Floe V-2000 User manual

SHEET 1 OF 8
FLOE LEG EXTENSIONS
SMALL LIFTS (V2000-VSD5000 PONTOON)
LARGE LIFTS (VSD6000-VSD8000)
ASSEMBLY INSTRUCTIONS
KIT P/N 511-06005-00, 511-06006-00
INSTRUCTION P/N: 611
-
0
6005
-
00
RELEASED 7/11/19
© Manufactured by:
Floe International Inc.
48473 State Hwy. 65
McGregor, MN 55760
www.floeintl.com
IMPORTANT NOTE
FOR INSTALLATION OF LEG EXTENSIONS, THE LIFT MUST BE RAISED ON ONE
END (BOTH IF INSTALLING TWO KITS). BE SURE TO PROPERLY SUPPORT THE LIFT
TO AVOID TIPOVER, WHICH MAY LEAD TO SERIOUS INJURY, DEATH, OR
DAMAGE TO LIFT AND OR LIFT COMPONENTS.
TOOLS REQUIRED
-(2) 3/4” WRENCHES/SOCKETS
-TAPE MEASURE
-TORQUE WRENCH
-HIGH LIFT JACK (OR
EQUIVALENT)
*
V2000
-
VSD5000 PONTOON (VSD5000 SHOWN)
*
VSD6000
-
8000 (VSD6500/8000 SHOWN)
*LIFT NOT INCLUDED

SHEET 2 OF 8
BILL OF MATERIALS/EXPLODED VIEW
P/N 511-06005-00 EXTENSION LEGS, V2000-VSD5000
NUMBER PART NUMBER QTY. DESCRIPTION
1 001-70218-00 2 HHCS, ½-13 x 3 ¾” 18-8 ss
2 001-76072-00 2 NUT, NYLOCK ½-13 ALUM.
3 111-00219-00 2 WELD’T, EXTENSION LEG – 27”
P/N 511-06006-00 EXTENSION LEGS, VSD6000-8000
NUMBER PART NUMBER QTY. DESCRIPTION
1 001-70224-00 2 HHCS, ½-13 x 5 ½” 18-8 ss
2 001-76072-00 2 NUT, NYLOCK ½-13 ALUM.
3 111-00220-00 2 WELD’T, EXTENSION LEG – 20.5”

SHEET 3 OF 8
PLACEMENT
LEG EXTENSIONS CAN BE PLACED ON ANY END OR CORNER OF THE BOAT LIFT (ON CORNER POSTS
“A” & “D” OR “B” & “C”). WHEN CHOOSING A LOCATION, ENSURE THAT THE LIFT WILL BE STABLE UPON
INSTALLATION.
EXTENSIONS ON CORNER
POSTS “A” & “D”
EXTENSIONS ON CORNER
POSTS “B” & “C”
EXTENSIONS ON CORNER
POSTS “C” & “D”
EXTENSIONS ON CORNER
POSTS “A” & “B”
EXTENSIONS ON
CORNER POSTS
“B” & “D”
(CAN BE PLACED ON “A” & “C”
ALSO)

SHEET 4 OF 8
INSTALLATION
RAISE END OF LIFT WITH A HIGH LIFT JACK (OR EQUIVALENT) THAT WILL HAVE THE LEG EXTENSIONS
INSTALLED ON. FOR SMALL LIFTS, RAISE FRAME BEAM 44” ABOVE THE GROUND (FIGURE 1.1). FOR
LARGE LIFTS, RAISE FRAME BEAM 38” ABOVE THE GROUND (FIGURE 1.1A). REMOVE ½” NYLOCK NUT
AND ½” BOLT ON EACH SANDPAD, THEN REMOVE SAND PADS (FIGURE 1.2).
IMPORTANT NOTE
FOR INSTALLATION OF LEG
EXTENSIONS, THE LIFT MUST BE RAISED
ON ONE END (BOTH IF INSTALLING
TWO KITS). BE SURE TO PROPERLY
SUPPORT THE LIFT TO AVOID
TIPOVER,
FIGURE 1.1
2X
FIGURE 1.2
FIGURE 1.1A

SHEET 5 OF 8
LOWER INNER LEGS USING ADJUSTING SCREW (FIGURE 1.3). FOR SMALL LIFTS, LOWER THE INNER LEG
10” FROM THE BOTTOM OF THE INNER LEG TO THE BOTTOM OF THE CORNER POST (FIGURE 1.4). FOR
LARGE LIFTS, LOWER THE INNER LEG 10-1/8” FROM THE BOTTOM OF THE INNER LEG TO THE BOTTOM
OF THE CORNER POST (FIGURE 1.4A).
FIGURE 1.4
FIGURE 1.3
2X
FIGURE 1.4A
2X

SHEET 6 OF 8
SLIDE LEG EXTENSIONS ONTO INNER LEGS AND ALIGN HOLES (FIGURE 1.5: SMALL LIFTS, FIGURE 1.5A:
LARGE LIFTS). FOR SMALL LIFTS, ATTACH LEG EXTENSION TO INNER LEG USING (1) ½” X 3-3/4” BOLT
AND (1) ½” NUT (FIGURE 1.6).
FIGURE 1.5
2X
FIGURE 1.6
2X
2X
FIGURE 1.6

SHEET 7 OF 8
FOR LARGE LIFTS, ATTACH LEG EXTENSION TO INNER LEG USING (1) ½” X 5 ½” BOLT AND (1) ½” NUT
(FIGURE 1.6A). TORQUE TO 25 FT-LBS (FIGURE 1.7). RE-ATTACH SAND PADS TO LEG EXTENSIONS
USING THE ½” BOLTS AND ½” NYLOCK NUTS THAT WERE USED TO ATTACH THEM TO THE LIFT’S INNER
LEG (FIGURE 1.8). TORQUE TO 25 FT-LBS (FIGURE 1.9).
FIGURE 1.6A
2X
2X
2X 2X
FIGURE 1.7
FIGURE 1.8 FIGURE 1.9

SHEET 8 OF 8