Flavor Burst FB 80M Series User manual

This manual is for the exclusive use of licensees and employees of McDonald’s Corporation.
©2017 Flavor Burst Company Printed in September Printed in
All Rights Reserved The United States of America
Flavor Burst™ Soft-Serve Unit
Model FB 80M-08
Model FB 80M-26
Manufactured exclusively for
McDonald’s ® by
Flavor Burst Company
499 Commerce Drive
Danville, IN 46122
For general information and to locate a
distributor near you, call or visit our website:
Phone: [phone]
Toll Free Number: [phone]
Fax: [phone]
www.flavorburst.com
For pricing, ordering and support, contact one
of our qualified distributors.
Warranty
An installation and warranty form is provided with every FB 80M system, located inside the FB 80M unit with this manual. It
is important that the operator carefully review the warranty and installation documents accompanying the unit before using
this system. Any questions or concerns regarding the warranty should be clarified upon delivery or installation. For more
information, contact your local authorized Flavor Burst distributor.
Table of Contents
Introduction………………….……...……………………….……………………….…….….….………1
Safety Precautions……………………………..………………….………..…….……….…….....……1
Parts Identification/Function……...……………………………….……..…...………………………...4
Daily Opening Procedures……..………………………………….…….…..…….……………….….21
Daily Closing Procedures………………………………………….………..……….……….……….25
Replacing the Syrup Flavors……………………………………………………………..……….…..29
Scheduled Maintenance…………...………………………………………..…….………...……..….33
Equipment Setup…..………………………………………………………...…..…..….………….….49
Keypad Operations……………….……………………………………………..…………..….…...…65
Troubleshooting Guide……………….………………………………………..…..……………….….71
Directory of Cleaning Procedures……………………………………………..….……..………..….76
Parts Replacement Schedule………...…………………………….…………...….……..……….…77
Alternate Parts and Kits by Freezer Model……………………………………...…..…..…………..78
Ordering/Service Information…………….…….……………………………………………..……...79
Wiring Diagram……………………………..……………………………………..………………...….80

1
INTRODUCTION
Congratulations on your purchase of an
FB 80M series flavoring system! As a food and
beverage provider, your customers are your
greatest asset. Your primary concern must be
the health and welfare of your customers. This
manual provides everyday operating guidelines
and procedures. Special functions have been
incorporated into the equipment to provide
simple and effective cleaning and sanitizing of
your unit. We urge you to follow these
instructions carefully and maintain strict sanitary
practices in your daily operating routine.
The FB 80M series system is an add-on to a
soft-serve freezer designed to inject
concentrated flavorings throughout soft-serve
product as it is dispensed. To dispense a
flavored product, the operator first selects the
flavor(s) from the system keypad. The draw-
handle must then be pulled completely forward
in a smooth continuous motion to activate the
FB 80M system and dispense flavored product.
Returning the draw-handle to a closed position
will stop product flow and the FB 80M system.
Flavor Burst™ syrup is stored within the
equipment cabinet in 1 gallon disposable bags.
Proper syrup injection rate is maintained by
adjusting the flavor level on the system keypad.
Components of the FB 80M system should be
cleaned daily to ensure the highest standard of
sanitation. When your equipment is delivered
or if it has been unused for more than 24 hours,
follow the DAILY OPENING PROCEDURES.
Always follow these safety precautions when
operating the Flavor Burst system:
DO NOT operate the system without
reading this operator’s manual. Failure to follow
this instruction may result in equipment
damage, poor system performance, health
hazards, or personal injury.
DO NOT operate the system unless it is
properly grounded. Failure to follow this
instruction may result in electrocution.
DO NOT operate the system with larger
fuses than specified on the system data label.
Failure to follow this instruction may result in
electrocution or damage to the machine.
Consult your electrician.
DO NOT put objects or fingers in the
door spout. Failure to follow this instruction may
result in contaminated product or personal
injury from blade contact.
The FB 80M cabinet system must be
placed on a level surface capable of supporting
at least 220 lbs of weight. Failure to comply
may result in personal injury or equipment
damage.
DO NOT place more than 25 lbs of
weight on top of the FB 80M cabinet. Failure to
comply may result in personal injury or
equipment damage.
DO NOT install the unit in an area where
a water jet could be used, and do not use a
water jet to clean or rinse the system. Failure to
follow these instructions may result in serious
electrical shock.
SAFETY PRECAUTIONS

2
HAZARD COMMUNICATION STANDARD
(HCS) – The procedure(s) in this manual
include the use of chemical products. These
chemical products will be highlighted in
bold-faced letters followed by the
abbreviation (HCS) in the text portion of the
procedure. See the Hazard Communication
Standard (HCS) manual for the appropriate
Material Safety Data Sheet(s) (MSDS).
NOISE LEVEL: Airborne noise emission does
not exceed 78 dB(A) when measured at a
distance of 1.0 meter from the surface of the
machine and at a height of 1.6 meters from the
floor.
NOTE: Operations Manual subject to change.
Contact your local distributor for most recent
updates concerning the FB 80M unit.
NOTE: Access to the service area is restricted to persons
having safety / hygiene knowledge and practical
experience of the appliance.
NOTE: This appliance can be used by children aged from
8 years and above and persons with reduced physical,
sensory, or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved.
NOTE: Children shall not play with the appliance.
NOTE: Cleaning and user maintenance shall not be made
by children without supervision.
NOTE: Operate unit under normal ambient
temperatures between 60 and 80 degrees
Fahrenheit. Unit should never be exposed to
freezing temperatures.
ENVIRONMENTAL NOTICES
If the crossed out wheeled bin symbol is affixed to this product, it signifies that this product
is compliant with the EU Directive for Waste Electric/Electronic Goods (WEEE) as well as
other similar legislation in affect after August 13, 2005. Therefore, it must be collected
separately after is use is completed, and cannot be disposed of as unsorted
municipal waste.
The user is responsible for returning the product to the appropriate collection facility, as specified by
your local codes. For additional information regarding applicable local laws, please contact the
municipal facility and/or local distributor.

3
Notes:
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________
_____________________________________

4
General System Overview (See Figure 1)
ITEM PART NO. DESCRIPTION QTY. FUNCTION
1 063196 SWITCH-SPIGOT-STANDARD
FB80 1 Activates Injector Assembly.
2 063201 KEYPAD-FB 2001/2002 FB80 1 Flavor Burst unit command center.
3 063242 BRACKET-MTG.-KEYPAD
ELE 500 1 Mounts the keypad to the freezer.
4 063251 TRAY-PARTS FB80 1 Holds sanitized parts while they air
dry.
5 063233 INJECTOR A.-W/6'TUBE
FLVR BRST 1 Injects syrups into the product.
6 063250 BRACKET-HANGING-
ACCESSORY 1 Stores flavor line and Injector Motor when not in use.
7 063348 2' SURFACE RACEWAY 1 Attaches flavor lines to side of freezer.
8 N/A OUTER CABINET ASSEMBLY 1 Houses inner cabinet assembly.
9 063179 TRAY-FLAVORING FLAVOR
BURST 8 Houses syrup bags.
10 N/A INNER CABINET ASSEMBLY 1 Houses syrup trays and bags.
11 063271 CAP-BOTTLE-SANITIZER FB80 1 Houses sanitizer cleaning solution.
12 N/A SYRUP BAG CONNECTOR
ASSEMBLY 8 Transports syrup from the bag to the pumps.
13 N/A REMOTE MICROPROCESSOR
MODULE 1 Main power supply.
14 063210 CABLE-PUMP-(EXTERNAL)
MCD 1 Links electronics board to pumps.
15 063197 CABLE-POWER #2 FLAVOR
BURST 1 Supplies the electronics board with power.
16 N/A CONNECTOR A.-BAG-MCD
FB80 8 Connects flavor bag to syrup out tube.
17 063273 KIT-SPARE PARTS-INJ 325
SYRUP 1 Houses extra spare parts and wear items.
PARTS IDENTIFICATION/FUNCTIONS

