Follett Horizon Elite HCD1810RBS User manual

Order parts online
www.follettice.com
Horizon Elite™Ice Machine Models with RIDE™Technology
Installation Instructions for Ice Storage Bins
HCD/HMD/HCF/HMF1810RBS, HCD/HMD/HCF/HMF2110RBS
HCD/HMD1810NBS, HCD/HMD2110NBS
(See model number congurator on page 2 for details.)
remote condensing
01157874R01
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com

2self-contained BIN • RIDE Technology
CAUTION!
• This appliance should be connected by a qualied person in accordance with applicable codes.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
• Connect to potable water supply only.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory,
or mental capabilities, or lack of experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved. Children should be
supervised to ensure that they do not play with the appliance.
• This appliance is intended to be used for household and similar applications such as staff kitchen areas
in shops, offices and other working environments; farm houses and by clients in hotels, motels and
other residential type environments; bed and breakfast type environments; catering and similar non-retail
applications.
• WARNING! To avoid a hazard due to instability of the appliance, it must be xed in accordance with the
instructions.
ConfigurationApplication
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
425 up to
425 lbs
(193 kg)
710 up to
675 lbs
(306 kg)
1010 up to
1061 lbs
(482 kg)
1410 up to
1466 lbs
(665 kg)
1810 up to
1790 lbs
(812 kg)
2110 up to
2039 lbs
(925 kg)
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager
diverter valve
system
P Cornelius Profile
PR150
CondenserSeriesVoltageIcemaker
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
MC Maestro™
Chewblet®
(425 Series)
HC Horizon
Chewblet
(710, 1010,
1410, 1810,
2110 Series)
HM Horizon
Micro Chewblet
HC 1810D SVA
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
Chewblet®Ice Machine Model Number Configurations

3
BIN • RIDE Technology self-contained
Front cover
8
Internal connection
7
Ice transport tube
5
External connection
6
Docking assembly
4
Bin preparation
3
Site preparation
2
Unpack
1
Read and complete the following 8 installation steps

4self-contained BIN • RIDE Technology
Carefully unpack and inspect the contents of your Follett ice machine. 1
Unpack
7/16"
7/16"
➊➋➌
➍➎
➏➐
DO NOT TILT ICE MACHINE
TO ACCESS BOLTS!
COMPRESSOR DAMAGE
WILL RESULT
Unpack ice machine
1. 1

5
BIN • RIDE Technology self-contained
Prepare the installation site. 2
➊
NEMA
5-15
➋
➌
1/4" per foot
(6,4 mm per 0,3 m)
7/8" ∅ (22,4mm)
➎3/8" ∅ (9,5mm)
➍
2 ft. x 1" OD
silicone tubing
and ttings
provided
3/8" chassis
drain must be
used
➌
Site preparation
Electrical ➊
• 120/60/1-5 amps
Potable water supply ➋ (3/8" push-in connection, 3/8" OD tubing required)
• 10-70 psi (69-483kpa)
• 45-90 F (7-32 C)
• Follett recommends the use of an in-line water ltration system (item# 00130286)
• This equipment is to be installed with adequate backow protection to comply with applicable
federal, state, and local codes
Drains: ➌ 3/4” Barb for silicone drain, 3/8” push-to-connect for chassis drain
• Minimum 8” radius on silicone drain line. Drain line from the ice machine must have at least
1/4” per foot pitch (6,4mm/0,3m).
Refrigeration lines ➍
• 7/8" ∅ (22,4 mm) diameter suction line (insulated) ➍
• 3/8" ∅ (9,5 mm) liquid line ➎
2.1
Provide drainage, water supply and electrical power to within 6 feet (2m) of
ice machine in accordance with local and national codes. Outdoor installation
of low side is not recommended and will void warranty.
Installation site requirements
2.1

6self-contained BIN • RIDE Technology
Prepare the bin. 3
Bin preparation
3" ∅
(76,2mm)
C
L
C
L
• Locate center of bin top
• Cut 3" (77,2mm) diameter hole in bin top
Bin top preparation
3.1
• Remove protective tape from
gaskets
Bin top preparation
3.2
➋
➊
➊
➌
• Apply gaskets ➊
• Install shuttle actuator ➋through top of
bin and secure with locking nut ➌
Bin top preparation
3.3
Prior to installing the docking assembly,
ensure that the drain tting is oriented (right
or left) correctly for your installation. An
optional straight drain tting is also supplied.
You may need to remove the back panel of
the docking assembly in order to re-orient or
change the drain tting. Replace back panel
prior to mounting the docking assembly.
BEFORE PROCEEDING

7
BIN • RIDE Technology self-contained
Install the docking assembly.
Docking assembly 4
Machine stand accessory
Wall bracket accessory
➊
➊
3/8˝ ∅
high pressure
line
7/8" ∅ low pressure line
2" (50,8 mm)
Stub Typ
1.81" (46 mm)
3.75" (95.3 mm)
2" (50,8 mm)
➋
• Mount docking assembly ➊
• ”Rough-in” the refrigerant piping ➋
2.1 Docking assembly
4.1
• Mount docking assembly to wall bracket
accessory
• Mount docking assembly to machine
stand accessory

