Freescale Semiconductor M68HC08 series User manual

MOTOROLA.COM/SEMICONDUCTORS
M68HC08
Microcontrollers
DRM045/D
Rev. 0
Using the ASB520
Designer Reference
Manual
MC68HC908QT2
Based Infrared
Remote Control
Reference PC Board
9/2003
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board DRM045
MOTOROLA 3
Motorola and the Stylized M Logo are registered trademarks of Motorola, Inc.
DigitalDNA is a trademark of Motorola, Inc.
This product incorporates SuperFlash® technology licensed from SST. © Motorola, Inc., 2003
Using the ASB520 MC68HC908QT2 Based
Infrared Remote Control Reference
PC Board
Reference Design
By: Bill Lucas
Motorola Transportation and Standard Products Group
Austin, TX
To provide the most up-to-date information, the revision of our documents on
the World Wide Web will be the most current. Your printed copy may be an
earlier revision. To verify you have the latest information available, refer to:
http://motorola.com/semiconductors
The following revision history table summarizes changes contained in this
document. For your convenience, the page number designators have been
linked to the appropriate location.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

DRM045 Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board
4 Revision History MOTOROLA
Revision History
Revision History
Date Revision
Level Description Page Number(s)
September,
2003 N/A Initial release N/A
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board DRM045
MOTOROLA Table of Contents 5
Designer Reference Manual — DRM045
Table of Contents
Section 1. Introduction and Setup
1.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2 About this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.3 Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Section 2. Operational Description
2.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2 Push Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3 LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3.1 Red Activity Indicator LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3.2 Infrared LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4 Header and Jumpers Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5 Microcontroller Current Monitor Jumper Block . . . . . . . . . . . . . . . . . 14
Section 3. Pin Description
3.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2 16-Pin Connector J1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Section 4. Schematic and Parts List
4.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.2 Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.3 Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Section 5. Design Considerations
5.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.2 Grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.3 Infrared and Visible LED Drive Circuit . . . . . . . . . . . . . . . . . . . . . . . 21
5.4 Switch Circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Section 6. System Testing
6.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.2 Hardware/Software Testing Summary . . . . . . . . . . . . . . . . . . . . . . . 25
6.3 FLASH Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.4 LED and Push Button Test Code . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.5 DVD Player Control Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

DRM045 Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board
6 Table of Contents MOTOROLA
Table of Contents
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board DRM045
MOTOROLA Introduction and Setup 7
Designer Reference Manual — DRM045
Section 1. Introduction and Setup
1.1 Introduction
Motorola’s ASB520, MC68HC908QT2 Infrared Remote Control Reference PC
Board and software are designed to demonstrate how a simple, limited
function, dedicated remote control system could be designed. The objective is
to keep the design simple so a user can pick portions of interest to his design
and turn them into an application specific system. This system is specifically
programmed to control an APEX model 1201 DVD player.
A few of the more noteworthy features of the reference PC board are listed as
follows:
• 8-pin MC68HC908QT2 microcontroller
• Infrared LED and driver
• Visible LED to show activity
• Six user push buttons
• MON08 programming interface for in-circuit FLASH programming
• Battery holder for 3-AA cells
• Microcontroller current monitor jumper block
A photograph of the reference PC board appears in Figure 1-1.
1.2 About this Manual
Key items can be found in the following locations in this manual:
• Setup instructions are found in 1.3 Setup Guide.
• Schematics are found in 4.2 Schematic.
• Pin assignments for MON08 connector J1 are shown in Table 3-1.
MON08 Pin Assignments.
• User interfaces are described in 2.3 LEDs.
• For those interested in the design aspects of the reference PC board’s
circuitry, a description is provided in Section 5. Design
Considerations.
• System testing, hardware and software, are described in detail in
Section 6. System Testing.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

