Fisher Scientific 88861047 User manual

Multi Function Rotator Operations Manual
V1 12/05/17

This manual covers the model shown below
88861047
88861048
1
NA Model Voltage Description
100~240V
100~240V Multi Function Rotator US plug
Multi Function Rotator Intl plug
EU Model
N/A
15514080

2
Caution all internal adjustments and maintenance must be performed by qualified
service personnel.
Material in this manual is for information purposes only. Fisher Scientific is
committed to a continuing program of product development and improvement, and
reserves the right to change information, such as specifications, appearance, and
dimensions, described in this document without notice. Fisher Scientific makes no
representations or warranties with respect to this manual. In no event shall Fisher
Scientific be held liable for any damages, direct or incidental, arising out of or
related to the use of this manual.
No part of this manual may be reproduced or transmitted in any form or by any
means, including photocopying, recording, or using information storage and
retrieval systems, for any purpose other than the purchaser's own use, without the
express written permission of the manufacturer.
Any other product names and services identified in this manual are trademarks or
registered trademarks of their respective owners. No such use, or the use of any
trade name, is intended to convey endorsement or other affiliation with Fisher
Scientific.
2017 Fisher Scientific. All rights reserved.
Before using this product, read this entire operation manual
carefully. Users should follow all of the operational guidelines
contained in this manual and take all necessary safety
precautions while using this product. Failure to follow these
guidelines could result in potentially irreparable bodily harm
and/or property damage.

3
Contents
Section 1 Inspection and Installation
Packing List
Connections
Structure Diagram
Section Overview
Specifications
Environmental Conditions
Safety Instructions
Capacity and Speed
Section 3 Operation
Control Panel
Settings
Section 4 Safety Tips and Maintenance
Section 5 Troubleshooting
Section 6 Optional Accessories/Spare Parts
Section 7 Warranty
2
Installation
4
4
4
4
5
5
5
5
6
7
7
7
7
9
10
11
12

Section 1 Inspection and Installation
1. Inspect package and contents upon receipt of the instruments.
If the package is severely damaged or if there are any missing
pieces, please contact the manufacturer immediately.
2. Unpack the instrument, ensure all parts of the instrument and
accessories are not missing or damaged. Make sure to take out
all the components before discarding the packing. If there are
any missing or damaged pieces, please contact the
manufacturer immediately.
3. Place the instrument on a level and firm surface to avoid
vibration and noise.
4
General Power Adaptor
US Plug
CN Plug
EU Plug
UK Plug
*Has been installed on the instrument
1.1 Packing List
Table -1 Packing List
NA Cat.No. NA/EU Cat.No.
88861047
US plug
1
10
N/A
N/A
N/A
Multi Function Rotator
6
1
1
88861048
/15514080
Intl plug
10
1
N/A
6
1
1
1
1
Figure
1.2 Connections
Main Body
Power Cable
Power Adaptor
1.3 Structure Diagram
*Dimpled Rubber Mat
*Screw for Rubber Strip
Rubber Strips
Tray
House
Control Panel
Foot (4)
Top Plate
Dimpled rubber mat
Screw for Rubber
Strip-M4 8(10)×
Description