5
General System Overview
26000
13
2
1
3
56
15
14
10
8
11
12
9
7
17
16
4
Figure 1

6
Outer Cabinet (See Figure 2)
ITEM PART NO. DESCRIPTION QTY. FUNCTION
1 063192 PANEL-TOP FLAVOR BURST 1 Covers the top of the inner cabinet.
2 063189 PANEL-LEFT-FLAVOR BURST 1 Covers the left side of inner cabinet.
3 N/A INNER CABINET ASSEMBLY 1 Houses syrup trays and bags.
4 063288 CABINET FRONT DOOR PANEL 1 Front door, allows access to flavor
bags.
5 063195 HANDLE-CABINET-DOOR-
FRONT 1 Allows grip for opening front panel.
6 068120 8-32 X 1/2" PAN HEAD SCREW 2 Fastens handle to front door panel.
7 063258 BUMPER-RUBBER W/WASHER 4 Provides spacing between cabinet
base and table.
8 N/A 10-32 X 1/2" PAN HEAD SCREW 4 Fastens rubber bumpers to cabinet
base.
9 063237 PLUG-SHORT #1672 FB80 4 Covers screw hole in rubber bumper.
10 063191 PANEL-REAR FLAVOR BURST 1 Allows access to pumps.
11 068121 8-32 X 1/4" PAN HEAD SCREW 1 Secures back panel to base.
12 063190 PANEL-RIGHT FLAVOR BURST 1 Covers right side of inner cabinet.
13 065833 FLAVOR BURST LOGO DECAL 1 Displays Flavor Burst trademark logo.

7
Outer Cabinet
3
1
2
12
10
7
13
4
5
9
8
6
11
26001
Figure 2

8
Inner Cabinet (See Figure 3)
ITEM PART NO. DESCRIPTION QTY. FUNCTION
1 063181 COVER-RACK-SYRUP FLAVOR
BURST 1 Keeps side and inner panels stable.
2 063184 PANEL-LEFT-RACK-SYRUP
FLVR BRST 1 Holds outer syrup rails.
3 N/A SYRUP BAG CONNECTOR
ASSEMBLY 8 Transports syrup from the bag to the pumps.
4 063193 RAIL-BOX-SYRUP FLAVOR
BURST 16 Holds flavor trays in place.
5 063180 BRACKET-SUPPORT-TRAY
FLVR BRST 8 Houses flavor line leading to syrup bag.
6 063183 DIVIDER-RACK-SYRUP FLAVOR
BURST 2 Holds inner syrup rails.
7 063182 PANEL-REAR-RACK-SYRUP
FLVR BRST 1 Attaches the rear of the inner and side panels.
8 063236 LINE-FLUSH-SANITIZER FB80 1 Flushes flavor lines with sanitizer
when attached.
9 063188 PANEL-BASE FLAVOR BURST 1 Attaches the bottom of the inner and
side panels.
10 063185 PANEL-RIGHT-RACK-SYRUP
FLVR BRST 1 Holds outer syrup rails.
11 068121 8-32 X 1/4" PAN HEAD SCREWS 46 Fastens pump brackets and pumps.
12 063187 BRACKET-MOUNT-ACC.-EXT
FLVR BRST 1 Secures Accessory Mounting Bracket to cabinet base.
13 063186 BRACKET-MOUNT-ACC. FLVR
BRST 1 Secures pump cable to cabinet base.
14 068119 4/40 LOCK NUTS 4 Secures screws to mount pump cable
face.
15 N/A 4-40 X 3/8" PAN HEAD SCREWS 4 Attaches pump cable face to bracket.
16 063209 CABLE-CABINET-SYRUP
(INTERNAL) 1 Supplies power to the pumps.
17 063194 SHELF-PUMP-SYRUP FLVR
BRST 3 Holds pumps.
18 063274 PUMP-PERISTALTIC-SYRUP
FB80 8 Pumps sanitizer solution to flush tube and sanitizer line.
19 063266 PUMP-PERISTALTIC-SANITIZER 1 Pumps sanitizer solution to flush tube
and sanitizer line.

