Foamit SP10.0L User manual

2.6 Gallon Pump-Up Spray Unit
READ ALL INSTRUCTIONS BEFORE USING OR
SERVICING THIS UNIT. KEEP THIS MANUAL IN A
LOCATION THAT IS READILY AVAILABLE TO USERS
AND SERVICE TECHNICIANS.
English (Original Instructions) Scan this code
for user manual
SP10.0L | SP10.0L-PSG
User Manual
SP10.0L
SP10.0L-PSG

V20231106 •Page 2 of 7Model: SP10.0L | SP10.0L-PSG
WARNING
!
Safety
PEOPLE OR OBJECTS CAN BE HURT OR DAMAGED IF THIS UNIT IS NOT USED CORRECTLY!
Failure to read all the instructions before operating the unit may result in personal injury or death from
the improper use or the chemical solution. Anyone handling, operating or using the unit must read and
understand the instructions in the manual. The buyer assumes all responsibility for safety and proper use
in accordance with the instructions.
Using or servicing the unit without appropriate personal protective equipment (PPE)
may result in serious injury such as burns, rashes, eye, throat or lung damage and
death. Always wear PPE as indicated in the Safety Data Sheet (SDS) when using or
servicing the unit. Protect eyes, skin, and lungs against drifting spray.
Chemical solutions may pose a health risk and death if they contact the skin or eyes, are inhaled
or swallowed. Always read and follow all chemical safety precautions and handling instructions provided
by the chemical manufacturer and the SDS associated with the chemical solution before using the unit.
Pressure within the equipment may cause an unexpected release of the chemical solution and
cause serious injury such as burns, rashes, eye damage, throat or lung damage and death.
Always depressurize and clean the unit after each use. Never leave the unit unattended while
pressurized.
Using the unit with fluid temperatures above 100°F (37.8°C) may result in scalding, burns, serious injury or
death. DO NOT use a solution with a temperature above 100°F (37.8°C).
Operating the unit when damaged or leaking may result in exposure to chemical solutions, serious injury
or death. Never use the unit if it is damaged or leaking.
Never point the discharge wand at yourself, another person, or any object you do not want covered
in chemical.
Use of hydrocarbons and flammable products may result in explosions, fire and serious injury or death.
Never use hydrocarbons or flammable products with the unit.
Mixing an alkaline with an acid may result in a chemical reaction. Overheating of the mixture may cause
it to splatter caustic compounds or release hazardous fumes, gas and vapors. Always flush the unit with
fresh water thoroughly when switching from an alkaline to an acid or an acid to an alkaline.
Servicing, or modification, of this unit with parts not listed in this manual may cause the unit to operate improperly.
Do not use unauthorized parts when servicing the unit.
Only lift and carry unit by the carrying handle. Do not lift or carry the unit by the pump handle, hose, wand, or other
components.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials, old machine components, and hazardous fluids in an
environmentally safe way according to local waste disposal regulations.
NOTICE

V20231106 •Page 3 of 7Model: SP10.0L | SP10.0L-PSG
Product Overview
Requirements
Liquid temperature range 40-100˚F (4.4-37.8˚C)
Chemical compatibility
Chemical products used with this equipment must be formulated for this
type of application and compatible with unit materials and pump seals.
For more information on chemical compatibility, consult the manufacturer
or SDS for your product or contact our customer service department.
SP10.0L SP10.0L-PSG
Power type Manual
Chemical pickup type Draws from pre-mixed solution
Number of products unit can draw from One product
Suction line length/diameter 18 in. (45.7 cm) clear poly tubing with ⁄ in. (3.2 mm) inside diameter
Capacity 2.6 gallons (10 liters)
Discharge line length/diameter 6.5 ft. (2 m) hose, with ⁄ in. (6.4 mm) inside diameter
Discharge wand/tip type
Polypropylene trigger handle with
17 in. (43.2 cm) wand extension
and 80˚ fan tip
Polypropylene trigger handle
with 40˚ fan tip
Output distance* 3-5 ft. (0.9-1.5 m)
Output volume* 0.2 gal/min (0.8 l/min) 0.3 gal/min (1.1 l/min)
Flow rate* 0.2 gal/min (0.8 l/min) 0.3 gal/min (1.1 l/min)
Pump seals Viton
Specifications
*Rates given are based on chemical with viscosity of water and factory air pressure settings. These rates can vary
based on viscosity of product and fan tip size.