5
2.1 Specifications
Section 2 Overview
Power Supply
AC100~240V, 50Hz/60Hz, 0.1A
Requirement
Load
Max Load at Centered
Position 1kg(2.2lb)
Weight
Net Weight 7.1Kg(15.6lb)
9.1Kg(20.2lbs)Gross Weight
﹤55dB with no load
ROHS, WEEE, cCSAus, CE Mark
Noise Level
Certificate
Others
5 to 100rpm
0 to 360°
0 to 5°
LED
7°
1rpm
Speed Range
Pendulum Angle
(Reciprocal Mode)
Rotating Angle
(Vibrate Mode)
Display Mode
Tilt Angle Range
Display Accuracy
Speed Accuracy ±1 rpm
Speed and Angle
Note: Maximum speed/tilt angle may vary with heavy or
unbalanced loads.
Time
0 to 250 seconds
0 to 125
Set Cycle No. to 0
1 99min to h59min
Orbital Mode/
Reciprocal Mode
Cycle Index
Continuous Operation
Timing Range
Vibrate Mode 0 to 5 seconds
Size
23mm(0.9in)
316 276 mm(12.4 10.9 in)× ×17 × ×0.7
536 501 346mm(21.1 19.7 13.6in)× × × ×
Orbit Diameter
Tray Dimensions
Package Dimensions
Overall Dimensions 415×293×237mm(16.3×11.5×9.3in)
2.2 Environmental Conditions
WARNING DO NOT use the
in a hazardous atmosphere or with
hazardous materials for which the unit was
not designed. Also, the user should be
aware that the protection provided by the
equipment may be impaired if accessories
used are no provided or recommended by
the manufacturer, or are used in a manner
not specified by the manufacturer.
CAUTION ! To avoid electrical shock,
completely cut off power to the unit by
disconnecting the power cord from the unit
or unplug from the wall outlet. Disconnect
unit from the power supply prior to
maintenance and service. Any spills should
be removed promptly. Bio hazard spills
should be cleaned using approved liquid
promptly. Solvent spills are a fire hazard.
Stop the unit immediately, and DO NOT
operate until clean up is complete and
vapors have dissipated.
Multi Function
Rotator
DO NOT immerse the unit for cleaning.
DO NOT operate the unit if it shows signs of
electrical or mechanical damage.
Please read the entire instruction manual before
operating the Multi Function Rotator.
2.3 Safety Instructions
Application Environmental Conditions: indoor use
Storage Environmental Conditions
5 to 40℃（41 to 104℉）
20% to 85%,
Temperature
Humidity
Altitude
Voltage Fluctuation ±10% of the nominal voltage
≤2,000 m
Temperature
Humidity 20 to 90 non-condensing% %,
NA Cat.No. NA/EU Cat.No.
88861047
US plug
Multi Function Rotator
88861048
/15514080
Intl plug
Description
Category Number

6
Warning: It may affect normal operation of the
instrument and even cause damage if loads are
placed asymmetrically.
Symmetrical placement
Asymmetrical placement
Cornered placement
Sided placement
Other placement
2.4 Capacity and Speed
Position of Loads
Place the loads in the recommended positions below:
1. Place load at the center of the tray
2. Place loads symmetrically around the center of the tray
3. Make sure to use rubber strips to fasten containers onto
the tray
Centered placement
Application areas of this Multi Function Rotator include gel
colorization / decolorization, sample cleaning, antibody
staining,hybridization, immunoprecipitation, blot, and small
volume tissue culture.
Warning: The rotation speed is inversely proportional to
the load. When the instrument is in operation, it is
recommended to adjust the rotation speed from low to
high, step by step and run the instrument at an appropriate
speed to avoid spillage of liquids.
For your safety, please always using rubber strip to hold
samples.
≤30/40
≤225
≤450
≤400
≤600
≤800
Cell Culture Flask
(cm2)
Capacity
(ml)
Max Speed
(rpm)
25
75
150
175
225
100
100
100
100
100
80

Vi b r ate
The front panel of the contains all the controls needed to operate the unit.Multi Function Rotator
① ② ③ ④⑤
This chapter covers the control panel and its operation.
Section 3 Operation
3.1 Control Panel
7
11 12
⑩⑥ ⑦ ⑧ ⑨
1. LED Display Window 1: Shows rotation speed or rotation
angle.
2. LED Display Window 2: Shows time or cycle index.
3. Vibrate Indicator Light: The instrument is in Vibrate Mode
when this light is on.
4. Cycle Indicator Light: The loop function is in use when this
light is on.
5. Orbital Indicator Light: The instrument is in Orbital Mode
when this light is on.
6. Reciprocal Indicator Light: The instrument is in Reciprocal
Mode when this light is on.
7. Mode Button: Press this button to choose operation mode
needed.
8. UP Arrow Button 1: Press this button to increase rotation
speed or angle.
9. DOWN Arrow Button 1: Press this button to decrease
rotation speed or angle.
10. UP Arrow Button 2: Press this button to increase time or
cycle value.
11. DOWN Arrow Button 2: Press this button to decrease time
or cycle value.
12. Start/Stop Button: Press this button to start/stop the
instrument.
7
Introduction of Operation Modes
Orbital Mode
1. Horizontal tilt angle 7°, continuous 360° rotating
around the axis.
2. Rotation speed range: 5-100 rpm, continuously
adjustable.
3. Timer range: 0-250 seconds, if set to 0, the
instrument is not operating in this mode.
Reciprocal Mode:
1. Horizontal tilt angle 7°, rotating around the axis.
2. Pendulum angle range: 0-360°, can be adjusted by
every 30°.
adjustable.
4. Timer range: 0-250 seconds, if set to 0, the
instrument is not operating in this mode.
Vibrate Mode:
1. Horizontal tilt angle 7°, rotating around the axis.
2. Pendulum angle range: 0-5°, can be adjusted by
every 1°.
3. Timer range: 0-250 seconds, if set to 0, the
instrument is not operating in this mode.
Operation Cycle:
Each operation cycle is composed by two or more
operation modes. The number of cycles can be
between 0 to 125. When number of cycle is set to
0, the instrument will operate in continuous mode.
3. Rotation speed range: 5-100 rpm, continuously
3.2 Installation
1. Connect all the components according to the figures
shown on page 4 of this manual. Use grounded power
outlet.
2. Press down the power switch on the back right side of
the instrument and put it to the “|” state and then the
instrument is in standby.

