
Cap Nut
Assembly Tool
Straight Axle
Rear Wheel
Indented
Side Down
Straight Axle
4
• Place a scrap block of wood on a flat surface.
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the cap nut assembly tool under the assembled rear
wheel and onto the cap nut.
• Slide a rear wheel (indented side up) onto the end of the
straight axle.
• Slide a hubcap (peg side down) onto the straight axle.
• Place a cap nut on the end of the straight axle.
• Tap the cap nut with a hammer. Make sure the cap nut is
securely attached to the straight axle.
• Dispose of the cap nut assembly tool properly.
• Set the frame assembly aside.
Cap Nut
Indented
Side Up
Cap Nut
Assembly Tool
Assembled Rear
Wheel
Straight Axle
Rear Wheel
• Turn the frame upside down.
• Insert the straight axle through the axle holes in the rear of
the frame.
Axle Hole Axle Hole
Frame
Straight Axle
Assembly
1
2
3
4
Hubcap
Hubcap
Frame

• Place two pedal hubs on the pedal axle so that the metal
tabs on the pedal axle fit into the slots inside each pedal hub.
Pedal Hub
Pedal Hub
Pedal Axle
Metal Tab
Metal Tab
Slot
• While holding the pedal hubs on the pedal axle, insert the
assembly into the rectangular hole in the front wheel.
Rectangular Hole
Pedal Axle
Pedal Hubs
Front Wheel
5
• Push the pedal hubs in until they are flush with the surface
of the front wheel.
Pedal Hubs
Pedal Hub
Pedal Hub Pedal Axle
• Turn the front wheel assembly over.
• Insert a pedal hub on top of the pedal axle and into the
rectangular hole in the front wheel.
• Insert the remaining pedal hub below the pedal axle and
into the rectangular hole in the front wheel.
• Push the pedal hubs in until they are flush with the surface
of the front wheel.
• Insert a lock washer into the pedal slot. Make sure the
raised tabs on the lock washer are facing the closed or
outside end of the pedal.
• Insert the other lock washer into the other pedal.
Pedal Hubs
Lock Washer
Raised Tabs
Pedal Slot
Closed End
5
8
9
10
6
7
• Place a scrap block of wood under the front wheel assembly.
• Fit a pedal on the pedal axle.
• With the lock washer centered over the pedal axle end, tap
the pedal with a hammer until it is secure.
• Repeat this procedure to attach the other pedal to the other
end of the pedal axle.
Lock Washer
(Inside Pedal)
Pedal Axle
Pedal
11
Assembly

6
• Turn the frame upright.
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the pedal
axle covers face the rear wheels.
• Place the handlebar over the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
Helpful Hint: You may need to rotate the handlebar to align
the holes.
• Insert the #8 x 3" screw into the hole and tighten with a
Phillips screwdriver. Do not over-tighten.
Handlebar
Frame Neck
Fork Post
Pedal Axle Cover
• Place the front wheel assembly between the fork arms so
that the pedal axle fits into the groove at the bottom of
each fork arm.
• Place a pedal axle cover over the pedal axle on one
fork arm.
• Insert two #8 x 3/4" screws into the pedal axle cover and
tighten with a Phillips screwdriver. Do not over-tighten.
• Repeat this procedure to attach the other pedal axle cover
to the other fork arm.
Fork Arms
Pedal Axle
Groove
Pedal Axle Cover
#8 x 3/4" Screw – 4
SHOWN ACTUAL SIZE
#8 x 3" Screw – 1
SHOWN ACTUAL SIZE
• Position the seat upside down.
• Fit the small pegs on the seat retainer into the holes in
the seat.
One-time assembly is now complete.
• Insert and snap the gas cap into the hole in the frame.
Gas Cap
13
12
14
15
Assembly
Seat Retainer
Seat
Peg
Holes

7
• At an angle, insert the tabs on the seat into any of the top
three sets of slots for the lower, middle or upper position.
• Lower the seat so that the seat retainer inserts and snaps
into the slots in the frame.
• Pull up on the seat to be sure it is secure.
Seat
Helpful Hint: The seat can be attached to the frame in any
of three positions, depending on the size of your child.
Check your child’s fit on the Grow-With-Me Trike by observ-
ing the seat to pedal distance, as it is being ridden. If the
pedals seem too far away or too close for your child, move
the seat up or down.
Attaching the Seat
Proper label application will help to keep the labels looking
their best!
• Wash your hands before applying the labels.
• Make sure the areas where the labels will be applied are
clean and dry. Wipe your vehicle with a clean, soft, dry
cloth to remove any dust or oils.
• For best results, avoid applying a label more than once.
• Apply the labels as shown in the illustration above.
• After applying a label, rub the label firmly with a cloth to
make sure the label is adhered to your vehicle.
Label Decoration
Lower Position Middle Position Upper Position
Tabs
Slots
Seat
Retainer
1
2
3
4
5
6
6

8
• Check the plastic parts regularly and if broken or cracked,
dispose of them properly.
• Check all fasteners regularly to be sure they are tight. If
the fasteners are not tight, tighten them as necessary.
• To clean the Grow-With-Me Trike, use a mild soap and
water solution and a clean cloth. Rinse clean with water to
remove soap residue.
Seat Retainer Tab
• Turn the frame on it’s side.
• Squeeze the seat retainer tabs toward one another and lift
the seat from the frame.
Maintenance
If you have any questions about this product:
In Canada, call 1-800-567-7724, or write to: Mattel Canada Inc, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
In Great Britain, telephone [phone].
In Australia, Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812
(valid only in Australia).
Removing the Seat
Seat Retainer Tab
Frame
Seat