Foamit X-FOGCS-10G User manual

USER
MANUAL
MODEL NUMBER:
X-FOGCS-10G
10G (38L) Portable Air-Operated
Fogging Unit
English (Original Instrucons)

Page 2 of 7
User Manual: Portable Air-Operated Fogging Unit | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model Number: X-FOGCS-10G
WARNING
PROTECT THE ENVIRONMENT
Please dispose of packaging materials, old machine
components, and hazardous uids in an environmentally safe
way according to local waste disposal regulaons.
Always remember to recycle.
*Specicaons and parts are subject to change without noce.
Read this manual completely and understand the
machine before operang or servicing it.
• Read all instrucons before installing or operang unit.
• Always wear appropriate personal protecve equipment
(PPE) when operang or servicing unit.
• Always follow all chemical safety precauons and
handling instrucons provided by the chemical
manufacturer and Safety Data Sheet (SDS).
• If this unit is modied or serviced with parts not listed in
this manual, the unit may not operate correctly.
• Always depessurize unit aer use (as described in the
Aer Use Instrucons).
• Do not exceed an incoming air pressure of 100 psi (7
bar).
• Do not exceed a uid temperature of 100˚F (37˚C).
• Always ush the unit with fresh water for 5 minutes
when switching from an alkaline to an acid or an acid to
an alkaline.
• Never use unit with hydrocarbons or ammable
products.
• Only use clean and dry air. Air must be ltered and free
of moisture or pump life will be diminished. If needed,
install an air dryer before unit.
• Do not use an air lubricator before the unit.
• Never use unit if it is damaged or leaking.

Page 3 of 7
User Manual: Portable Air-Operated Fogging Unit | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model Number: X-FOGCS-10G
OPTIONS
Pump Seal Material
X-FOGCS-10G Viton (V)
REQUIREMENTS
Compressed air requirements 50 psi (3.4 bar) with 7 cfm (198.3 l/min)
Liquid temperature range 40-100˚F (4.4-37˚C)
Chemical compability Chemical products used with this equipment must be formulated for this type of applicaon
and compable with unit materials and pump seals. For more informaon on chemical
compability, consult the manufacturer or SDS for your product or contact our customer
service department.
SPECIFICATIONS
Power type Compressed air
Chemical pickup type Draws from pre-mixed soluon
Number of products unit can
draw from
One product
Sucon line length/diameter 3/8 in. (9.5 mm) inside diameter
Capacity 12.5 gallons (47.32 liters)
Flow rate* 3.7 gal/hour at each nozzle
Pump seals Santoprene, Viton, or Kalrez
Droplet size 15 microns at 50 psi
Coverage area** 1 liter of soluon will cover approximately 1000 cubic feet (up to system max of 47,320 cubic
feet).
Run me from full tank** Approx. 1.5 hours
Number of nozzles 2 nozzles
Wheel type Two 10 inch non-marking wheels
*Diluon rates and ow rates given are based on chemical with viscosity of water and factory air pressure sengs.
**Area covered and run me may vary based on humidity, air ow, and product used.