Power Recovery
If the power supply is cut off suddenly while the
instrument is in operation, the unit will automatically run
at the previously set parameter upon power restoration.
The display window will flash. Press any button to stop
flashing.
8
Table of Mode Combinations
ON
ON
ON
ON
ON ON
ON
ONON ON
ON
OFF
OFF
OFF OFF
OFF
OFF
WAIT WAIT
WAIT
WAIT
WAIT
8910 11 12 13 14
ON
OFF
ON
OFF
WAIT
OFF
ON
OFF OFF
ON
Reciprocal
ON
ON
ON
Orbital
Vibrate
1 2 3456 7
Reciprocal
Orbital
While operating in timer mode, the instrument will stop
running automatically when the timer goes off and the
alarm will sound.
After the operation is finished, please press the power
switch at the back right side the instrument and put it
into the “O” state. Unplug the instrument and store the
instrument according to the storage guide.
Finish Operation
Alarm System
ONONONOFF OFFWAITWAIT
Vibrate
3.3 Settings
1. Single mode continuous operation 1.1 Press “ ”to select
operation mode needed and the corresponding indicator
light will be on. Press “ ” or “ ” on the left to set
rotation speed and angle needed in the left-hand-side LED
display window. (Press “ ” to switch settings between
speed and angle).
1.2 Press “ ”or “ ” on the right to set any time.
1.3 Press “ ” until Cycle Indicator Light is on. Press“ ”
on the right to decrease the time to 0.
1.4 Press “ ” to start operation.
1.5 Press “ ” again to end operation.
2. Single mode timed operation
2.1 Press “ ”to select operation mode needed and the
corresponding indicator light will be on. Press “ ” or “ ”
on the left to set rotation speed and angle needed in the
left-hand-side LED display window. (Press “ ” to switch
settings between speed and angle)
2.2 Press “ ”or “ ” on the right to set time needed.
2.3 Press “ ”again until Cycle Indicator Light is on. Press “ ”
or “ ” to set the required number of cycles which is between
0-125. (Timer range is the product of set time and number of
cycles. The maximum time that can be set is 250 ×125 =31250
seconds.)
2.4 Press “ ”to start operation.
2.5 Press “ ”o end operation.
3.Multi-mode continuous operation
3.1 Press “ ” to select operation mode needed and the
corresponding indicator light will be on. Press “ ”or “ ”
on the left to set rotation speed and angle needed in the left
-hand-side LED display window. (Press “ ” to switch settings
between speed and angle)
3.2 Press “ ”or “ ” on the right to set time needed.
3.3 After setting one operation mode, press “ ” again to
switch to another mode indicated by the corresponding
indicator light and repeat step 3.1, 3.2 to set corresponding
parameters.
3.4 Combination of 2-3 operation modes is allowed. (When
the time is set to 0, the procedure will skip the corresponding
mode during operation.)
3.5 Press “ ” until the Cycle Indicator Light is on. Press
“ ”or “ ” on the right to decrease the number of cycles
to 0.
3.6 Press “ ” to start operation.
3.7 Press “ ” to end operation.
4. Multi-mode timed operation
4.1 Press “ ”to select operation mode needed and the
correspon-ding indicator light will be on. Press “ ” or “ ”
on the left to set rotation speed and angle needed in the left
-hand-side LED display window (Press “ ” to switch settings
between speed and angle).
4.2 Press “ ”or “ ” on the right to set time needed.
4.3 After setting one operation mode, press “ ”again to
switch to another mode indicated by the corresponding
indicator light and repeat set 4.1, 4.2 to set corresponding
parameters.
4.4 Combination of 2-3 operation modes is allowed. (When
the time is set to 0, the procedure will skip the
corresponding mode during operation.)
4.5 Press “ ” until the Cycle Indicator Light is on. Press
“ ”or “ ” on the right to set the number of cycles
between 0-125.
4.6 Press “ ” to start operation.
4.7 Press “ ” to end operation.