DRM045 Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board
8 Introduction and Setup MOTOROLA
Introduction and Setup
Figure 1-1. MC68HC908QT2 IR Reference PC Board Photograph
1.3 Setup Guide
Setup for the reference design PC board can be broken into two parts.
• The first is normal user operation mode.
• The second is MC68HC908QT2 FLASH programming configuration.
FLASH programming is explained in Section 6. System Testing.
It is assumed for user operational mode, the MC68HC908QT1 has been
programmed with the remote control program. If not, refer to Section 6.
System Testing for FLASH programming information.
Figure 2-1. PC Board shows the locations of the various jumper blocks and
MON08 connector.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Introduction and Setup
Setup Guide
Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board DRM045
MOTOROLA Introduction and Setup 9
For user operation mode, shorting jumpers need to be installed to jumper
blocks JP1–JP4. Shorting jumper block JP1 is not necessary if the small PC
board trace under jumper block JP1, on the bottom side of the PC board, has
not been cut for microcontroller current monitoring.
Installation of 3-AA Alkaline batteries into the battery holder mounted on the
bottom of the PC board is also required for setup. Note battery polarity on the
battery holder. The PC board is now ready for use as an infrared remote
control.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

DRM045 Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board
10 Introduction and Setup MOTOROLA
Introduction and Setup
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board DRM045
MOTOROLA Operational Description 11
Designer Reference Manual — DRM045
Section 2. Operational Description
2.1 Introduction
The following subsections describe the operation of the ASB520,
MC68HC908QT2 infrared remote control reference design system. LEDs,
switches,jumperblocksandFLASHprogrammer headers,andcurrentmonitor
jumper block are described here. Figure 2-1 shows the locations of these
items.
2.2 Push Buttons
There are six push button switches resident on the lower portion of the
reference PC board. They arelabeled as switches SW1–SW6 on the PC board
schematic. Each button has a dedicated function. The switches are labeled as
POWER, PAUSE, PLAY, REVERSE, STOP, and FORWARD. These labels
describe the button’s operation function related to control of a DVD player.
2.3 LEDs
Thereare two LEDs locatedin theupperrighthand corner of thePC board.The
LED labeled D1 is an infrared LED and the one labeled D2 is a visible red LED
and is used to show system activity.
2.3.1 Red Activity Indicator LED
D2 is a visible red LED and is used to show IR LED activity. It blinks as long
any push button is depressed
2.3.2 Infrared LED
D1 is an infrared LED. It is modulated to control the DVD.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

DRM045 Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board
12 Operational Description MOTOROLA
Operational Description
Figure 2-1. PC Board
JP1
JP2
JP4
JP3
J1
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Operational Description
Header and Jumpers Blocks
Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board DRM045
MOTOROLA Operational Description 13
2.4 Header and Jumpers Blocks
There is one 16-pin header (2 x 8-pin), J1, and four 2-pin jumper blocks,
JP1–JP4, on the PC board. See Figure 2-1 for their locations on the PC board.
The header and jumper functions are described as follows.
J1: Jumper block J1 is used to program the MC68HC908QT2, located in
the center of the PC board. The connections to this board follow the
standard MON08 connector scheme. It is also used to put the ASB520
system into test mode. In a production environment, J1 could be
replaced by a “bed of nails” test fixture to reduce PC board parts costs.
JP1: Jumper block JP1 is on the PC board measure the current consumed
by the microcontroller. Its primary purpose is to measure stop current of
the microcontroller. A small trace on the bottom of the PC board must
be cut to use this feature. When using this feature to measure stop
current you should remove shorting jumper JP2. Removing the shunt
from JP2 removes the system’s 470 µF bulk capacitor. Removing that
capacitor will improve accuracy of the current measurement, as large
capacitors have leakage current associated with them. Select the
lowest voltage rating bulk capacitor for your circuit as possible because
lower voltage rated ones tend to have less leakage than higher voltage
ones for a given capacitance value.
JP2: Jumper block JP2 disconnects the bulk capacitor during FLASH
programming and optionally during stop current monitoring. The value
of the capacitor is large enough to cause power switching issues when
using the Cyclone programmer. During the programming procedure,
the Cyclone programmer cycles power to the target PC board. Large
value bulk capacitors greater than approximately 100 µF present
excessive currents to the Cyclone programmer and interfere with the
POR circuit of the target’s microcontroller as voltage on larger
capacitance devices do not discharge fast enough during voltage
cycling.
Thepurposeforthebulk capacitoristwofold:Firstis tendstohelplower
the effects of the battery’s internal resistance during periods of high
current demands while the IR LED is being modulated. This is a
particularbenefittoward thebattery’sendoflifeperiod,whenitsinternal
resistance is increasing. Second, if a system uses RAM to store user
information, the bulk capacitor will retain voltage to the microcontroller
during battery changes.
JP3: Jumper block JP3 disconnects pullup resistor, R9, during FLASH
programming.
JP4: Jumper block JP4 disconnects LED drive circuitry during FLASH
programming.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

