Fisher Scientific 88861041 User manual

Nutating Mixer Fixed Speed
Nutating Mixer Variable Speed
3D Platform Rotator
Catalog Number:
88861041
88861042
88861043
88861044
88861045
88861046
Instruction Manual

ⅰ
Section 1 Inspection and Installation
Section Overview2
Section 3 Operation
Section 4 Safety Tips and Maintenance
Section 5 Troubleshooting
Section 6 Optional Accessories/Spare Parts
Section 7 Warranty
Packing List
Connections
Structure Diagram
Specifications
Operation of the Control Panel
Settings
Environmental Conditions
Safety Instructions
Loads and Speed
1-1
1-2
1-3
1-4
2-1
2-1
2-2
2-3
2-5
7-1
6-1
5-1
4-1
3-2
3-1
3-1
Table of Contents
ⅱ
Fisher Scientific Nutating Mixer/3D Platform Rotator Fisher Scientific Nutating Mixer/3D Platform Rotator
Important before using this product, read this entire operation
manual carefully. Users should follow all of the operational
guidelines contained in this manual and take all necessary safety
precautions while using this product. Failure to follow these
guidelines could result in potentially irreparable bodily harm
and/or property damage.
Caution all internal adjustments and maintenance must be performed by qualified
service personnel.
Material in this manual is for information purposes only. Fisher Scientific committed
to a continuing program of product development and improvement, and reserves
the right to change information, such as specifications, appearance, and
dimensions, described in this document without notice. Fisher Scientific makes no
representations or warranties with respect to this manual. In no event shall Fisher
Scientific be held liable for any damages, direct or incidental, arising out of or
related to the use of this manual.
No part of this manual may be reproduced or transmitted in any form or by any
means, including photocopying, recording, or using information storage and
retrieval systems, for any purpose other than the purchaser's own use, without the
express written permission of the manufacture.
Any other product names and services identified in this manual are trademarks or
registered trademarks of their respective owners. No such use, or the use of any
trade name, is intended to convey endorsement or other affiliation with Fisher
Scientific.
@2015 Fisher Scientific. All rights reserved.

Fisher Scientific
Cat.No
3D
Platform
Rotator
US plug
3D
Platform
Rotator
Interna
-tional
plug
Nutating
Mixer
Fixed
Speed
120V
Nutating
Mixer
Fixed
Speed
230V
88861041 88861043
Model
US Plug
CN Plug
EU Plug
UK Plug
N/A
N/A
N/A
Screw for
Rubber
Strip
88861042
Nutating
Mixer
Speed
US
Variable
Nutating
Mixer
Speed
Variable
Interna
-tional
88861044 88861045 88861046
1
1
N/A
N/A
N/A N/A
N/A
N/A N/A
N/A
N/A
1
1
1
1
N/A
N/A
1
1
1
1
Fuse N/A N/A
N/A N/A
22
Ceneral
Power
Adaptor
Nutating Mixer/3D Platform Rotator
1. Inspect package and contents upon receipt of the instruments. If the
package is severely damaged or if there are any missing pieces, please
contact the manufacturer immediately.
2. Unpack the instrument, ensure all parts of the instrument and accessories
are not missing or damaged. Make sure to take out all the components before
discarding packing. If there are any missing or damaged pieces, please
contact the manufacturer immediately.
3. Place the instrument on a level and firm surface to avoid vibration and
noise.
4. This is the general user manual for three instruments. Please make sure
to refer to the corresponding chapter for your instrument.
Section 1 Inspection and Installation 1.1 Packing List
Table -1 Packing List
Section 1
Inspection and Installation
1-1Fisher Scientific 1-2
Nutating Mixer/3D Platform Rotator
11
1
1
1
1
1
1
1
1
1
1
10 10 10 10 10 10
6 6
6
6
6
6
Dimpled
Rubber
Mat
Rubber
Strips

