FS S5800-48MBQ User manual

ID MGMT SYS
CON
ETH
S5800-48MBQ
21
43
65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251 5353
40G 40GEBreakout
1 2 3 4
V1.0
S5800-48MBQ
MANAGED L3 MULTIGIGABIT SWITCH
MANAGED L3 MULTI-GIGABIT SWITCH
SWITCH MULTI-GIGABIT GÉRÉ L3
Quick Start Guide
Quick-Start Anleitung
Guide de Démarrage Rapide

ID MGMT SYS
CON
ETH
S5800-48MBQ
21
43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251 5353
40G 40GEBreakout 1 2 3 4
1
EN
Introduction
Accessories
Grounding Cable x1
Power Cord x2
Rubber Pad x4 M4 Screw x12
Console Cable x1
Thank you for choosing S5800-48MBQ switch. This guide is designed to familiarize you with the layout
of the switch and describes how to deploy the switch in your network.
Cat5e Cable x1
Mounting Bracket x2
S5800-48MBQ

2
EN
Hardware Overview
Front Panel Ports
Ports Description
CON
ETH
RJ45
QSFP+
An RJ45 console port for serial management
An Ethernet management port
100/1000/2500BASE-T ports for Ethernet connection
QSFP+ ports for 40G transceivers
SFP28 SFP28 ports for 10G/25G transceivers
RJ45ETH
CON
QSFP+ SFP28
Front Panel LEDs
O
Blue
Amber
O
Green
LEDs Status Description
ID indication function enable.
ID
SYS
ETH
ID indication function disable.
System is running normally.
System occurs alarm or error.
No power or no system runs or runs abnormally.
Port is receiving or transmitting packets.
Port is linked.
Green
Blinking Green
O Port is not linked.
ID MGMT SYS
CON
ETH
S5800-48MBQ
21
43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251 5353
40G 40GE Breakout 1 2 3 4
ID MGMT SYS
CON
ETH
S5800-48MBQ
21
43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251 5353
40G 40GE Breakout 1 2 3 4
ID
SYS RJ45 QSFP+ SFP28
MGMT

3
ENEN
Back Panel
4 Hot-swappable Fans
Blinking Green
Green
Blinking Amber
O
Green
LEDs Status Description
Port is linked at 2.5G.
RJ45
QSFP+
SFP28
Packets are receiving or transmitting at 2.5G.
Port is linked at 100M/1000M.
Packets are receiving or transmitting at 100M/1000M.
Port is not linked.
Packets are receiving or transmitting at 40G.
Port is linked at 40G.
Amber
Blinking Green
Amber
Blinking Amber
O
Green
Port is linked at 10G.
Packets are receiving or transmitting at 10G.
Port is not linked.
Port is linked at 25G.
Blinking Green Packets are receiving or transmitting at 25G.
Amber Port is linked at 10G.
Blinking Amber Packets are receiving or transmitting at 10G.
O Port is not linked.
2 Hot-swappable Power Supplies
Gounding Point

4
EN
Installation Requirements
Phillips screwdriver.
Before you begin the installation, make sure that you have the following:
Site Environment:
M6 Screws.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ-45 Ethernet cables, ber optical cables and console cable for connecting
the network devices.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
Ensure rack and working platforms are well earthed.
Do not operate it in an area that exceeds an ambient temperature of 45°C.
The installation site must be well ventilated. Ensure that there is adequate air ow around the
switch.
Be sure that the switch is level and stable to avoid any hazardous conditions.
ID MGMT SYS
CON
ETH
S5800-48MBQ
21
43
65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 33

5
EN
Rack Mounting
1. Secure the mounting brackets to the two sides of the switch with six M4 screws.
Mounting the switch
Desk Mounting
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
36 3837 4039 4241 4443 4645 4847 5049 5251 5353
40G 40GE Breakout
1 2 3 4
ID MGMT SYS
CON
ETH
S5800-48MBQ
21
43
65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 31

6
EN
Grounding the Switch
CAUTION: The earth connection must not be removed unless all supply connections have
been disconnected.
2. Attach the switch to the rack using four M6 screws and cage nuts.
1. Connect one end of the grounding cable to a proper earth ground, such as the rack in which the
switch is mounted.
2. Secure the grounding lug to the grounding point on the switch back panel with the washer
and screws.
34 3635 3837 4039 4241 4443 4645 4847 5049 5251 5353
40G 40GE Breakout
1 2 3 4
ID MGMT SYS
CON
ETH
S5800-48MBQ
21
43
65 87 109 1211 1413 1615 1817 2019 21

7
Connecting the Power
1. Plug the AC power cord into the power port on the back of the switch.
2. Connect the other end of the power cord to an AC power source.
Connecting the RJ45 Ports
1. Connect an Ethernet cable to the RJ45 port of a computer, printer, network storage, or other
network devices.
2. Connect the other end of the Ethernet cable to the RJ45 port of the switch.
WARNING: Do not install power cable while the power is on.
EN
2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251 5353
40G 40GE Breakout
1 2 3 4
ID MGMT SYS
CON
ETH
S5800-48MBQ
21
43
65 87 109 1211 1413 1615 1817 2019 21

8
1. Plug the compatible QSFP+ transceiver into the QSFP+ port.
2. Connect a ber optic cable to the ber transceiver, then connect the other end of the cable to
another ber device.
3. Or directly connect DAC/AOC cable to the QSFP+ port.
Connecting the QSFP+ Ports
EN
2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251 5353
40G 40GE Breakout
1 2 3 4
CAUTION: Laser beams will cause eye damage. Do not look into bores of optical modules
or optical bers without eye protection.

9
Connecting the SFP28 Ports
1. Plug the compatible SFP28 transceiver into the SFP28 port.
2. Connect a ber optic cable to the ber transceiver, then connect the other end of the cable to
another ber device.
3. Or directly connect DAC/AOC cable to the QSFP28 port.
EN
2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251 5353
40G 40GE Breakout
1 2 3 4
CAUTION: Laser beams will cause eye damage. Do not look into bores of optical modules
or optical bers without eye protection.