Page 4 of 7
User Manual: Portable Air-Operated Fogging Unit | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model Number: X-FOGCS-10G
Operaon Instrucons
Always follow all chemical safety precauons and handling
instrucons provided by the chemical manufacturer and Safety
Data Sheet (SDS).
1. Follow all instrucons from chemical manufacturer.
Fill the tank with water and the advised percentage of
chemical concentrate.
2. Place the unit in the area to be fogged.
3. Ensure the air supply valve (BVB14) is in the closed
posion, and connect a compressed air line to the air inlet
ng (AP25).
4. Open the air supply valve (BVB14) to acvate the unit.
5. Evacuate the area.
6. Aer the unit has stopped fogging, observe all appropriate
safety precauons before reentering area. Close the air
supply valve (BVB14) and disconnect the compressed air
line from the unit.
Aer Use Instrucons:
1. Flush the unit with fresh water for 5 minutes.
2. Disconnect the air line from the air ng (AP25).
Maintenance Instrucons:
To keep your portable unit operang properly, periodically
perform the following maintenance procedures:
• Check the air pump (P56/P56K/P56V) for wear and leaks.
• Inspect hoses for leaks or excessive wear. Make sure all
hose clamps are in good condion and properly secured.
• Check the sucon tube and screen for debris and clean as
needed.
• Drain compressor tank on a regular basis to ensure proper
operaon of pump.
Troubleshoong Instrucons:
• If air passes through the pump (P56/P56K/P56V) without
cycling, the pump needs to be replaced.
• Check the chemical sucon line and strainer for debris or
damage. Clean or replace as needed. To prevent damage
to the unit, the strainer (STR38-IL) must always be used.
• Check for proper air pressure on air gauge (AG100). Air
regulator (R14) is factory set at 50 psi (3.4 bar).
• If the unit foams at a reduced pressure:
o Check the air compressor supplying the unit. If the
pressure is less than 40 psi, turn the foam unit o
unl the compressor can catch up.
o If the air supply is 50 psi (3.4 bar) or above, check the
AG100, which should read near 50 psi (3.4 bar). If
the AG100 is more or less than 50 psi (3.4 bar), adjust
the pressure by turning the knob on the top of the air
regulator (R14).

Page 5 of 7
User Manual: Portable Air-Operated Fogging Unit | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model Number: X-FOGCS-10G
SSP12
SSAXLE14
AS1-VS
W15
FWAX15
PVCV34FM
COT
TANK-10N
DFP7
DP-A
TANK ASSEMBLY
AIR HOSE ASSEMBLY
ITEM NUMBER: AH30
WATER SEPARATOR
ITEM NUMBER: WS-20CFM
OPTIONAL COMPONENTS

Page 6 of 7
User Manual: Portable Air-Operated Fogging Unit | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model Number: X-FOGCS-10G
Plate - Inside View
Plate - Back View
QFSEL38
QFSEL38
SSA14
BEL14M14M
BVB14
AP25
AG100
R14
QFBH38
HBSSEL1814
QFEL1438
HBSSEL1438
QFSEL38
STR38-IL
HHPB3414
P56, P56K or P56V
PVCV34FM
FOG NOZZLE ASSEMBLY
H38CP
EL14M14F
PFN-N130
QFT38
FG-10N-2-BRKT
QF1438
QFSEL38
(Available per .)

