Freescale Semiconductor Windows Embedded CE 6.0/Windows CE 5.0 i.MX31 PDK... User manual

i.MX31 PDK 1.4
Windows Embedded CE 6.0/
Windows CE 5.0
Quick Start Guide
3StackQS_WinCE.book Page 1 Sunday, September 28, 2008 1:58 PM

Information in this document is provided solely to enable system and software implementers to use Freescale Semicon-
ductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any inte-
grated circuits or integrated circuits based on the information in this document.
Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale
Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any partic-
ular purpose,nor does FreescaleSemiconductor assume any liability arising out of the applicationor use of any product
or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental dam-
ages. “Typical” parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and
do vary in different applications and actual performance may vary over time. All operating parameters, including “Typ-
icals”, must bevalidated for each customer application by customer’s technical experts. Freescale Semiconductor does
not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not de-
signed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semi-
conductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use
FreescaleSemiconductor products for anysuch unintended or unauthorized application, Buyer shall indemnify andhold
Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
Federal Communications Commission Radio Frequency Interference Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) this device must accept any interference received, including interference that might cause undesired operation.
Changes or modifications to this equipment not expressly approved by Freescale could void the user’s authority to op-
erate the equipment.
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names
are the property of their respective owners. Microsoft and Windows are registered trademarks ofMicrosoft Corporation.
RealView is a registered trademark of ARM Limited. ARM11 is the trademark of ARM Limited. The ARM logo is a
registered trademark of ARM Ltd.Wi-Fi is aregisteredtrademarkof the Wi-Fi Alliance. Bluetoothis a registered trade-
mark of the Bluetooth SIG, Inc., and is used under license. Wi-Fi CERTIFIED is a trademark of the Wi-Fi Alliance.
© Freescale Semiconductor, Inc. 2007 - 2008. All rights reserved.
How to Reach Us:
Home Page:
www.freescale.com
E-mail:
[e-mail]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
[phone] or [phone]
[e-mail]
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
[phone] (English)
[phone] (English)
[phone] (German)
[phone] (French)
[e-mail]
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku,
Tokyo 153-0064, Japan
0120 191014 or [phone]
[e-mail]
Asia/Pacific:
Freescale Semiconductor China Ltd.
Exchange Building 23F
No. 118 Jianguo Road
Chaoyang District
Beijing 100022
China
[phone]
[e-mail]
For Literature Requests Only:
Freescale Semiconductor Literature Distribution
Center
P.O. Box 5405
Denver, Colorado 80217
1-800-521-6274 or 303-675-2140
Fax: [phone]
[e-mail]
3StackQS_WinCE.book Page 2 Sunday, September 28, 2008 1:58 PM

1
i.MX31 PDK 1.4 Quick Start Guide, Rev. 1.4
1 About the Boards 3
About the 3-Stack Platform System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
CPU Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Debug Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Personality Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2 Getting Started 13
Unpack the Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CD-ROM Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Provide a Development PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3 Build the Platform 17
Build a Development Platform: Assemble Three Boards. . . . . . . . . . . . . . . . . . 17
Connect Personality Board to Debug Board. . . . . . . . . . . . . . . . . . . . . . . . .18
Connect CPU Board to Debug Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Connect Development Platform to PC; Run Preloaded Image. . . . . . . . . . .20
Build a Demo Platform: Assemble Two Boards. . . . . . . . . . . . . . . . . . . . . . . . . 21
Connect CPU Board to Personality Board . . . . . . . . . . . . . . . . . . . . . . . . . .22
Connect Power Supply; Run Preloaded Demo . . . . . . . . . . . . . . . . . . . . . .23
4 Using the Demo Image 25
Multimedia Codecs Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Touch Pad Calibration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Downloading Multimedia to the 3-Stack Board . . . . . . . . . . . . . . . . . . . . . . . . .28
Using Active Sync. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Using an SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Using a USB Memory Stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Running the Demo Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Running the TV-Out Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Running the Rotate Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Changing the Windows CE 5.0 or Windows Embedded CE 6.0 Demo Image
Version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Ready to Begin Your Development? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3StackQS_WinCE.book Page 1 Sunday, September 28, 2008 1:58 PM

2
i.MX31 PDK Kit Configuration Guide
3StackQS_WinCE.book Page 2 Sunday, September 28, 2008 1:58 PM

3
i.MX31 PDK 1.4 Quick Start Guide
1
About the Boards
This chapter provides detailed information about the three boards (CPU, Debug,
Personality) and the locations of the connectors and switches for each.
CAUTION Your PDK arrives housed in a plastic device enclosure, which under
normal circumstances you should not remove. However, the PDK
documentation set includes information for board-level components, and
also explains in some documents how to assemble the boards into the
enclosure. Should you need to work directly with the boards, please use
great caution in handling the components:
– To remove or work with the boards, use static precautions.
– To remove or add the enclosure, first read the enclosure assembly instructions
carefully and note which areas are delicate, such as the speakers.
About the 3-Stack Platform System
Freescale introduces the 3-Stack Platform System, which you use to develop multimedia
and connectivity applications using the i.MX31 Applications Processor and the MC13783
Audio and Power Management device.
The 3-Stack Platform System decreases the time between first development and final
product release by providing you (as the system designer) with a near-to-final product
design, which you can use as a development platform for software and hardware.
There are two Board Support Packages (BSP) for the 3-Stack Platform System, with one
BSP for Microsoft® Windows CE™ 5.0/Windows Embedded CE™ 6.0, and one BSP for
Linux operating systems. These BSPs contain drivers optimized for multimedia operations
using the i.MX31 and MC13783 devices.
Freescale's 3-Stack Platform System consists of three small boards: CPU, Debug, and
Personality.
• A CPU board contains the i.MX31 CPU, memories, and the MC13783 Power
Management IC (PMIC).
• A Debug board provides the debug interfaces (such as JTAG), and also has a CPLD
that implements an external Ethernet and serial controller for debug purposes.
• The Personality board implements the functionality of the 3-Stack board, and
contains hardware for Wi-Fi connectivity, FM receiver, and so on. The Personality
board can be modified to meet your specific requirements without the need to modify
the other two boards (CPU, Debug). The Personality board was designed to support
3StackQS_WinCE.book Page 3 Sunday, September 28, 2008 1:58 PM

About the Boards
About the 3-Stack Platform System
4i.MX31 PDK 1.4 Quick Start Guide
common multimedia applications, and has a 2.8-inch VGA display, image sensor
camera, Wi-Fi CERTIFIED™ IEEE 802.11™ b/g standards, FM receiver, SD Card
connector, USB OTG, USB Host, 2.4 QVGA smart display panel connector, ATA
connector and TV-Out connector. As the 3-Stack platform continues to evolve, more
Personality boards will be created to meet new multimedia requirements. Table 1.2
lists 3-Stack platform features in more detail.
Table 1.1 3-Stack Platform Features
Details
All boards • Near to final product form-factor demonstration
modules and working platforms.
• Solid reference schematics that closely resemble
final products to aid customers' designs.
CPU board • i.MX31 ARM11™Applications Processor
• MC13783 Atlas power management chip
• 256 MB of NAND Flash Memory
• 128 MB of 32 bit DDR SDRAM memory
• 37.914 mm x 67.517 mm
Personality board • Peripheral components
• Interface connectors
• 71.428 mm x 129.462 mm
Debug board • Two RS-232 interfaces
• 10/100 Base-T Ethernet connector
• Current measure connectors
• 71.400 mm x 174.900 mm
Expansion Headers • Utilizing reliable high density connector to interface
between boards, 3 board assembly for software
development and 2-board assembly (without debug
board) for demonstration
Battery Support • +4.2 V 2400mAh Battery power supply and Battery
Charging Function
LCD Display • 2.8 inch TFTLCD display panel with touch panel and
LED backlight
Smart LCD Connector • 2.4 inch QVGA smart display panel connector
Camera Interface • Image sensor camera connector
Selectable Clock
Sources
• Two selectable system clock sources: 32.768 KHz
and 26 Mhz
3StackQS_WinCE.book Page 4 Sunday, September 28, 2008 1:58 PM

