Frico Aquaztrip H User manual

Content Page
Delivery control 2
View 2
Mounting 3
Water connection 4
False ceiling adaptation 5
Installation instruction
Installationsvejledning
Montageanvisning
Asennusohje
Montageanleitung
Instruzioni di montaggio
Instruction de montage
Aquaztrip H, L
Original instructions

Installation instruction
Delivery control
Control the delivery!
Example of delivery code:
Aquaztrip H & Aquaztrip L - 60 - 10 - 1 - 4,8 m.
Width, cm
Water connection, mm
Pipe connection type
Length, m
There are also included support sleeves that must be used in every connection pipe.The amount of pendulums/
angle brackets panel or outer depends on the length. Up to 4,0 m. are 4 pieces included of each. At lengths above
4,0 m. are 6 pieces of each included.
View
Aquaztrip H and Aquaztrip L could be mounted either direct to the concrete or hanging in pendulums. Aquaztrip L
could also be integrated into false ceilings.
Way of mounting Included mounting details
Free mounted 4-6 adjustable pendulums (alternative chains)
4-6 angle brackets panel
Direct to ceiling 4-6 angle brackets outer
4 wire springs included for all panels with vertical water connections.
Direct to concrete
Free hanging
Integrated into false ceilings
Aquaztrip H, L
2

Installation instruction
Mounting with adjustable pendulums
1.- Measure and drill into the ceiling for the strips/pa-
nels brackets. 4 pieces for lengths up to 4,0 m., 6
pieces for longer units.
Mounting direct to concrete
1.- Measure and drill into the concrete
for angle brackets outer. Use 6 pie-
ces with lengths above 4,0 m.
5.- Adjust the length of the pendulums. Also adjust af-
ter the false ceiling height if it’s mounted into this.
2.- Screw up the brackets into the ceiling
3.- Hang up the pendulums into these brackets.
4.- Hang up the strips/panel with the angle brackets
panel into the edge of the panel and connect the
pendulums into these.
2.- Screw up the brackets for the chains into the ceiling.
2.- Screw up the strips/panel against the concrete.
Low edge-false ceiling
3.- Hang up the strips/panel with the angle brackets
panel into the edge of the panel.
4.- Adjust the length of the chains as you see of the
drawing.
Mounting in chains
1.- Measure and drill into the ceiling for the strips/panels
brackets. 4 pieces for lengths up to 4,0 m., 6 pieces for
longer units. Observe that the chains must be angled
inwards so the angle brackets will be secured.
20 mm.
1 m. Chain
Aquaztrip H, L
3

Installation instruction
Water connection
Connection alternatives
Connect water with compression coupling or similar. Use the support sleeves. Do not solder!
1
( 1 connected )
The supply and return for this
model are located in the same
end-piece.
This coupling is only avail-
able with one pipe dimension
per panel width.
Width 33: Ø10 mm
Width 60: Ø10 + Ø12 mm
Width 87: Ø10 + Ø15 mm
13
(double circuit )
This model has the supply in
one end-piece and the return
in the other one.
This coupling is only available
with one pipe dimension per
panel width.
Width 33: Ø10 mm
Width 60: Ø12 mm
Width 87: Ø15 mm
1+13
(1 connected + double circuit)
This model is a combination
of 1 connected panel + 1 dou-
ble circuit.
This coupling is available with
only one pipe dimension per
panel width.
Width 33: Ø10 mm
Width 60: Ø12 mm
Width 87: Ø15 mm
13+13
(straight through)
This model has the supply in
one end-piece and the return
in the other one.
This coupling is only available
with one pipe dimension per
panel width.
Width 33: Ø12 mm
Width 60: Ø15 mm
Width 87: Ø22 mm
Aquaztrip H, L
4

Installation instruction
Mounting wire springFalse ceiling adaptation (Aquaztrip H)
It is best if the false ceiling installer mount some head
profiles before the beams will be mounted. This is to
make it easier for the beam installer. If the head profi-
les already are mounted is it very important that you
use a line/wire to have the beams in the right position.
1. Fix the head profiles against the panel with pop ri-
vets or screws.
2. Mount he secondary profiles around the panel. Cut
of the steering pins and fix with pop rivets.
3. One of false ceiling plates and one secondary pro-
file must be cut out, to make room for pipe connec-
tions (only with horizontal connection pipes.)
1.- Attach the spring into the ceiling grid.
2.- Press it over the top of the panel.
3.- Secure that the wire spring is attached between
the ceiling grid and the heating panel.
Insulation of heating panels
The top of the Aquaztrip H- and the Aquaztrip L
panels are insulated with extruded polystyrene
foam and should not be placed in direct sunshine
or underneath other heating- or ignition sources.
Sparks and smoke must be avoided. Keep places dry
and ventilated and take precautions against static
electricity.
The foamed plastic is manufactured without the
addition of CFC or HCFC gas, i.e. Freons.
For full technical data sheet please contact Frico.
Aquaztrip H, L
5

Main office
Frico AB Tel: [phone]
Industrivägen 41
SE-433 61 Sävedalen [email protected]
Sweden www.frico.net
For latest updated information and information
about your local contact: www.frico.net.
2019-09-19,HH
Support
Hjælp
Hjälp
Tuotetuki
Unterstützung
Supporto
UK - Here you can find product updates/mounting
instructions and support telephone number/mail.
www.frico.net
Right to alterations reserved.
DK - Her kan du finde seneste produkt opdateringer/
montagevejledninger samt support tlf. nr/mail.
www.frico.net
Ret til ændringer forbeholdes.
SE - Här kan du alltid hitta senaste
produktuppdateringarna/montageanvisningarna
samt support tel. /e-mail.
www.frico.se
Rätt till ändringar förbehålles.
FI - Täältä löydät uusimmat tuotetiedot ja
asennusohjeet sekä tuotetuen yhteystiedot.
www.frico.net
Oikeus muutoksiin pidätetään.
DE - Hier finden Sie aktuelle Produktinformationen/
Montageanleitungen und Telefonnummer/ E-Mail-
Adressen der Ansprechpartner.
www.frico.net/de
Änderungen vorbehalten.
IT - Qui potete trovare istruzioni di montaggio,
informazioni sul prodotto ed un supporto tecnico
qualificato.
www.frico.net/it
Soggetto a modifica senza obbligo di preavviso.
FR - Vous trouverez les fiches produits ou de montage
actualisées ainsi que les coordonnées du support
téléphonique à l’adresse suivante :
www.frico.fr
Toutes modifications réservées.