Nutating Mixer Fixed Speed
Nutating Mixer Variable Speed/3D Platform Rotator
Machine
1.2 Connections 1.3 Structure Diagram
Section 1
Inspection and Installation
Section 1
Inspection and Installation
Power Cable
Power Cable
Machine
Power Adaptor
Foot(4)
Control Panel
House
Tray
Dimpled Rubber
Mat
1-31-4
Screw for Rubber
Strip-M4×8(10)
Fisher Scientific Nutating Mixer/3D Platform Rotator Fisher Scientific Nutating Mixer/3D Platform Rotator

Note: Maximum speed/tilt angle may vary with heavy or unbalanced loads.
0 360 to °
LED
0.8kg
415 293 273mm
(16.3×11.6×10.7in.)
× ×
1rpm
LED
306 10.5in.)× ×266mm(12.0
415 295 170mm
(16.3
× ×
×11.6×6.7in.)
3D Platform Rotator
3D Platform Rotator
3D Platform Rotator
3D Platform Rotator
2 60 to rpm 2 80 to rpm
20°7°
1 99min to h59min
Nutating Mixer
Fixed Speed
Nutating Mixer
Variable Speed
Nutating Mixer
Fixed Speed
Nutating Mixer
SpeedVariable
88861041 88861042 88861043 88861044 88861045 88861046
24rpm 20rpm
536 19.7 13.6in.)× × × ×501 346mm(21.1
±1rpm
Nutating Mixer
Fixed Speed
Nutating Mixer
SpeedVariable
±1°
Nutating Mixer
Fixed Speed
Nutating Mixer
SpeedVariable
2.1 Specifications
Section 2 Overview
Rotation Speed
Product Name
Speed Range
Display Mode
Display Accuracy
Speed Accuracy
Angle
Product Name
Tilt Angle
Tilt Angle Accuracy
Rotation Angle
Load
Maximum Load
(Centered on tray)
Time
Product Name
Timer Range
Display Mode
Size
Product Name
Tray Dimensions
Package Dimensions
2-12-2
Cat. NO.
ROHS, WEEE, cCSAus, CE Mark
5 to 40 ℃（41 to 104 ℉）
0 to 60 ℃ （36 to 124 ℉ ）
20% to 85%,
3D Platform Rotator
5.9kg(13lb)
8.6kg(18.9lb)
Nutating Mixer
Fixed Speed
Nutating Mixer
SpeedVaraioable
7.4kg(16.3lb) 7.3kg(16.1lb)
9.4kg(20.7lb) 9.3kg(20.5lb)
Weight
Product Name
Net Weight
Gross Weight
Others
Noise Level
Certificate
﹤ dB with no load when ambient noise is 45 dB55
Application Environmental Conditions: indoor use
Temperature
Humidity
Altitude
Voltage Fluctuation ±10% of the nominal voltage
≤2,000 m
Storage Environmental Conditions
Temperature
Humidity 20％ to 90％, non-condensing
2.2 Environmental Conditions
Section 2
Overview
3D Platform Rotator
Nutating Mixer
Fixed Speed
Nutating Mixer
Variable Speed
88861041 88861042 88861043 88861044 88861045 88861046
Product Name
Cat. NO.
110V,60z,
0.1A
220V,50Hz,
0.05A
100~240V,
50Hz/60Hz,1A
100~240V,
50Hz/60Hz, 0.8A
Requirement
Power Supply
Fisher Scientific Nutating Mixer/3D Platform Rotator Fisher Scientific Nutating Mixer/3D Platform Rotator
Overall Dimensions

Symmetrical Placement
Asymmetrical Placement
Cornered Placement Sided Placement
Other Placement
Asymmetric loading or unloading may affect the normal operation of the
instrument and may even cause unpredictable damage.
Section 2
Overview
Section 2
Overview
2-32-4
WARNING DO NOT use the in a
hazardous atmosphere or with hazardous materials for which the unit was
not designed. Also, the user should be aware that the protection provided
by the equipment may be impaired if accessories used are not
provided or recommended by the manufacturer, or are used in a
manner not specified by the manufacturer.
CAUTION ! To avoid electrical shock, completely cut off power to the
unit by disconnecting the power cord from the unit or unplug from the
wall outlet.
Disconnect unit from the power supply prior to maintenance and
service. Any spills should be removed promptly. Biohazard spills
should be cleaned using approved liquid promptly. Solvent spills are a
fire hazard. Stop the unit immediately, and DO NOT operate until
clean up is complete and vapors have dissipated.
Nutating Mixer/3D Platform Rotator
DO NOT immerse the unit for cleaning.
DO NOT operate the unit if it shows signs of electrical or mechanical
damage.
Please read the entire instruction manual before operating the Nutating
Mixer/3D Platform Rotator.
2.3 Safety Instructions
Place the loads in the recommended positions below:
1. Place load at the center of the tray
2. Place loads symmetrically around the center of the tray
3. Make sure to use rubber strips to fasten containers onto the tray
Position of Loads
Centered Placement
Fisher Scientific Nutating Mixer/3D Platform Rotator Fisher Scientific Nutating Mixer/3D Platform Rotator