About the Boards
About the 3-Stack Platform System
5
i.MX31 PDK 1.4 Quick Start Guide
Debug Port •RealView
®-ICE debug support
Video and Audio
Stereo
• Stereo microphone jack, headphone and video jack,
stereo and mono (ear piece) speaker terminals
GPS Connector • One connector to outboard GPS module
FM Receiver
TV Out • TV decoder that supports 8-bit color, NTSC and PAL
formats
PC Card Expansion • SD card connectors, with card sense
Keypad • Onboard keypad and keypad connector
Network Support • Onboard Wi-Fi CERTIFIEDFter IEEE 802.11 b/g
standards and Bluetooth(r) Core Specification
Version 2.0 + EDR (enhanced data rate)
combination module
• One Ethernet jack connector (for application/debug)
USB • One USB OTG high-speed transceiver with mini-
USB connector
• One USB high-speed host transceiver, with
standard USB host connector
ATA Support ATA5 controller with
• One 44-position dual row 2 mm header for small
form-factor disk drivers
• One 40-pin ZIF connector for Toshiba HDD
Accelerometer • Onboard accelerometer with sensitivity in three
separate axes (X, Y, Z)
Serial Port Two RS-232 interfaces with DB-9 connectors
• One RS-232 interface is driven by a UART channel
internal to the MX31, and it supports DCE with
optional full modem controls
• The other RS-232 interface is DTE with optional full
modem controls
Table 1.1 3-Stack Platform Features
Details
3StackQS_WinCE.book Page 5 Sunday, September 28, 2008 1:58 PM

About the Boards
About the 3-Stack Platform System
6i.MX31 PDK 1.4 Quick Start Guide
Cables • 5.0V/2.4A universal power supply kit
• RS-232 standard serial cable
• High Speed USB cables with mini-AB connectors for
OTG
• High speed cable with standard A-to-mini-B
connectors
• Mini-USB adaptor
• Jack to RCA audio/video cable
• Ethernet cables (2) with RJ45-8 connectors
Software • Sample Windows® embedded CE binary image
from Freescale
• Windows embedded CE BSP available from
Freescale
Application
Development Tools
• ATK software
• Platform Builder 5.0/6.0
• Visual Studio 2005
Table 1.1 3-Stack Platform Features
Details
3StackQS_WinCE.book Page 6 Sunday, September 28, 2008 1:58 PM

About the Boards
CPU Board
7
i.MX31 PDK 1.4 Quick Start Guide
CPU Board
Figure 1.1 CPU Board
You use the J1 board-to-board connector (500 pins) to connect the CPU board to either of
the other two boards:
• Connect the CPU board to a Personality board, for running demos (no Debug board
is needed).
• Connect the CPU board to a Debug board, (and connect the Personality board to the
Debug board) for developing software. The Personality board plugs into the other
side of the Debug board.
J1 Board-to-Board Connector
CPU
Board Top
Bottom
3StackQS_WinCE.book Page 7 Sunday, September 28, 2008 1:58 PM

About the Boards
Debug Board
8i.MX31 PDK 1.4 Quick Start Guide
Debug Board
Figure 1.2 Debug Board
To Personality Board Connector CN74
Current Measure J3
MX31 JTAG CN1
SW5–SW10 See Table 1.5
3.3V LED D9 Power-On S4 DC Power LED D11
DC Power J2
Ethernet J1
UART CON4
female
UART CON3
male
Device MAC
Address
Personality
CPLD JTAG
CN3
CPLD Test BT
Debug Reset S2
CPLD Test BT
Power S1
System Reset S3
CPLD LEDs D1–
SW4 See Table 1.4
Debug
Board
TOP
Bottom
P1
P2
Resettable Fuse F1
To CPU Board Connector
Debug CPLD JTAG CN2
Address
MAC
Device
3StackQS_WinCE.book Page 8 Sunday, September 28, 2008 1:58 PM

About the Boards
Debug Board
9
i.MX31 PDK 1.4 Quick Start Guide
Table 1.2 Debug Board Physical Features
Type Physical Feature
Switches • S1: Power button
• S2: Debug board reset button
• S3: System reset switch
• S4: Power-on switch
• SW4: Enable switch
Connectors • J1:10/100 Base-T Ethernet RJ45 connector
• J2: 5.0V DC power connector
• J3: Current measure connector
• J4: 500-pin connector to CPU board
• P1: WEIM Address measure connector
• P2: WEIM Data measure connector
• CN1: i.MX31 JTAG connector
• CN2: Debug board CPLD JTAG connector
• CN3: Personality board CPLD JTAG connector (Reserved)
• CN74: 500-pin connector to Personality board
• CON4: UART (DCE) DB9 female connector
LEDs • D1–D8: LEDs for CPLD debug
• D9: LED for Debug board 3.3V power
• D11:LED for DC power supply
Buttons • BT1, BT2: Test buttons for CPLD
Fuse • F1: Resettable Fuse
3StackQS_WinCE.book Page 9 Sunday, September 28, 2008 1:58 PM