9
Inner Cabinet
26002
15 11
13
16
14
11 12
1
9
2
6
6
11
18
19
16
4
5
8
3
4
17
11
10
7
Figure 3

10
Injector Assembly and Related Parts (See Figure 4)
ITEM PART NO. DESCRIPTION QTY. FUNCTION
1 063177 ADAPTOR-INJECTOR W/
O-RING 1
Attaches Injector Assembly to freezer
doors of most Taylor Freezer models
& some Crown Series models.
1A 063262 ADAPTOR-O-RING PARKER #2 1 Creates tension to secure Adapter to
freezer door.
1B 063261 GASKET-ADAPTOR-.840X1.06 1 Provides sealed cavity inside Adapter.
1C N/A STANDARD INJECTOR
ADAPTER 1 Attaches Injector Asmb. to freezer.
1D 063260 ADAPTOR-INJECTOR O-RING 1 Creates tension to secure Adapter to
Injector Head.
2 063232 INJECTOR-HEAD FB80 1 Connects flavor lines to inject syrups
into product.
2A 063265 O-RING-PORT-SYRUP PARKER
2-011 1 Provides sealed cavity inside syrup port.
2B 063264 O-RING-HEAD-INJECTOR 2-020 1 Provides a sealed cavity.
2C 066088 O-RING-PORT-SYRUP PARKER
larger 1 Provides a sealed cavity.
3 063231 GEAR-CARTRIDGE FB80 1 Rotates product for syrup distribution.
4 063280 TUBEA.-9, 6' LONG FB80 1 Supplies syrup to Injector Head from
pumps.
4A 063213 EYELET-ROLLED FLANGE FB80 18 Provides tension in syrup line to affix
to line coupler.
4B 063253 COUPLING-LINE FB80 2 Holds flavor lines in place.
4C 064186 BAG CONNECTOR O-RINGS 1 Provides extra tension between tube
connectors.
4D N/A 9-TUBE ASMB. WAVE SPRING 1 Provides tension between tube
connectors.
4E N/A LINE COUPLER NUT - BLACK 1 Attaches flavor tubes to manifold.
4F N/A 6' 9-TUBE ASMB. TUBES 9 Brings syrup from pump to Inj Head.
4G 063254 NUT-COUPLING-LINE FB80 1 Connects flavor lines to the internal 9-
Tube Assembly.
4H 063257 GASKET-CONN.-TUBE 9 POS 1 Provides sealed cavity.
5 063229 FITTING-TUBE-BODY-BLK FB80 1 Secures syrup manifold to flavor lines.
6 063245 CAP-DUST-FLAVORLINE FB80 1 Covers unconnected s
y
rup manifold.
7 063230 MANIFOLD-SYRUP-BLACK FB80 1 Connects flavor line to Injector Head.
8 063256 VALVE-CHECK-DUCKBILL
9 POS 1 Seals the cavity to prevent leakage.
9 063246 BRACKET-MTG.-INJECTOR /
CW 1 Supports the Injector Assembly.
9A 063217 KNOB-BRKT.-MTG.-INJECTOR
FB80 1 Tightens positioning of Mounting
Bracket.
9B 063249 WASHER-SHOULDER-NYLON 1
A
llows vertical movement of bracket.

11
Injector Assembly and Related Parts (Continued)
ITEM PART NO. DESCRIPTION QTY. FUNCTION
9C 063247 BRACKET-INJECTOR PART A 1 Attaches Bracket to freezer door bolts.
9D 063255 WASHER-SPRING-BRACKET-
ROTOR 1 Spaces the hanging and base Brackets.
9E 063248 BRACKET-INJECTOR PART B 1 Secures Bracket to Injector Assembly.
10 N/A INJECTOR ASMB. - NO HEAD 1 Powers Injector system.
10A 063347-05 INJECTOR MOTOR ASSEMBLY 1 Supplies power to Motor.
10B 063234 GEAR A.-FB80 1 Gears turn Gear Cartridge for even
syrup distribution.
10C 063212 KNOB-BRKT.-MTG.-
A
CCESSORY 1 Secures Mounting Bracket to Gear Box.
11 063250 BRACKET-HANGING-
ACCESSORY 1 Stores flavor line and Injector Drive Motor when not in use.
12 063348 2' SURFACE RACEWAY 1
A
ttaches flavor lines to side of freezer.
13 063178 ADAPTOR-CROWN W/O-RING 1 Attaches Inj. Asmb. to freezer doors of
most Taylor Crown Series models.
13A 063263 ADAPTOR-O-RING TAYLOR
8750 1 Creates tension to secure Adapter to freezer door.
13B N/A ALTERNATE INJECTOR
A
DAPTER 1 Attaches Injector Asmb. to freezer door.
13C 063260 ADAPTOR-INJECTOR O-RING 1 Creates tension to secure Adapter to
Injector Head.
4H
2
9
4
3
12
11
9B
4B
4G
4E
4D
4B 4F
2C
2B
10A
10C 9A
9C
9E
4A
4A 4C
9D
10B
5678
10
13
13A
13B
13C
1
1A
1B
1C
1D
26003
2A
Figure 4

12
Syrup Pump and Related Parts (See Figure 5)
ITEM PART NO. DESCRIPTION QTY. FUNCTION
1 N/A SOFT SERVE SYRUP PUMP 8 Pumps syrup from flavor bags to
flavor lines.
1A 063274 PUMP-PERISTALTIC-SYRUP
FB80 8 Pumps syrup from flavor bags to flavor lines.
1B 064866 1/8" SYRUP PUMP REPL. TUBE 1 ea. Transports syrup through pump.
1C 063215 WASHER-1/4-PLASTIC
#16FW250062 1 ea. Secures pump tube.
1D 063214 CLAMP-HOSE-1/4" #22HC025
FB80 1 ea. Prevents pump tube from slipping.
1E 063213 EYELET-ROLLED FLANGE FB80 1 ea. Creates tension for tighter fit.
1F 063219 UNION-ELBOW-1/4X1/4OD
FB80 1 ea. Connects syrup in tube to pump.
1G 063218 UNION-1/4X3/16OD FLVR BRST 1 ea. Connects syrup pump to flavor line
out.
2 N/A SYRUP-OUT TUBE ASMB.
FB80M 8 Transports flavor from bag to pump.
2A N/A 1/4” ID HOSE BARB SHUTOFF 1 ea. Connects flavor line to flavor bag.
2B 063276 INJECTOR-FLAVOR-21.5X3/16ID 1 ea. Carries syrup from syrup bag to pump.
2C 063284 TUBE-SILICONE .188X.375 PE
FB80 1 ea. Connects barb fitment to tube port.
2D 063224 FITTING-1/4X1/4 BARB FB80 1 ea. Connects syrup tube to silicone tube.
3 N/A 6' 9-TUBE ASSEMBLY TUBES 9 Brings syrup from pump to Inj. Head.
4 063254 NUT-COUPLING-LINE FB80 1 Connects flavor lines to the internal 9-
Tube Assembly.
5 065179 TUBE CONNECTOR BODY 1 Connects internal 9-Tube Assembly to
flavor lines.
6 063253 COUPLING-LINE FB80 1 Holds flavor lines in place.
7 063213 EYELET-ROLLED FLANGE FB80 9 Creates tension for tighter fit.
8 064184 FLAVOR LINE DUST CAP 1 Cover to protect end of flavor lines.
9 N/A CONNECTOR A.-BAG-
MCD FB80 8 Connects bag fitment to flavor lines.
9A 063282 CAP-VALVE-SYRUP FB80 1 ea. Attaches to flavor bag fitment.
9B N/A SYRUP BAG ADAPTER VALVE
ASSEMBLY 1 ea. Transports syrup to quick connect fitment.
9C 063260 ADAPTOR-INJECTOR O-RING 1 ea. Provides sealed cavity for Connector.
10 063179 TRAY-FLAVORING FLAVOR
BURST 8 Houses syrup bags.
11 063209 CABLE-CABINET-SYRUP
(INTERNAL) 1 Supplies power to the pumps.

13
Syrup Pump and Related Parts
26004
11
3
10
9A 9B
9
4568
7
9C
2
2A 2C 2D
2B
1
1D
1C
1A
1G
1B
1E
1F
Figure 5

14
Sanitizer Pump and Related Parts (See Figure 6)
ITEM PART NO. DESCRIPTION QTY. FUNCTION
1 063266 PUMP-PERISTALTIC-
SANITIZER 1 Supplies sanitizer to flush tube.
2 064867 SANITIZER TUBE
REPLACEMENT 1 Transports sanitizer through pump.
3 064184 FLAVOR LINE DUST CAP 1 Cover to protect end of flavor lines.
4 063213 EYELET-ROLLED FLANGE FB80 9 Provides tension in syrup line to affix
to line coupler.
5 063253 COUPLING-LINE FB80 1 Holds flavor lines in place.
6 065179 TUBE CONNECTOR BODY 1 Connects internal 9-Tube Assembly to
flavor lines.
7 063254 NUT-COUPLING-LINE FB80 1 Connects flavor lines to the internal 9-
Tube Assembly.
8 063209 CABLE-CABINET-SYRUP
(INTERNAL) 1 Supplies power to pumps.
9 063219 UNION-ELBOW-1/4X1/4OD FB80 1 Connects sanitizer line to barb fitment.
10 063236 FB80M SANITIZER FLUSH LINE
ASMB. 1 Connects sanitizer tank to flush lines.
10A N/A FLAVOR LINE FLUSH FITMENT 1 Connects to flavor in tube.
10B 063227 ELBOW-1/4 ID HOSE FB80 2 Connects flush tube to Sanitizer Tank.
10C 063279 TUBE-CLEAR-PER FOOT FB80 5 Transports sanitizer to sanitizer / flush
10D 063222 FITTING-Y-44 FLAVOR BURST 2 Splits sanitizer flush tube into two
11 N/A 6' 9-TUBE ASSEMBLY TUBES 9 Transports sanitizer to Injector Asmb.
12 063218 UNION-1/4X3/16OD FLVR BRST 1 Connects sanitizer line to barb fitment.
13 063221 ADAPTOR-1/4TUBEX1/4HOSE
FB80 3 Connects pump tubes to sanitizer
lines.
14 063272 BOTTLE-SANITIZER-
COMPLETE 1 Houses sanitizer cleaning solution.
14A 063267 VALVE-CHECK-THREADED
FB80 1 Allows air to fill Sanitizer Tank.
14B 063268 NUT-TANK-SANITIZER FB80 1 Mounts check valve to Sanitizer Tank.
14C 063228 FITTING-1/4 ID BARB HOSE
FB80 1 Connects sanitizer lines to Sanitizer
Tank.
14D 063271 CAP-BOTTLE-SANITIZER FB80 1 Allows Sanitizer Tank to be refilled.
14E 063270 O-RING-CAP-SANITIZER
#952992 1 Seals the Sanitizer Tank opening to prevent leakage.
14F 063279 TUBE-CLEAR-PER FOOT FB80 1 Transports sanitizer solution to
sanitizer / flush tubes.
14G 063269 BOTTLE-SANITIZER-MCD 1 Houses sanitizer cleaning solution.
14H N/A SANITIZER TANK O-RING 4 Seals Sanitizer Tank's Quick Connect
and Check Valve openings.
15 063251 TRAY-PARTS FB80 1 Holds sanitized
p
arts while the
y
air

15
Sanitizer Pump and Related Parts
26005
1
2
2
9
13
12
11
8
3
4
5
6
7
15
14
14G
14B
14E
14C
14F
14A
14D
13
13
14H
14H
14H
14H
10
10C
10A 10B
10C 10C
10D
10D
10C
10B
10C
Figure 6

