FS S3900 Series User manual

S3900 SERIES MANAGED L2+ GIGABIT
SWITCHES
MANAGED-L2+-GIGABIT-SWITCH DER S3900-SERIE
SWITCHS MANAGEABLES L2+ GIGABIT DE LA SÉRIE S3900
Quick Start Guide V1.0
Quick-Start Anleitung
Guide de Démarrage Rapide

Introduction
Thank you for choosing S3900 Series Stackable Managed Switches. This guide is designed to familiarize
you with the layout of the switch and describes how to deploy the switch in your network.
Accessories
S3900-24F4S-R
S3900-48T6S-R
S3900-24T4S-R
Power Cord x 2
S3900-24T4S-R
Rubber Pad x 4 M4 Screw x 6
Grounding Cable x 1
Console Cable x 1 Mounting Bracket x 2
1
EN

NOTE: S3900 series switches have dust plugs delivered with them. Keep the dust plugs
properly and use them to protect idle optical ports.
S3900-24F4S-R
Power Cord x 2
Rubber Pad x 4 M4 Screw x 8
Grounding Cable x 1
Console Cable x 1 Mounting Bracket x 2
S3900-48T6S-R
Power Cord x 2
Rubber Pad x 4 M4 Screw x 8
Grounding Cable x 1
Console Cable x 1 Mounting Bracket x 2
2
EN

Hardware Overview
Front Panel Ports
S3900-24T4S-R
S3900-24F4S-R
S3900-48T6S-R
CONSOLE SFP+
RJ45
CONSOLE
CONSOLE
SFP
COMBO
RJ45
SFP+
SFP+
Ports Description
10/100/1000BASE-T ports for Ethernet connection
SFP ports for 1G connection
SFP+ ports for 1/10G connection
RJ45
SFP
SFP+
CONSOLE
COMBO
An RJ45 console port for serial management
One RJ45 port and one SFP slot, with one port active at a time
3
EN

Front Panel LEDS
S3900-24T4S-R
SYS Link/Act
PWR
S3900-48T6S-R
RJ45
SFP+
SYS
PWR
S3900-24F4S-R
SYS Link/Act
PWR
Switch is powered on.
System is working properly.
System is started normally.
System is not working properly.
Data is being transmitted or received.
no signal transmission.
Data is being transmitted or received.
No device is connected to the corresponding port.
LEDs DescriptionStatus
PWR Green
SYS
Green
Blinking Green
O
Link/Act
Green
O
RJ45/SFP+
Green
O
4
EN

Back Panels
Only professionals are allowed to install or replace the switch.
Before you begin the installation, make sure that you have the following:
Installation Requirements
Screwdriver
Static-proof wristband
Ethernet cable
Other Ethernet terminal devices
Control terminal
Power switch ON means the power is switched on, while OFF means the power is cut o.
Button Description
S3900-24T4S-R
Dual Power Supplies
S3900-24F4S-R / S3900-48T6S-R
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Grounding Point
Power Switch
Dual Power Supplies
Grounding Point
Power Switch
5
EN

Site Environment:
Do not operate it in an area that exceeds an ambient temperature of 50°C.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
Ensure rack and working platforms are well earthed.
The installation site must be well ventilated. Ensure that there is adequate air ow around the
switch.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
Desk Mounting
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
Mounting the Switch
NOTE: Do not put things weighing 4.5 kg or over 4.5 kg on the top of the switch.
6
EN

Rack Mounting
1. Secure the mounting brackets to the two sides of the switch with M4 screws.
2. Attach the switch to the rack using M6 screws and cage nuts.
ON
OFF
7
EN

ON
OFF
ON
OFF
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the switch back panel with the washers and
screws.
Grounding the Switch
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.
8
EN

ON
OFF
Connecting the Power
WARNING: Do not install power cable while the power is on.
Connecting the RJ45 Ports
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
1. Connect an Ethernet cable to the RJ45 port of a computer, printer, network storage, or other
network devices.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
9
EN