DRM045 Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board
14 Operational Description MOTOROLA
Operational Description
2.5 Microcontroller Current Monitor Jumper Block
Jumper block JP1 is intended as a connection on the PC board to measure the
stopcurrent of theMC68HC908QT2.Tousethe feature,youmustcut the small
PC board trace located on the bottom side of the PC board between the two
pins of the jumper block. After cutting the trace, and when not using an amp
meter to measure system current a shunt must be installed on JP1.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board DRM045
MOTOROLA Pin Description 15
Designer Reference Manual — DRM045
Section 3. Pin Description
3.1 Introduction
There is one connector resident on the control board, labeled J1. It is the
MON08 connector. The following subsection describes signals on connector
J1.
3.2 16-Pin Connector J1
Signals to and from the MON08 connector are grouped together on 16-pin
(2 x 8-pin) ribbon cable connector J1. Pin assignments for connector J1 are
shown in Table 3-1. In a production environment, J1 could be replaced by a
“bed of nails” test fixture to reduce PC board parts costs.
Table 3-1. MON08 Pin Assignments
Pin Number Function
1, 3, 4, 5, 7, 9, 11,14, 16 No connect
2GND
6VTST (PTA2)
8COM(PTA0)
10 MOD1 (PTA4)
12 MOD0 (PTA1)
13 OSC1 (PTA5)
15 VDD
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

DRM045 Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board
16 Pin Description MOTOROLA
Pin Description
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board DRM045
MOTOROLA Schematic and Parts List 17
Designer Reference Manual — DRM045
Section 4. Schematic and Parts List
4.1 Introduction
Schematic and parts list detail are documented in this section.
4.2 Schematic
A schematic of the reference design PC board appears in Figure 4-1. Unless
otherwise specified, capacitor values are in microfarads, resistor values are in
ohms. All resistors are specified as 1/4-watt ± 5%, and interrupted lines coded
with the same letters are electrically connected.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

DRM045 Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board
18 Schematic and Parts List MOTOROLA
Schematic and Parts List
Figure 4-1. ASB520 PC Board Schematic
Vdd
SW3
FWD
PTA2
PTA5
PTA5
R7
10
PTA0
Vbat
U1 NITRON_8_PIN_ADC
3 2
5 6 7 8
4 1
PTA4/OSC2/AD2/KBI4 PTA5/OSC1/AD3/KBI5
PTA2/IRQ/KBI2
PTA1/AD1/TCH1/KBI1 PTA0/AD0/TCH0/KBI0
Vss
PTA3/RST/KBI3
Vdd
JP1
Idd_TEST
1 2
12
Vdd
SW6
REV
Vdd
R1 47K
PTA2
Vdd
PTA1_ATD1
R2 330
R4 1K
R15 1k R13 220
R6 470
R9 3.3K
SW1
POWER
C2
0.1
R12 2.2k
Q2
2N3906
JP3
SW_DISC
1 2
12
J1
MON08 CONNECTOR
1 3 5 7 9
11 13 15 16
14 12 10 8 6 4 2
1 3 5 7 9 11 13 15 16
14 12 10
8 6 4 2
JP4
IR_DISC
1 2
12
R3 47
SW2
PLAY
+
C1
470uF
PTA1_ATD1
JP2
CAP_DISC
1 2
12
R14 470
PTA4
X1 16MHz
BATTERY
BAT1
12 +-
Q1 2N3904
R11 4.7K
Vdd
R5 47K
R10
10M
PTA1_ATD1
PTA4
D1
IR_LED
D2
RED
SW5
PAUSE
PTA0
R8 47K
SW4 STOP
Vbat
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

Schematic and Parts List
Parts List
Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board DRM045
MOTOROLA Schematic and Parts List 19
4.3 Parts List
The following parts list describes the parts content for the IR reference PC
board.
Table 4-1. Reference PC Board Parts List
Designators Qty. Description Manufacturer Part Number
BAT1 1 3-AA Battery Holder Digi-Key 2464K-ND
C1 1 470 µF [email protected] Digi-Key P5508-ND
C2 1 0.1 µF Capacitor Digi-Key 399-2127-ND
D1 1 Infrared LED Digi-Key 160-1061-ND
D2 1 Red LED Digi-Key 160-1061-ND
J1 1 2 x 8 Pin Header(1) Digi-Key S2211-36-ND(1)
JP1–JP4 4 2 Pin Header(1) Digi-Key S1211-36-ND(1)
Q1 1 2N3904 Digi-Key 2N3904-ND
Q2 1 2N3906 Digi-Key 2N3906-ND
R1, R8, R5 3 47K Ohm Resistor(2) Digi-Key 47QBK-ND
R3 1 47 Ohm Resistor(2) Digi-Key 47QBK-ND
R4, R15 2 1K Ohm Resistor(2) Digi-Key 1.0KQBK-ND
R13 1 220 Ohm Resistor(2) Digi-Key 220QBK-ND
R2 1 330 Ohm Resistor(2) Digi-Key 330QBK-ND
R6, R14 2 470 Ohm Resistor(2) Digi-Key 470QBK-ND
R7 1 10 Ohm Resistor(2) Digi-Key 10QBK-ND
R9 1 3.3K Ohm Resistor(2) Digi-Key 3.3KQBK-ND
R11 1 4.7K Ohm Resistor(2) Digi-Key 4.7KQBK-ND
R10 1 1 Meg Ohm Resistor(2) Digi-Key 1.0MQBK-ND
R12 1 2.2K Ohm Resistor(2) Digi-Key 2.2KQBK-ND
SW1–SW6 6 Momentary Push Button Switch Digi-Key CKN9009-ND
U1 1 Nitron 8-pin DIP with A/D and 1.5K FLASH Digi-Key MC68HC908QT1CP
X1 1 16.00 MHz Resonator Digi-Key X908-ND
No Designator (optional) 1 8-pin socket for U1 Digi-Key A400-ND
No Designator 1 2-56 x 3/8” nylon screw Any Any
No Designator 1 2-56 nylon nut Any Any
No Designator 1 Tape, double-sided foam 1/8” x 1”(3) Digi-Key 3M4008-ND
No Designator 1 ASB520 Bare PCB DS Electronics ASB520
No Designator 4 Shunts for JP1–JP4 Digi-Key S9000-ND
No Designator 3 AA Alkaline Battery Any Any
1. Shipped in strips of 36 x 1 or 36 x 2. Cut to length.
2. All resistors are 1/4 W with a tolerance of 5% unless otherwise noted.
3. Cut to size.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

DRM045 Using the ASB520 MC68HC908QT2 Based Infrared Remote Control Reference PC Board
20 Schematic and Parts List MOTOROLA
Schematic and Parts List
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...