FS MANAGED L2 User manual

V2.0
COMMUTATEUR DE ROUTAGE L2/L3 GÉRÉ
MANAGED L2/L3-ROUTING-SWITCHES
MANAGED L2/L3 ROUTING SWITCHES
Quick Start Guide
Quick-Start Anleitung
Guide de Démarrage Rapide
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
10/100/1000BASE-T
S5800-48T4S
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 910 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
1G
S5800-48F4SR

1
EN
Introduction
Thank you for choosing S5800 Series switches. This guide is designed to familiarize you with the
layout of the switches and describe how to deploy the switches in your network.
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
10/100/1000BASE-T
S5800-48T4S
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
1G
S5800-48F4SR
S5800-48T4S
S5800-48F4SR
Power Cord x2
Grounding Cable x1 Rubber Pad x4 M4 Screw x10
Mounting Bracket x2
Console Cable x1 Network Cable x1
Accessories

2
EN
Hardware Overview
Front Panel Ports
S5800-48F4SR
S5800-48T4S
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
1G
S5800-48F4SR
SFP SFP+CON
USBETH
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
10/100/1000 BASE-T
S5800-48T4S
RJ45 SFP+CON
USBETH
Ports Description
RJ45
SFP
SFP+
CON
10/100/1000BASE-T ports for Ethernet connection
Hot-swappable SFP ports for 1G connection
Hot-swappable SFP+ ports for 1/10G connection
An RJ45 console port for serial management
ETH
USB
An RJ-45 Ethernet management port
A USB management port for software and configuration backup
and offline software upgrade

3
EN
Front Panel LEDs
S5800-48F4SR
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
1G
S5800-48F4SR
SFP SFP+
S5800-48T4S
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
10/100/1000 BASE-T
S5800-48T4S
RJ45 SFP+
ID
SYS
ID indication function enable.Blue
Green
Off
Off
Amber
ID indication function disable.
The system is normally running.
The system occurs alarm or error.
No power or no system runs or system runs abnormally.
SFP+
ETH
RJ45/SFP
Green
Blinking Green
Green
Blinking Green
Blinking Green
Off
Off
Off
Amber
Blinking Amber
Blinking Amber
Green
Amber
Port is linked.
Port is receiving or transmitting packets.
Port is not linked.
1G port is linked.
1G packets are receiving or transmitting.
10/100M port is linked.
10/100M packets are receiving or transmitting.
Port is not linked.
10G port is linked.
10G packets are receiving or transmitting.
1G port is linked.
1G packets are receiving or transmitting.
Port is not linked.
LEDs Status Description
ID SYS
ETH
ETH
ID SYS

4
EN
Back Panel
Site Environment:
Installation Requirements
Grounding Point
3 Fixed Fans 2 Hot-swappable Power Supplies
Do not operate it in an area that exceeds an ambient temperature of 45ºC.
The installation site must be well ventilated. Ensure that there is adequate air flow around the
switch.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
Ensure rack and working platforms are well earthed.
Before you begin the installation, make sure that you have the following:
Phillips screwdriver.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ45 Ethernet cables for connecting the network devices.
S5800-48F4SR/S5800-48T4S

5
EN
Mounting the Switch
Desk Mounting
Rack Mounting
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
1G
S5800-48F4SR
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
1. Secure the mounting brackets to the two sides of the switch with eight M4 screws.
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G

6
EN
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the switch back panel with the washer and
screws.
2. Attach the switch to the rack using four M6 screws and cage nuts.
38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
Grounding the Switch
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.

7
EN
CAUTION: Laser beams will cause eye damage. Do not look into bores of optical modules
or optical fibers without eye protection.
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
1. Plug a compatible SFP/SFP+ transceiver into the SFP/SFP+ port.
2. Connect a fiber optic cable to the fiber transceiver. Then connect the other end of the cable to
another fiber device.
Connecting the Power
Connecting the SFP/SFP+ Ports
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
10G
1G

8
EN
Connecting the Management Ports
1. Insert the RJ45 connector of the console cable into the RJ45 console port on the front of the switch.
2. Connect the other end of the console cable to the RS-232 serial port on the computer.
1. Connect one end of a standard RJ45 Ethernet cable to a computer.
2. Connect the other end of the cable to the ETH port on the front of the switch.
Connecting the Console Port
Connecting the ETH Port
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10
S5800-48F4SR
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22
S5800-48F4SR

9
EN
Configuring the Switch
Insert the Universal Serial Bus (USB) flash disk to the USB port for software and configuration backup
and offline software upgrade.
Step1: Connect the computer to the Management port of the switch using the network cable.
Step 2: Set the IP address of the computer to 192.168.1.x. ("x" is any number from 2 to 254.). Set the
subnet mask of the computer to 255.255.255.0.
Connecting the USB Port
Configuring the Switch Using the Web-based Interface
CON
ETH
ID SYS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
S5800-48F4SR
USB
?x
OK Cancel
General
IP address:
Subnet mask:
Default gateway:
You can get IP settings assigned automatically if your network
supports this capability. Otherwise, you need to ask your network
administrator for the appropriate IP settings.
Internet Protocol Version 4(TCP/IPv4) Properties
Use the following IP address:
Obtain an IP address automatically
Preferred DNS server:
Alternate DNS server:
Validate settings upon exit Advanced...
. . . 21168192
0255
255255
. . .
. . .
. . .
. . .
Obtain DNS server address automatically
Use the following DNS server addresses: