FLIR E series User manual

Getting started
FLIR Exx series

Important note
Before operating the device, you must read, understand, and follow all instructions, warnings, cautions, and legal
disclaimers.
Důležitá poznámka
Před použitím zařízení si přečtěte veškeré pokyny, upozornění, varování a vyvázání se ze záruky, ujistěte se, že jim
rozumíte, a řiďte se jimi.
Vigtig meddelelse
Før du betjener enheden, skal du du læse, forstå og følge alle anvisninger, advarsler, sikkerhedsforanstaltninger og
ansvarsfraskrivelser.
Wichtiger Hinweis
Bevor Sie das Gerät in Betrieb nehmen, lesen, verstehen und befolgen Sie unbedingt alle Anweisungen, Warnungen,
Vorsichtshinweise und Haftungsausschlüsse
Σημαντική σημείωση
Πριν από τη λειτουργία της συσκευής, πρέπει να διαβάσετε, να κατανοήσετε και να ακολουθήσετε όλες τις
οδηγίες, προειδοποιήσεις, προφυλάξεις και νομικές αποποιήσεις.
Nota importante
Antes de usar el dispositivo, debe leer, comprender y seguir toda la información sobre instrucciones, advertencias,
precauciones y renuncias de responsabilidad.
Tärkeä huomautus
Ennen laitteen käyttämistä on luettava ja ymmärrettävä kaikki ohjeet, vakavat varoitukset, varoitukset ja lakitiedotteet
sekä noudatettava niitä.
Remarque importante
Avant d'utiliser l'appareil, vous devez lire, comprendre et suivre l'ensemble des instructions, avertissements, mises
en garde et clauses légales de non-responsabilité.
Fontos megjegyzés
Az eszköz használata előtt figyelmesen olvassa el és tartsa be az összes utasítást, figyelmeztetést, óvintézkedést és
jogi nyilatkozatot.
Nota importante
Prima di utilizzare il dispositivo, è importante leggere, capire e seguire tutte le istruzioni, avvertenze, precauzioni ed
esclusioni di responsabilità legali.
重要な注意
デバイスをご使用になる前に、あらゆる指示、警告、注意事項、および免責条項をお読み頂き、その内容を理解し
て従ってください。
중요한 참고 사항
장치를 작동하기 전에 반드시 다음의 사용 설명서와 경고,주의사항,법적 책임제한을 읽고 이해하며 따라야 합니다.
Viktig
Før du bruker enheten, må du lese, forstå og følge instruksjoner, advarsler og informasjon om ansvarsfraskrivelse.
Belangrijke opmerking
Zorg ervoor dat u, voordat u het apparaat gaat gebruiken, alle instructies, waarschuwingen en juridische informatie
hebt doorgelezen en begrepen, en dat u deze opvolgt en in acht neemt.
Ważna uwaga
Przed rozpoczęciem korzystania z urządzenia należy koniecznie zapoznać się z wszystkimi instrukcjami,
ostrzeżeniami, przestrogami i uwagami prawnymi. Należy zawsze postępować zgodnie z zaleceniami tam zawartymi.
Nota importante
Antes de utilizar o dispositivo, deverá proceder à leitura e compreensão de todos os avisos, precauções, instruções
e isenções de responsabilidade legal e assegurar-se do seu cumprimento.
Важное примечание
До того, как пользоваться устройством, вам необходимо прочитать и понять все предупреждения,
предостережения и юридические ограничения ответственности и следовать им.
Viktig information
Innan du använder enheten måste du läsa, förstå och följa alla anvisningar, varningar, försiktighetsåtgärder och
ansvarsfriskrivningar.
Önemli not
Cihazı çalıştırmadan önce tüm talimatları, uyarıları, ikazları ve yasal açıklamaları okumalı, anlamalı ve bunlara
uymalısınız.
重要注意事项
在操作设备之前，您必须阅读、理解并遵循所有说明、警告、注意事项和法律免责声明。
重要注意事項
操作裝置之前，您務必閱讀、了解並遵循所有說明、警告、注意事項與法律免責聲明。

Getting started
FLIR Exx series
#T810160; r. AH/47706/47706; mul

Table of contents
1 List of contents .......................... . .. . . . . . . . . ........................... 1
2 Illustrations . . . . . .......................... ... .. . . . . . . . . . ....................... 3
3 EN-US English ......................................... . .. . . . . . . . . ............. 9
4 CS-CZ Čeština ................................... ... .. . . . . . . . . . ...............14
5 DA-DK Dansk................................................... .. . . . . . . . . . ....19
6 DE-DE Deutsch ..... ... . .. . . . . . ............................... . .. . . . . . . . . .....24
7 EL-GR Ελληνικά .......................... ... .. . . . . . . . . . ......................29
8 ES-ES Español................................... .. . .. . . . . . . . . ................35
9 ET-EE Eesti keel .......................... .. . .. . . . . . . . . .......................40
10 FI-FI Suomi .. . .. . . . . . . . . .......................... ... .. . . . . . . . . . ...............45
11 FR-FR Français ................................................ .. . . . . . . . . . ....50
12 HU-HU Magyar ...................................... ... . . . . . . . . ...............55
13 IT-IT Italiano ......... ... . . . . . . . . ............................... . .. . . . . . ........60
14 JA-JP 日本語. . . . . .......................... ... .. . . . . . . . . .......................65
15 KO-KR 한국어. ... . . . . . . . . ............................ ... . . . . . . . . ...............70
16 NB-NO Norsk. . . . . ............................ ... . . . . . . . . ......................75
17 NL-NL Nederlands. .......................... ... . . . . . . . . ......................80
18 PL-PL Polski............ . .. . . . . . . . . ............................. .. . . . . . . . . . ....85
19 PT-PT Português...................... ... . . . . . . . . .............................90
20 RU-RU Русский................................................ .. . . . . . . . . .....95
21 SV-SE Svenska................ . .. . . . . . ............................. .. . .. . . . . 100
22 TR-TR Türkçe............... ... . . . . . . . . ............................ . .. . . . . . . . 105
23 ZH-CN 简体中文 .................................. .. . .. . . . . . . . . .............. 110
24 ZH-TW 繁體中文 .................................. .. . .. . . . . . . . . .............. 115
#T810160; r. AH/47706/47706; mul vii

1 List of contents
• Accessory Box I:
◦ Power supply for battery charger
◦ Power supply, 15 W/3 A
◦ Printed documentation
◦ SD card (8 GB)
◦ USB 2.0 A to USB Type-C cable, 1.0 m
◦ USB Type-C to HDMI adapter, standard specification UH311
◦ USB Type-C to USB Type-C cable (USB 2.0 standard), 1.0 m
• Accessory box II:
◦ Accessory box III:
– Front protection fastener
– Hand strap bracket, left
– Hand strap bracket, right
– Screws
– Torx T10 wrench
◦ Carabiner hook
◦ Front protection
◦ Hand strap
◦ Lanyard strap, camera
◦ Lens cap strap
◦ Wrist strap
• Battery (2 ea)
• Battery charger
• Hard transport case
• Infrared camera
• IR lens, f = 10 mm (0.39 in.), 42°1
• IR lens, f = 18 mm (0.71 in.), 24°1
• IR lens, f = 29 mm (1.41 in.), 14°1
• Lens cap, front
• Lens cap, front and rear (only for extra lenses)
#T810160; r. AH/47706/47706; mul 1
1. The inclusion of this item is dependent on the camera model.

1 List of contents
Note FLIR Systems reserves the right to discontinue models, parts or acces-
sories, and other items, or to change specifications at any time without prior
notice.
#T810160; r. AH/47706/47706; mul 2

2 Illustrations
Note Explanations of the illustrations in Figure 2.1 - Figure 2.4 are provided in
each language section.
Figure 2.1 View from the front
#T810160; r. AH/47706/47706; mul 3

2 Illustrations
Figure 2.2 View from the rear
#T810160; r. AH/47706/47706; mul 4

2 Illustrations
Figure 2.3 Screen elements
Figure 2.4 Menu system
#T810160; r. AH/47706/47706; mul 5

2 Illustrations
Table 2.1 Mounting the hand strap.
1. 2.
3. 4.
#T810160; r. AH/47706/47706; mul 6

2 Illustrations
Table 2.2 Mounting the lanyard strap (lanyard not included).
1. 3.
2.
#T810160; r. AH/47706/47706; mul 7

2 Illustrations
Table 2.3 Mounting the wrist strap.
1. 2.
3. 4.
#T810160; r. AH/47706/47706; mul 8

3 EN-US English
3.1 Thank you!
Thank you for choosing a product from FLIR Systems. We hope that the product
will meet your expectations and that you will consider us again for your future
needs.
3.2 Read the manual before use
Go to the following website to read or download the
manual:
http://support.flir.com/resources/hu4b
3.3 Extend your product warranty
Our aim is to provide the best quality and workmanship in the industry. To prove
this, we offer the most generous extended warranty on the market.
Register your product now to get:
• 2 years camera warranty
• 10 years detector warranty
Go to the following website to activate your extended warranty:
http://support.flir.com/camreg
For more information about the registration procedure, refer to the user’s manual.
Note Registration must be completed within 60 days of purchase.
3.4 Download FLIR Tools
FLIR Tools lets you quickly create professional inspection reports that clearly
show decision makers what you’ve found with your camera.
#T810160; r. AH/47706/47706; mul 9

3 EN-US English
Import, analyze, and fine-tune images easily. Then incorporate them into concise
documents to share findings and justify repairs.
Go to the following website to download FLIR Tools:
http://support.flir.com/tools
3.5 Check out our FLIR apps
Use our apps to analyze your IR images, create reports, and share your reports
using Dropbox, Box.net, FTP, e-mail, etc.
Use your mobile device to go to the following website and download the apps:
http://onelink.to/tools
3.6 Quick start guide
Follow this procedure:
1. Put a battery into the battery compartment.
2. Connect the USB battery charger to the USB connector at the top of the
camera.
3. Charge the battery for 2 hours before starting the camera for the first time.
4. Insert a memory card into the card slot at the top of the camera.
Note Empty or use a memory card that has not previously been used in an-
other type of camera. The cameras may organize files differently on the
memory card. There is therefore a risk of losing data if the same memory
card is used in different types of cameras.
5. Push the on/off button to turn on the camera.
6. Aim the camera toward the object of interest.
7. Adjust the infrared camera focus by rotating the focus ring.
Note It is very important to adjust the focus correctly. Incorrect focus ad-
justment affects how the image modes work. It also affects the temperature
measurement.
8. Pull the trigger to save an image.
9. Download and install FLIR Tools/Tools+ (freeware) or FLIR Report Studio (li-
censed software) on your computer.
10. Start FLIR Tools/Tools+ or FLIR Report Studio.
11. Connect the camera to the computer using the USB cable.
#T810160; r. AH/47706/47706; mul 10

3 EN-US English
12. Import the images into FLIR Tools/Tools+ or FLIR Report Studio and create
an inspection report.
13. Send the inspection report to your client.
3.7 View from the front
See Figure 2.1 View from the front, page 3.
1. Laser distance meter.2
2. Infrared lens.
3. Focus ring.
4. Autofocus button.2
5. Trigger.
6. Lamp for the digital camera (left and right sides).
7. Digital camera.
8. Attachment point for the hand strap bracket (left and right sides).
9. Tripod mount.
10. Attachment point for the hand strap, wrist strap, or lanyard strap (left and
right sides).
3.8 View from the rear
See Figure 2.2 View from the rear, page 4.
1. Cover for the USB connector and memory card slot.
2. Microphone.
3. Speaker.
4. Touch-screen LCD.
5. Image archive button.
6. Programmable button.
7. Button to operate the laser.
8. Back button.
9. On/off button.
10. Navigation pad with center push.
11. Battery.
3.9 Screen elements
See Figure 2.3 Screen elements, page 5.
1. Result table.
#T810160; r. AH/47706/47706; mul 11
2. This item is dependent on the camera model.

3 EN-US English
2. Status icons.
3. Measurement tool (e.g., spotmeter).
4. Temperature scale.
5. Menu system button.
3.10 Menu system
See Figure 2.4 Menu system, page 5.
1. Temperature scale button.
2. Measurement parameters button.
3. Image mode button.
4. Measurement button.
5. Color button.
6. Settings button.
7. Main menu.3
8. Submenu.
3.11 To keep in mind
• Adjust the focus first. When the camera is out of focus, the measurement will
be wrong.
• By default, most cameras adapt the scale automatically. Use this mode first,
but do not hesitate to set the scale manually.
• A thermal camera has a resolution limit. This depends on the size of the de-
tector, the lens, and the distance to the target. Use the center of the spot tool
as a guide to the minimum possible object size, and get closer if necessary.
Make sure to stay away from dangerous areas and live electrical components.
• Be careful when holding the camera perpendicular to the target. Be observant
of reflections, especially at low emissivities—you, the camera, or the sur-
roundings may become the main source of reflection.
• Select a zone of high emissivity, e.g., an area with a matte surface, to perform
a measurement.
• Blank objects, i.e., those with low emissivities, may appear warm or cold in
the camera, because they mainly reflect the environment.
• Avoid direct sunlight on the details that you are inspecting.
• Various types of faults, e.g., those in a building’s construction, may result in
the same type of thermal pattern.
#T810160; r. AH/47706/47706; mul 12
3. This item is dependent on the camera model.