Nutating Mixer Variable Speed
3D Platform Rotator
25
25
75
75
150
150
175
175
225
225
30/40
30/40
225
225
450
450
600
600
800
800
60
80
60
80
60
80
60
80
The front panel of the
contains all the controls needed to operate the unit.
Nutating Mixer Variable Speed/3D Platform Rotator
Nutating Mixer Variable Speed/3D Platform Rotator
2.4 Loads and Speed
Cell Culture Flask
Specification(cm2)
Cell Culture Flask
Specification(cm2)
≤Capacity（ml）
≤Capacity（ml）
Maximum Speed
（rpm）
Maximum Speed
（rpm）
Warning: The rotation speed is inversely proportional to the load. When
the instrument is in use, it is recommended to adjust the rotation speed
from low to high, step by step and run the machine at an appropriate speed
to avoid accidental spillage of liquids.
For safety, please always using rubber strip to hold samples in place.
Section 2
Overview
TIME
①
②
③④
⑤⑥
This Chapter covers introduction of the control panel and its operation.
1. Start/Stop button: Start or stop the instrument
2. RUN indicator light: The light is on when the instrument is running and
off when the instrument is in standby.
3. TIME display window: The window shows cumulative time (in continuous
mode) or remaining time (in timer mode). The range of time displayed is 0
to 99 hours and 59 minutes. The accuracy is 1 minute.
4. SPEED display window: The window shows set speed (when the instru
-ment is in standby) or current speed (when the instrument is running).
5. Set Time Buttons: UP/DOWN Arrow buttons are used to increase/
decrease the set time of the instrument.
. Set Speed Buttons: UP/DOWN Arrow buttons are used to increase/
decrease the set speed of the instrument.
6
Section 3 Operation
3.1 Operations of the Control Panel
2-53-1
6 0
8 0
.
Fisher Scientific Nutating Mixer/3D Platform Rotator Fisher Scientific Nutating Mixer/3D Platform Rotator

Nutating Mixer Fixed Speed
Nutating Mixer Fixed Speed
①
Nutating Mixer Variable Speed/3D Platform Rotator
1. Connect all the components according to the figures shown on page 1-3
of this manual. Use grounded power outlet.
2. Press power button on the back right side of the instrument and put it
to the “|” state and then the instrument is in standby.
Preparation
1.RUN indicator light: The light is on when the instrument is running.
3.2 Settings
Time Settings
1. Continuous mode
Press the “ ” or “ ” arrow button below the TIME display window. When
the number shown on the display window starts flashing, press “ ” arrow
button to decrease the time to 00:00 and then release the button. The time
setting is finished after the number shown on the display window has
flashed twice.
2. Timer mode
Press the “ ” or “ ” arrow button below the TIME display window. When
the number shown on the display window starts flashing, press “ ” or “ ”
arrow button to increase or decrease the time value. Release the button
when the time shown on the display window reaches the set value. The time
setting is finished after the number shown on the display window has
flashed twice.
Speed Settings
Press the “ ” or “ ” arrow button below the SPEED display window.
When the number shown on the display window starts flashing, press “ ”
or “ ” arrow button to increase or decrease the speed value. Release the
button when the speed shown on the display window reaches the set value.
The speed setting is finished after the number shown on the display window
has flashed twice.
Note: press the “ ” or “ ” arrow button for a longer time to accelerate
the setting.
Run and Stop
1. Continuous Mode
Press button and the instrument will start running with the specified
settings and the RUN indicator light will be on. The TIME display window
will show the cumulative time and the SPEED display window will show the
current speed. Press “ ”button again and the instrument will slow down
until it stops. The instrument will then be in standby and the two display
windows will show the set values.
“ ”
2. Timer Mode
Press button the instrument will start running with the specified
settings and the RUN indicator light will be on. The TIME display window
will show the remaining time and the SPEED display window will show the
current speed. Press button again and the instrument will slow down
until it stops. The instrument will then be in standby and the two display
windows will show the set values.
“ ”
“ ”
Turn the power switch to “|” position. The RUN indicator light will be on and
the instrument will start rotating at the fixed speed.
Section 3
Operation
Section 3
Operation
3-23-3
Fisher Scientific Nutating Mixer/3D Platform Rotator Fisher Scientific Nutating Mixer/3D Platform Rotator

