Front Runner SAFE010 User manual

SAFE010_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
SAFE010
ENG
1
45 min
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE.
IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH.
YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE.
THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE.
IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES,
YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
Thank you for purchasing a Front Runner Ford Ranger Under Seat Safe.
Before you start, take a moment to familiarize yourself with this Fitting Instruction and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
Ford Ranger
Under Seat Safe

SAFE010_REV_A00 2 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS
4
1
5
5
4
3
4
4
4
4
5
3
4
4
4
4
5
2
TOOLS NEEDED
1 1 X Safe Right Side
2 1 X Safe Left Side
3 10 X M6 Rivnut
4 22 X M6 x 19 x 1SS Flat Washer
5 10 X M6 x 20 Button Head
IN THE BOX
FIGURE 1.1
4MM
Rivnut Tool
9.5MM
GET ORGANIZED
1
Here is what you are looking at for SAFE010

SAFE010_REV_A00 3
FIT AND SECURE
2
2.2
2.3
2.4
2.1
2.1
2.2
2.3
To fit the Under Seat Safe you need to
lift the rear seat of the vehicle.
Loosen and remove the bolts holding the
two plastic trays in place.
On the left side of the vehicle, place
the Safe (Item 2) over the plastic
tray and mark the holes shown in 2.2.
Remove the tray and drill the holes
to 9.5mm. Insert and crimp rivnuts
(Item 3) in all the holes.
Re fit the plastic tray back in place.
Place the Safe (Item 2) over the plastic
tray. Aligning the holes, secure with
fasteners shown in 1.1
TAKE CARE WHEN DRILLING AS THE
FUEL TANK IS SITUATED BELOW THE FLOOR.

SAFE010_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS 4
FIT AND SECURE
2
2.2
2.3
2.4
2.1
2.4
2.5
On the right side of the vehicle, place
the Safe (Item 1) over the plastic
tray and mark the hole shown in 2.4.
Remove the tray and drill the holes
to 9.5mm. Insert and crimp rivnuts
(Item 3) in all the holes.
Re fit the plastic tray back in place.
Place the Safe (Item 1) over the plastic
tray. Aligning the holes, secure with
fasteners shown in 1.1.

SAFE010_REV_A00 © COPYRIGHT 2016 FRONT RUNNER VEHICLE OUTFITTERS 5
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
COMPLETION
3
9
3.1
Congratulations. You did it. Take a step back and admire your work!