Frontgate Carlisle Cast Rect. Dining Table User manual

Assembly Instructions
47610 Carlisle Cast Rect. Dining Table 42" x 86"
ATTENTION:
1. Please read this instruction carefully before assembly.
2. Aluminum is soft metal, over tightening may strip threads or break the part.
3. Do not use power tools.
Assembly steps:
1. Turn table top (A) upside down on a soft clean surface.
2. Attach table legs (D) to long center plates (B) and short center plates（C）with flat washers (F),
lock washers (G) and nuts (H). Don’t tighten.
3. This is the outlook of the assembled table legs with center plates.
4. Loosely attach four legs with center plates to the table top with flat washers (F), lock washers (G)
and bolts (E). Please do not tighten bolts to center bracket until all legs are aligned properly,
and do not over tighten.
5. After all the parts are put in place, tighten all the bolts and nuts completely with outer hexagonal
wrench （J）, but don’t over tighten. Then attach all the nut caps (I). Use feet adjusters to level
the table. This is the outlook of the assembled cast 42”*86” rect. dining table.
Care & Maintenance: Please do not use acid or alkaline washing liquid to clean the product. We recommend
a mild dish soap and warm water for best cleaning results on the metal frames and fabrics.
Frontgate: Please contact one of our Product Specialists for assembly assistance or questions at 1-800-
537-8484 or email:[e-mail]. Specialists are available weekdays 8:00 a.m. to 8:00 p.m .EST or
Saturdays 9:30 a.m. to 6:00 a.m.
Parts Pictures Description Qty Parts Pictures Description Qty
A Table top 1 E Bolt (M8*30) 4
B Long center plate 2 F Flat washer (Φ16*1.0*Φ8.5) 12
C Short center plate 2 G Lock washer (Φ12.5*2.0*Φ8.5) 12
D Leg 4 H Nut (M8) 8
I
Nut cap (M8) 12
J
Outer hexagonal wrench （M8）1

Assembly Instructions
47611B Carlisle Cast Rect. Dining Table Base 42" x 86"
ATTENTION:
1. Please read this instruction carefully before assembly.
2. Aluminum is soft metal, over tightening may strip threads or break the part.
3. Do not use power tools.
Assembly steps:
1. Attach table legs (B) to center plates (A) with flat washers (C), and lock washers (D) and nuts (F).
Don’t tighten.
2. After all the parts are put in place, tighten all the nuts completely with outer hexagonal wrench
（I）, but don’t over tighten. Then attach all the nut caps (G). Use feet adjusters to level the
table. This is the outlook of the assembled cast rect. dining table base.
Care & Maintenance: Please do not use acid or alkaline washing liquid to clean the product. We recommend
a mild dish soap and warm water for best cleaning results on the metal frames and fabrics.
Frontgate: Please contact one of our Product Specialists for assembly assistance or questions at 1-800-
537-8484 or email:[e-mail]. Specialists are available weekdays 8:00 a.m. to 8:00 p.m .EST or
Saturdays 9:30 a.m. to 6:00 a.m.
Parts Pictures Description Qty Parts Pictures Description Qty
A Long center
plate 2 D
Flat washer
(Φ16*1.0*Φ8.5) 8
B
Short center
plate 2 E
Lock washer
(Φ12.5*2.0*Φ8.5) 8
C Leg 4 F Nut (M8) 8
G Nut cap (M8) 8
I
Outer hexagonal
wrench （M8）1