Section 4 Safety Tips and Maintenance
Safety Tips
1. Use independent power supply.
2. Check if the local power supply voltage is suitable for use.
3. Do not drag the power supply cable when unplugging.
4. Do not use non-specified power cable or damage cable.
5. Service should only be performed by a qualified
professional.
6. The power supply must be unplugged under the following
situations:
a. When the unit is moved
b. When the electrical cabinet or the moving component is
opened
c. When the equipment is malfunctioning
d. When the equipment is not in use
Maintenance
a. This instrument uses brushless DC motor. It is
maintenance free and has a long service time, high
quality, and low noise level.
b. Surface can be cleaned with a mild detergent and water.
If accidental spillage of liquids caused by mishandling or
contained breakage occurs on the surface of the
instrument, please shut down the instrument and clean
up the liquid immediately.
If the liquid has already spilled into the unit, cut off the
power supply first and immediately clean up the liquid
at the surface of the instrument. Place the instrument in
a ventilated and dry environment for 24 hours before
reuse. If the instrument is not functioning after drying
for 24 hours, please contact the manufacturer.
Warning: Disassembling/Assembling without a
qualified professional's guidance may cause
malfunctioning of the instrument.
Clean Spill
9

Section 5 Troubleshooting
Please refer to the following table to troubleshoot if any malfunction occurs. If the problem still exists, contact your local
sales representative.
Error
Cannot start machine,
LED display window off
No shaking of the tray
Loud noise
Other
Cause
Power disconnected
Power switch off
Power adaptor failure
Over-weighted or unbalanced load
Electrical malfunction
Mechanical malfunction
Tray loose
Load moving
Machine case loose
Keep record for maintenance
Solution
Connect the power
Turn power switch on
Replace power adaptor
Adjust the weight and position of load,
decrease rotation speed
Contact Fisher Scientific
Contact Fisher Scientific
Fasten tray screws
Change silicone pad or fasten load
Fasten machine case screws
10

Section 6 Optional Spare Parts
General Power Adaptor
298×258mm
Dimpled Rubber Mat
AC 100 240V, 50/60HZ~
125VAC, 10A, 1.8m
250VAC, 10A, 1.8m
250VAC, 16A, 1.8m
250VAC,13A, 1.8m
88861158
88861157
88861156
88861155
88861154
88861198
Rubber Strips 88861178
88861199
180×7mm (6pcs/pack)
M4×8 (8pcs/pack)
Power Cable US Plug
Power Cable CN Plug
Power Cable EU Plug
Power Cable UK Plug
Screw for Rubber Strip
Description NA Cat. No. EU Cat. No. Dimensions Figure
Max. Qty
1
5
1
1
1
1
1
10
11
15594130
15594120
15554120
N/A
N/A
15564120
15574120
15504140

When used in laboratory conditions and according to these operation instructions and maintenance, this product is
warranted for 24 months against defective materials or workmanship. The 24 month warranty period begins from the
delivery date of this product.
For product quality or performance issues, contact Fisher Scientific Customer Service.
Section 7 Warranty
12

United States
1-800-766-7000
fishersci.com
Austria:
[phone]
at.fishersci.com
Belgium:
[phone]
be.fishersci.com
Denmark:
[phone]
fishersci.dk
Germany:
[phone]
de.fishersci.com
Ireland:
[phone]
ie.fishersci.com
Italy:
[phone]
it.fishersci.com
Finland:
[phone]
fishersci.fi
France:
[phone]
fishersci.fr
North America
Canada
1-800-234-7437
fishersci.ca
Netherlands:
[phone]
nl.fishersci.com
Norway:
[phone]
fishersci.no
Portugal:
[phone]
pt.fishersci.com
Spain:
[phone]
es.fishersci.com
Sweden:
[phone]
fishersci.se
Switzerland:
[phone]
ch.fishersci.com
UK:
[phone]
fisher.co.uk
Europe
Find out more at
fishersci.com