If the power supply is cut off suddenly while the instrument is in operation,
the unit will automatically run at the previously set parameter upon power
restoration. The display window will flash. Press any button to stop flashing.
Finish Operation
After the operation is finished, please press the power switch at the back
right side the instrument and put it into the “O” state. Unplug the instrument
and store the instrument according to the storage guide.
Alarm System
When the normal operation is obstructed or stopped by malfunctioning,
the instrument will stop running automatically within 2 minutes and the
alarm will sound.
Power Recovery
Section 3
Operation
Section 4 Safety Tips and Maintenance
Safety Tips
1. Use independent power supply.
2. Check if the local power supply voltage is suitable for use.
3. Do not drag the power supply cable when unplugging.
4. Do not use non-specified power cable nor damage cable.
5. Service should only be performed by a qualified professional.
6. The power supply must be unplugged under the following situations:
a. when the unit is moved
b. when the electrical cabinet or the moving component is opened
c. when the equipment is malfunctioning
d. when the equipment is not in use
a. This instrument uses a high-accuracy motor. It is maintenance free and
has a long service time, high quality, and low noise level.
b. Surfaces can be cleaned with a mild detergent and water.Liquid is not
allowed inside the dust cover.
c. Two fuses are installed inside the power socket at the back of the Nutating
Mixer Fixed Speed (One is for work and the other is for backup). The
installation of the fuses is shown in the figure below:
Maintenance
Warning: Avoid dripping detergent or water into the instrument during cleaning.
3-44-1
Fisher Scientific Nutating Mixer/3D Platform Rotator Fisher Scientific Nutating Mixer/3D Platform Rotator

Section 5 Troubleshooting
Error
No shaking of the tray
Loud noise
Other
Cause
Power disconnected
Switch off
Power adaptor failure
Over-weighted or
unbalanced load
Electrical
malfunction
Mechanical
malfunction
Keep record for maintenance
Solution
Connect the power
Switch on
Replace power adaptor
Adjust the weight and
position of load,
decrease rotation speed
Contact Fisher Scientific
Contact Fisher Scientific
Cannot start machine,
LED display window
off
Load moving
Tray loose
House loose
Change Dimpled Rubber
Mat or fasten load
Fasten fixing screws on the
tray
Fasten fixing screws at the
House
Section 4
Safety Tips and Maintenance
4-25-1
If accidental spillage of liquids caused by mishandling or contained break
-age occurs on the surface of the instrument, please shut down the
instrument and clean up the liquid immediately.
If the liquid has already spilled into the unit, please cut off the power
supply first and immediately clean up the liquid at the surface of the
instrument. Then place the instrument in a ventilated and dry environment
for 24 hours before reuse. If the instrument is still not functioning after
drying for 24 hours, please contact the manufacturer.
Warning: Disassembling/Assembling without a qualified professional's
guidance may cause malfunctioning of the instrument.
Clean Spill
Please refer to the following table to troubleshoot if any malfunction occurs.
If the problem still exists, contact your local sales representative.
Fisher Scientific Nutating Mixer/3D Platform Rotator Fisher Scientific Nutating Mixer/3D Platform Rotator