About the Boards
Debug Board
10 i.MX31 PDK 1.4 Quick Start Guide
Table 1.3 Debug Board SW4 Switch
Switch Setting Effect
SW4-1 UART Port Select ON Selects serial port UART (DCE) CON4
SW4-8 Power Enable ON Power is supplied to all three boards.
OFF Power is only supplied to the Debug
board.
Table 1.4 Boot Mode Setting (SW5–SW10)
Boot Mode
Device
SW5 Boot4
SW6
Boot3
SW7
SW8 SW9 SW10
UART/USB
bootloader
X0 0 0 0 0
8-bit NAND Flash
(2KB page) Ext
X1 0 0 0 0
3StackQS_WinCE.book Page 10 Sunday, September 28, 2008 1:58 PM

About the Boards
Personality Board
11
i.MX31 PDK 1.4 Quick Start Guide
Personality Board
Figure 1.3 Personality Board
Bluetooth
Antenna
E2
Audio/Video
J19
USB OTG
J10
USB Host
J18
GPS CN13
GiantPlus QVGA Smart
Display J15
CMSO Sensor
CN14 (underneath
LCD)
Debug Port forWiFi
and Bluetooth CN16
ZIFF Connector
forHDD CN70
WVGA (not populated)
Keypad Connector CN20
Resettable
Fuse F1
TOP
On-Board
Keypad S1–S7
Fast
Ethernet
J16
SD Card
Socket
CN31
DC
Power
J12
HDD Connector CN12
Board-to-Board
Connector CN73
Coin Cell Battery
B1
Bottom
Personality
Board
WiFi Antenna
E1
Camera
Reset Button
Epson VGA Display
Connector
(underneath LCD)
Battery Connector
3StackQS_WinCE.book Page 11 Sunday, September 28, 2008 1:58 PM

About the Boards
Personality Board
12 i.MX31 PDK 1.4 Quick Start Guide
Table 1.5 Personality Board Physical Features
Type Physical Feature
Connectors • CN12: 44-position dual row, 2 mm header for HDD
• CN13: GPS module connector
• CN14: 2.0 M pixel CMOS sensor connector
• CN16: Debug port for WiFi and Bluetooth module
• CN31: SD card socket
• CN70: 40-pin ZIF connector for HDD
• CN73: 500-pin connector to CPU Engine board (in demo
configuration) or Debug board (in development configuration)
• J10: Mini-USBOTG high speed connector
• J12: 5.0 VDC power connector
• J14: Epson VGA display connector
• J15: Giantplus QVGA smart display connector
• J16: 10/100 BT Fast Ethernet Connector
• J18: Standard USB host high speed connector
• J19: Audio and video connector
Battery • B1: Coin cell battery
Buttons • S7–S17: Onboard keypad
Fuse • F1: Resetable fuse
Antennas • E1: WiFi Antenna
• E2: Bluetooth antenna
3StackQS_WinCE.book Page 12 Sunday, September 28, 2008 1:58 PM

13
i.MX31 PDK 1.4 Quick Start Guide
2
Getting Started
Unpack the Kit
The 3-Stack Platform System is shipped with the items listed in Table 2.1.
Verify that all the items are contained in the package. See Figure 2.1.
Take out the three boards from their anti-static bags and check the boards for any visible
damage.
Table 2.1 Contents
Type Items
Boards • CPU board
• Debug board
• Personality board
Cables • RS-232 serial cable
• Ethernet straight cable
• High-speed USB cables with mini AB
connectors for OTG
• High-speed cable with standard A to
mini B connectors
• Mini-USB adaptor
• Jack to RCA audio/video cable
Power Supply • 5.0V/2.4A universal power supply kit
• CD-ROMs: Content CD, Platform
Builder Trail CD, and Visual Studio
2005 Trial CD
• End-User License Agreement
• Quick Start Guide (this document)
• Warranty card
• Freescale Support card
3StackQS_WinCE.book Page 13 Sunday, September 28, 2008 1:58 PM

Getting Started
Unpack the Kit
14
i.MX31 PDK 1.4 Quick Start Guide
Figure 2.1 PDK Kit Contents
RS-232
CD-ROM
A to Mini B
USB Cable
CPU
Board
Debug
Board
Universal
Power
Supply
Personality
Board
Ethernet
Straight Cable
Mini-AB
Jack to RCA
Audio/Video Cable
A to Mini-B
USB Cable
USB OTG
3StackQS_WinCE.book Page 14 Sunday, September 28, 2008 1:58 PM

Getting Started
CD-ROM Contents
15
i.MX31 PDK 1.4 Quick Start Guide
CD-ROM Contents
Table 2.3.identifies the items on the CD-ROM set.
Table 2.2 Development PC Requirements
Type Requirement
Product
Documentation
• i.MX31 PDK Product Brief
• Bill of Materials, Schematics, and Gerber files for
CPU Board, Personality Board, and Debug Board
• i.MX31 Demo Image Readme for Windows CE 5.0
and Windows Embedded CE 6.0
• i.MX Platform Hardware User’s Guide
• i.MX31 PDK Quick Start Guides for Windows CE
5.0/Windows Embedded CE 6.0 (this document)
• i.MX31 PDK Release Notes for Windows CE 5.0
and Windows Embedded CE 6.0
• i.MX31 PDK User’s Guides for Windows CE 5.0
and Windows Embedded CE 6.0
• i.MX31 PDK Reference Manuals for Windows CE
5.0 and Windows Embedded CE 6.0
• i.MX31 PDK Hello World Application Notes for
Windows CE 5.0 and Windows Embedded CE 6.0
• Data sheets for the i.MX31 PDK Platform’s non-
Freescale components
• i.MX Platform Advanced ToolKit (ATK) User’s
Guide
Software
Development Tools
• Microsoft Platform Builder, versions 5.0/6.0
• Visual Studio 2005
• Windows CE 6.0/Windows Embedded CE 6.0 SDK
installation file
• Advanced ToolKit (ATK) software
3StackQS_WinCE.book Page 15 Sunday, September 28, 2008 1:58 PM

Getting Started
Provide a Development PC
16
i.MX31 PDK 1.4 Quick Start Guide
Provide a Development PC
To develop applications using the 3-Stack development kit, get a PC with the
requirements listed in Table 2.3.
Table 2.3 Development PC Requirements
Type Requirement
Operating System • Windows XP Professional with Service Pack 1
or
Windows 2000 Professional with Service Pack 4
Network • Internet access
Software Tools • Microsoft .NET Framework, version 1.1
PC HW • 933 MHz Pentium II or later processor;
2 GHz processor recommended
• 512 MB of RAM;
1 GB recommended
• 1 GB of available space required on system drive
• 18 GB of available hard-disk space
•DVDROMdrive
• 1024x768 or higher resolution display with 256
colors
3StackQS_WinCE.book Page 16 Sunday, September 28, 2008 1:58 PM

17
i.MX31 PDK 1.4 Quick Start Guide
3
Build the Platform
This chapter explains how to connect the three types of 3-Stack boards (Debug,
Personality, CPU) together, to make either a development platform (Personality board +
CPU board + Debug board), or a demonstration platform (Personality board + CPU
board); and how to connect the 3-Stack platform to your PC. See Figure 3.1.
Figure 3.1 3-Stack Platform Configurations
The three 3-Stack boards in your development kit may already be assembled. If the three
boardsare already assembled, review the procedures in the following sections, and be sure
to configure the Debug board appropriately.
• To build a development platform, follow the procedures in “Build a Development
Platform: Assemble Three Boards” on page 17.
• To build a demonstration platform, follow the procedures in “Build a Demo
Platform: Assemble Two Boards” on page 21.
Build a Development Platform: Assemble
Three Boards
This section explains how to connect the Personality, Debug, and CPU boards.
Development
Configuration
Personality Board
Debug Board
CPU Board
Demo
Configuration
Personality Board
CPU Board
3 Board Stack 2 Board Stack
3StackQS_WinCE.book Page 17 Sunday, September 28, 2008 1:58 PM

Build the Platform
Build a Development Platform: Assemble Three Boards
18
i.MX31 PDK 1.4 Quick Start Guide
Connect Personality Board to Debug
Board
The Personality board connects to the Debug board using a 500-pin connector. The
connector is keyed to avoid misconnection, so there is only one way to connect these
boards. Connect the Personality board to the Debug board. The maximum allowable angle
for mating and unmating boards is 10 degrees. See Figure 3.2. For additional information,
see: http://samtec.com/ftppub/TESTRPT/tc076--1254reportrev3.pdf.
Figure 3.2 Install Personality Board onto Debug Board
Personality
Board
Debug
Board
Align boards
PersonalityBoard
Debug
Board
1
2Connect boards
Personality
Board
Debug
Board
3StackQS_WinCE.book Page 18 Sunday, September 28, 2008 1:58 PM