V20231106 •Page 4 of 7Model: SP10.0L | SP10.0L-PSG
Product Components
Get to know the components that you will need to use, adjust or assemble.
Pump-Up Spray Unit • 2.6 Gallon
1. Discharge wand
2. Trigger gun
3. Pressure relief valve
4. Discharge hose
5. Pump handle
6. Tank head
7. Solution tank
SP10.0L-PSG SP10.0L
3
7
4
6
5
2
11

V20231106 •Page 5 of 7Model: SP10.0L | SP10.0L-PSG
2
Using your unit
Operating Instructions
1. Remove components from packaging.
2. For SP10.0L: Attach wand assembly to the trigger
handle. For SP10.0L-PSG: Continue to step 3.
3. Pull the green pressure release valve until the red
portion of the stem is showing to confirm the unit is
not pressurized.
4. With the pump handle pressed fully down, hold the
unit and unscrew the pump assembly from the tank
head to access the filler hole.
5. Follow all instructions from the chemical
manufacturer when filling the unit. Fill the tank ¾ full
with pre-mixed solution. Do not overfill the tank.
6. With the pump handle pressed fully down, hold the
unit and screw the pump assembly back into the
tank head to close the unit.
7. To pressurize the tank, rotate the handle of the
pump assembly until it is free then pump up the unit.
The pressure relief valve will begin leaking air when
the tank is fully pressurized.
8. Once the desired pressure has been achieved,
push the pump handle down and rotate to lock
it in place.
9. To begin spraying, point the discharge wand towards
the area you wish to spray and squeeze the trigger
handle. Release the handle to stop.
After Use Instructions
10. Release air pressure from unit after each use by
activating the pressure relief valve.
11. Empty out remaining solution and run fresh water
through the unit to rinse all parts thoroughly after
each use and before storage.
Maintenance Instructions
To keep your unit operating properly, periodically
perform the following maintenance procedures:
• Check the pump assembly for wear and leaks.
• Check the suction line for debris and clean as
needed.
• Periodically lubricate the pump seal with food safe
lubricant. To lubricate the pump seal, raise the handle
of the pump assembly and apply 5-10 drops of food
safe lubricant between the pump and pump sleeve.
SP10.0L
SP10.0L-PSG
9
6
4
5
2
3

V20231106 •Page 6 of 7Model: SP10.0L | SP10.0L-PSG
Item number Description
5LC-LLA Long lance (10 in.) assembly for
5L / 10L - with retaining nuts
6LC-PRV Pressure relief valve for 5L / 10L
7LC-PSG Poly spray gun for 5L / 10L - blue
8LC-HA Hose assembly for 5L / 10L
9LC-PA Manual pump assembly for
5L / 10L - Viton
10 LC-THA-SP10.0L
Tank head assembly for 10L
spray unit - with pressure relief
valve and tank handle
11 TANK10L 10 liter tank
12 LC-HNDL-CLP Tank handle for 5L / 10L - with
clips
Servicing your unit
SP10.0L
Item number Description
1LC-SLA Short lance (2 in.) assembly - no
retaining nut, o-ring, spray tip
2LC-WA-OR O-ring for 5L / 10L wand assembly
3STB8002 Spray tip - button style - 80 degree
- 0.2 GPM
4LC-WA-RN Retaining nut for 5L / 10L wand
assembly
43
21
9
10
8
7
11
12
6
5
LC-SLA-SP
a
SP10.0L:
10 liter pump-up spray unit
LC-SLA-SP:
Short lance assembly - for 10L spray unit - includes spray
tip, gasket, and retaining nut

V20231106 •Page 7 of 7Model: SP10.0L | SP10.0L-PSG
4
Item number Description
7LC-PRV Pressure relief valve for 5L / 10L
8LC-PA Manual pump assembly for
5L / 10L - Viton
9LC-THA-SP10.0L
Tank head assembly for 10L
spray unit - with pressure relief
valve and tank handle
10 TANK10L 10 liter tank
11 LC-HNDL-CLP Tank handle for 5L / 10L - with
clips
Servicing your unit
SP10.0L-PSG
Item number Description
1ST4003SS Spray tip - 80 degree - 2.0 GPM -
stainless - ⁄ MPT
2PW12M14F4 1/2 in. NPT and ⁄ in. FNPT wand -
black UHMW - 4 in. long
3PSGORV O-ring for poly spray gun
4PSG12
Poly spray gun with 2x ⁄ in. straight
thread - gray handle with red clip -
316SS internal spring - includes 2x
o-ring
5HBSS1214 Stainless hose barb ½ MPT x ⁄ barb
6SSC14 Stainless screw band clamp for ⁄ in.
hose
4
2
3
1
6
5
8
9
10
11
7
PSGA144-ST4003
SP10.0L-PSG:
10 liter pump-up spray unit with PSG trigger gun
PSGA144-ST4003:
Poly spray gun assembly for ⁄ in. hose - includes 4 in.
black poly wand, spray tip, hose barb, and screw band
clamp