8self-contained BIN • RIDE Technology
Transport tube
Install the ice transport tube. 5
1/4"
1'
➌
➍
➏
➐
➎
➋
➑
➒
➓
➊
Hot Water
160 F (71 C)
Ice transport tube tips
• Insulate entire length of ice transport tube ➊
• Secure ice transport tube ➋as needed to prevent dips and traps from forming.
For long tube runs see guide on page 13.
• Pitch ice transport tube at least 1/4" per foot (6,4mm/.3m) ➌
• Ice transport tube must drain towards ice machine
Ice transport tube to bin
• Be sure tube ends are square ➍
• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➎
before making connection to ease assembly
• Push ice transport tube onto ice machine nipple ➏
• Install hose clamp ➐
Ice transport tube to Ice machine
• Be sure tube ends are square ➑
• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➎
before making connection to ease assembly
• Push ice transport tube onto ice machine nipple ➒
• Install hose clamp ➓
Ice transport tube installation
5.1

9
BIN • RIDE Technology self-contained
Connect utilities to docking assembly. 6
External connections
3/4" barb x 3/4" FPT
1" Stand pipe/Drain
2 ft. x 1" OD
silicone tubing
Minimum 8"
radius
➍
3/4" MPT x 1" slip
➎
➌
➋
➊
➏
• Rough-in ice machine potable water
supply ➊. 3/8" push-in connection will be
made at included shut-off valve then at
back of docking station into solenoid.
• Remove access panel if necessary ➋.
• Connect the silicone tubing to the ice
machine 3/4" drain barb ➌.
• Assemble the 3/4" barb x 3/4" FPT to the
3/4" MPT x 1" slip. Connect the other end
of the silicone tubing to the 3/4" barb ➍.
• Connect the 1" slip tting to the 1" stand
pipe/drain ➎.
Note: Minimum 8" radius on silicone
drain line. Drain line from the ice machine
must have at least 1/4" per foot pitch
(6,4mm/0,3m).
• Apply Petrogel to barbed drain tting ➏
• Replace access panel.
Water and drain
6.1
Refrigerant
6.2
➊
• Braze supplied quick-connect lines onto
stub-ins ➊.
• Plug must be removed from John Guest
tting.
• Route 3/8" drain tubing through knockout
in back of docking station and insert fully
into John Guest tting connection at the
rear of the machine chassis. Route other
end of 3/8" drain tubing to drain.
• Drain must slope 1/4" inch per foot (6 mm
per 30,4 cm).
Chassis drain plumbing - required

10 self-contained BIN • RIDE Technology
Connect docking assembly to ice machine. 7
Internal connections
➊
• Evacuate line set.
• Connect self-sealing liquid and suction
line ttings ➊
Refrigeration lines
7. 3
➊
➋
• Slide ice machine into docking assembly
ensuring that drain tube is fully seated on
barbed drain tting ➊
• Insert ice transport tube all the way into
coupling and tighten nut rmly ➋
Ice transport tube installation
7. 1
Mount water
solenoid
➌
➋
➊
• Mount water solenoid to inside rear of
docking assembly using one screw ➊
• Insert potable water line into valve ➋
• Insert into push-in connection of water
solenoid ➌
Water line
7. 2
• Remove twist tie
• Carefully pass cord thru opening and plug
into wall outlet
Power cord
7. 4

11
BIN • RIDE Technology self-contained
• Position plate into opening and secure
with supplied screw
Power cord
7. 5
CLEANER FULL DRAIN CLOG HIGH PRES HIGH AMPS
SERVICE MAINT/CLEAN LOW WATER TIME DELAY SLEEP CYCLE MAKING ICE LOW BIN POWER ON
CLEAN
TDS
HIGH
LOW
• Set the TDS switch on the electrical box:
HIGH: for extended service life
LOW: for low-scale water
TDS switch
7. 6

12 self-contained BIN • RIDE Technology
Front cover
Install front cover to ice machine. 8
NOTICE
Ice machine MUST be sanitized prior to operation!
Consult Operation and Service Manual provided with ice machine for sanitizing instructions.
• Complete installation of condensing unit
or connection to rack system.
• Required rack system capacity at 0 F
(-18C) evaporator (EPR supplied by
installer).
1810N: 15,700 Btu/hr (3956 kcal/hr)
2110N: 18,200 Btu/hr (4586 kcal/hr)
Install condensing unit
8.1
➋➊
• Slide ice machine cover over machine
ensuring that tabs on back of cover
slip under louvers on back of docking
assembly ➊
• Insert and tighten two screws through
cover and into docking assembly ➋
Install ice machine front cover
8.2

13
BIN • RIDE Technology self-contained
➊
➋1/4"
1'
max. 2 ft (.6m)
• Pitch ice transport tube to allow melt water to drain towards ice machine ➊
• Secure insulated ice transport tube at least every 2 ft (.6m) to prevent dips or traps ➋
Long tube run recommendations

14 self-contained BIN • RIDE Technology

15
BIN • RIDE Technology self-contained

01157874R02
© Follett Products LLC 8/21
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com
Horizon, Horizon Elite, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge, RIDE and Vision are trademarks of Follett Products LLC.
Chewblet is a registered trademark of Follett Products LLC, registered in the US.