Page 7 of 7
User Manual: Portable Air-Operated Fogging Unit | English
READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT
Model Number: X-FOGCS-10G
ITEM NUMBER DESCRIPTION
AG100 1.5 INCH DRY MODEL 20 DUAL SCALE GAUGE
AH30 30 FT. AIR HOSE WITH QUICK CONNECT FITTINGS
AP25 PLUG 1/4 NPTM AIR FITTING - BRASS
AS1-VS 1/4-20 X 1/2 PHIL TRUSS MACH SCREW 19-8 W/516
ORANGE VIBRASEAL PATCH
B103234 10-32 X 3/4 PHIL TRUSS MACH SCR 18-8
B8X58 8-15 X 5/8 inch PHIL FLAT TY-A 316 S.S.
BEL14M14M BRASS ELBOW 1/4in MPT X 1/4in MPT
BPS-58SO Back Panel Screw - 5/8 inch with Stand O
BPS-SSR 1/4 INCH PUSHNUT BOLT RETAINER STAINLESS STEEL
BVB14 AIR INLET VALVE - VA BRS 025-4F4F-BT, NICKEL
COT 1/8 X 1 COTTER PIN 18-8 S/S
DFP7 7 INCH HINGED CAP ASSEMBLY - INCLUDES BLACK
CAP, LID FLANGE AND HINGE PIN
DFP7-C 7 INCH FILL CAP POLYPRO BLACK
DFP7-F 7 INCH TANK LID FLANGE POLYPRO
DFP7-PIN HINGE PIN FOR DFP7-C & DFP7-C
DFP7-C-BL 7 INCH FILL CAP POLYPRO BLUE PANTONE
DFP7-C-GN 7 INCH FILL CAP POLYPRO GREEN PANTONE
DFP7-C-RD 7 INCH FILL CAP POLYPRO RED PANTONE
DFP7-C-YL 7 INCH FILL CAP POLYPRO YELLOW PANTONE
DP-A DRAIN PLUG ASSEMBLY FOR TANK-10N TANK-20N
DP FRONT DRAIN PLUG FOR PORTABLE UNIT POLYPRO
DP-G FKM SQUARE CUT DRAIN PLUG GASKET
EC14-2 OETIKER CLAMP 13.8
EL14M14F 1/4 FEM PIPE X 1/4 M PIPE ELBOW
FG-10N-2-BRKT BRACKET FOR FG-10N-2
FMS1034 10 X 3/4in PHIL SHEET METAL SS SCREW
FWAX15 FLAT AXLE WASHER
FWLG14 .569 ID X 1.28 OD X .08 THICK FLAT WASHER SS 18-8
H38B-F 3/8 INCH BLUE HOSE-HYBRID TPE-Available per .
H38CP 3/8IN OD POLYETHYLENE TUBING - NATURAL
HBBEL1414 HOSE BARB 1/4 MPT X 1/4 BARB ELBOW
HBSSEL1438 STAINLESS HOSE BARB ELBOW 1/4 INCH NPT X 3/8
HOSE BARB
HHBB1418 HEX HEAD BUSHING 1/4 MPT X 1/8 FPT
HHPB3414 HEX HEAD POLY REDUCER BUSHING 3/4 X 1/4
P56 5700 PUMP WITH SANTOPRENE SEALS - INCLUDES
HOSE BARBS, AIR FITTING, AND AIR PORT
P56K 5700 PUMP WITH KALREZ SEALS - INCLUDES HOSE
BARBS, AIR FITTING, AND AIR PORT
P56V 5700 PUMP WITH VITON SEALS - INCLUDES HOSE
BARBS, AIR FITTING, AND AIR PORT
20756103B Polypro G57 Air Port x HB Straight, w/ Viton o-ring
HB14P 1/4in BRASS HB AIR FITTING /G57/P56
HB5638 HOSE BARB FOR P56 PUMP
HB5638K HOSE BARB FOR P56K PUMP
HB5638V HOSE BARB FOR P56V PUMP
PFN-N130 PNEUMATIC FOG NOZZLE - POLYPROPYLENE AND
KYNAR TIP - 3.7 GAL/HR PER NOZZLE
PLPF-B BLANK PORTABLE FOAMER PLATE WITH HINGE W/O
HOLES
PLPF-PIN 302 STAINLESS PORTABLE PLATE HINGE PIN
PVCV34FM PVC VALVE 3/4in FPT X 3/4in MPT
QF1438 MALE CON. 3/8in TUBE X 1/4in MPT - POLYPROPYLENE
QF5638 3/8in QF PUMP FITTING / G57
QFBH38 BULKHEAD 3/8in TUBE POLYPROPYLENE
QFEL1438 FIXED ELBOW 3/8in TUBE X 1/4in MPT -
POLYPROPYLENE
QFSEL38 PLUG-IN ELBOW 3/8in TUBE X 3/8in POLYPROPYLENE
QFT38 UNION TEE 3/8in TUBE POLYPROPYLENE
R14 1/4 NPTF REGULATOR W/ FILTER-NO GAUGE
SSA14 SS304 MALE/FEMALE ADAPTOR 1/4 NPT X 1/4 NPT
SSAXLE14 14 ½” long with the 5/8” diameter bar & 2 through
holes with countersinks beveled ends
SSC38 WORM GEAR CLAMP, S/S (.25-.63)
SSP12 STAINLESS STEEL AXLE PLATE - 2.5 inch X 1 inch - 2
HOLE
STR38-IL IN LINE STRAINER 3/8 BARB 20 MESH 304 STAINLESS
EDPM GSKT
TANK-10N 10 GALLON NATURAL TANK
TW916 1/2 INT TOOTH L/W 410SS
W15 NONMARKING WHEEL FOR PORTABLE UNITS
WS-20CFM TSUNAMI WATER SEPARATOR 20 CFM