16
Remote Module and Electronic Parts (See Figure 7)
ITEM PART NO. DESCRIPTION QTY. FUNCTION
1 063201 KEYPAD-FB 2001/2002 FB80 1 Flavor Burst unit command center.
2 063196 SWITCH-SPIGOT-STANDARD
FB80 1 Activates Injector Assembly.
3 063347-05 INJECTOR MOTOR ASSEMBLY 1 Supplies power to motor which turns
gears.
4 063242 BRACKET-MTG.-KEYPAD
ELE 500 1 Mounts the Keypad to the freezer
4A 063239 PLATE-MTG.-ROTOR
ASSEMBLY 1 Attaches to freezer to mount Keypad Bracket.
4B 063240 BRACKET-MOUNT-KEYPAD
FB80 1 Holds Keypad in place.
4C 063212 KNOB-BRKT.-MTG.-
ACCESSORY 2 Fastens Keypad Bracket to mounting plate.
5 N/A REMOTE MICROPROCESSOR
MODULE 1 Main power supply.
6 063197 CABLE-POWER #2 FLAVOR
BURST 1 Supplies the electronics board with power.
7 063210 CABLE-PUMP-(EXTERNAL)
MCD 1 Links electronics board to pumps.
8 063209 CABLE-CABINET-SYRUP
(INTERNAL) 1 Supplies power to pumps.
9 068122 8-32 Nuts - Ext. Lock Washer 4 Secures screws to Remote
Microprocessor Module.
10 068121 8-32 X 1/4" Pan Head Screws 4 Fastens Remote Microprocessor
Module to mounting surface.

17
Remote Module and Electronic Parts
4A
4
4B
4C
1
2
3
5
5
6
7
8
26006
(REVERSE SIDE)
9
10
Figure 7

18
Maintenance Kit and Spare Parts Kit (See Figure 8)
ITEM PART NO. DESCRIPTION QTY. FUNCTION
1 063252 KIT-BRUSH-CLEANING FB80 1 Used in Flavor Burst cleaning
procedures.
1A 005162* DETAIL BRUSH –
0.0625"X0.5"X4" 1 Cleans small ports and openings.
1B 033059 SMALL BRUSH - 0.5"X3 X13" 1 Cleans smaller openings and parts.
1C 013073 MEDIUM BRUSH - 1"X3 X16.5" 1 Cleans medium-sized openings and
parts.
1D 014753 LARGE BRUSH –
1.5"X3.5"X19.25" 1 Cleans large openings, parts and flat areas.
2 063273 KIT-SPARE PARTS-INJ 325
SYRUP 1 Houses extra spare parts and wear items.
2A 063231 GEAR-CARTRIDGE FB80 1 Rotates product for even syrup
distribution.
2B 063256 VALVE-CHECK-DUCKBILL
9 POS 1 Provides sealed cavity and prevents syrup leakage.
2C 063260 ADAPTOR-INJECTOR O-RING 1 Creates tension to secure Adapter to
Injector Head.
2D 063261 GASKET-ADAPTOR-.840X1.06 1 Provides sealed cavity inside Adapter.
2E 063262 ADAPTOR-O-RING PARKER #2 1 Creates tension to secure Adapter to
freezer door.
2F 063257 GASKET-CONN.-TUBE 9 POS 1 Provides sealed cavity.
2G 063265 O-RING-PORT-SYRUP PARKER
2-011 1 Provides sealed cavity inside syrup port.
2H 063264 O-RING-HEAD-INJECTOR 2-020 1 Provides a sealed cavity.
2I 063230 MANIFOLD-SYRUP-BLACK FB80 1 Connects flavor line to Injector Head.
2J 063196 SWITCH-SPIGOT-STANDARD
FB80 1 Activates Injector Assembly.
2K 063229 FITTING-TUBE-BODY-BLK FB80 1 Secures flavor line manifold to flavor
lines.
2L 063198 FUSE-1 AMP 1-1/4" SLOW
BLOW 2 System overload protection.
2M 066088 LARGER SYRUP PORT O-RING 1 Provides a sealed cavity.
2N 063263 ADAPTOR-O-RING
TAYLOR 8750 1 Creates tension to secure Adapter to freezer door.
2O N/A DRIVE MOTOR GEAR 1 Turns the gear box gears, powered by the
drive motor.
*If the 005162 Detail Brush is not available for reordering, order the 050103 3-Brush Set. The Detail
Brush is the smallest brush in that set.