FS S3910 Series User manual

RESET
Green=1000M On=LinkYellow=10/100M Flashing=ACT
CONSOLE
STATUS
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423
25 26 27 28
SFP
S3910-24TF
RESET
Green=1000M On=Link
Yellow=10/100M Flashing=ACT
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423
25 26 27 28
SFP+
S3910-24TS
RESET
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 8
710
91211 1413 16
15 1817 2019 22212423 2625 2827 3029 3231 3433 3635 38
37 4039 4241 4443 4645 4847 5049 5251
SFP+
Green=1000M Yellow=10/100M On=Link Flashing=ACT
S3910-48TS
MANAGED L2+ GIGABIT SWITCHES
MANAGED L2+ GIGABIT SWITCHES
SWITCHS MANAGEABLES L2+ GIGABIT
Quick Start Guide V2.0
Quick-Start Anleitung
Guide de Démarrage Rapide
S3910 Series Switches

Introduction
Thank you for choosing S3910 Series Stackable Managed Switches. This guide is designed to
familiarize you with the layout of the switch and describes how to deploy the switch in your network.
Accessories
RESET
Green=1000M On=LinkYellow=10/100M Flashing=ACT
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423
25 26 27 28
SFP+
S3910-24TS
S3910-24TS
S3910-48TS
S3910-24TF
Power Cord x1
S3910-24TF
Rubber Pad x4
M4 Screw x6Mounting Bracket x2
Grounding Cable x1
Cable Clamps x1
RESET
Green=1000M On=LinkYellow=10/100M Flashing=ACT
CONSOLE
STATUS
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423
25 26 27 28
SFP
S3910-24TF
RESET
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251
SFP+
Green=1000M Yellow=10/100M On=Link Flashing=ACT S3910-48TS
1
EN

NOTE: S3910 series switches have dust plugs delivered with them. Keep the dust plugs
properly and use them to protect idle optical ports.
Power Cord x2 Rubber Pad x4
M4 Screw x8
Grounding Cable x1
S3910-24TS/S3910-48TS
Hardware Overview
Front Panel Ports
RESET
Green=1000M On=LinkYellow=10/100M Flashing=ACT
CONSOLE
STATUS
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423
25 26 27 28
SFP
S3910-24TF
S3910-24TF
Ports Description
RJ45
CONSOLE
SFP
10/100/1000BASE-T ports for Ethernet connection
SFP ports for 1G connection
An RJ45 console port for serial management
CONSOLE SFPRJ45
Mounting Bracket x2
2
EN

RESET
Green=1000M On=LinkYellow=10/100M Flashing=ACT
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423
25 26 27 28
SFP+
S3910-24TS
RESET
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251
SFP+
Green=1000M Yellow=10/100M On=Link Flashing=ACT
S3910-48TS
CONSOLE
S3910-24TS
SFP+RJ45
CONSOLE SFP+RJ45
S3910-48TS
Ports Description
RJ45
CONSOLE
SFP+
10/100/1000BASE-T ports for Ethernet connection
SFP+ ports for 1/10G connection
An RJ45 console port for serial management
RESET
Green=1000M On=LinkYellow=10/100M Flashing=ACT
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423
25 26 27 28
SFP+
S3910-24TS
Front Panel Button
RESET
S3910-24TF/S3910-24TS/S3910-48TS
Button Description
RESET Restart: Press and hold the RESET button for more than five seconds, and
then wait for ten seconds.
3
EN

Back Panels
S3910-24TS/S3910-48TS
PWR1 PWR2
Dual Power Supplies Grounding Point
Front Panel LEDs
RESET
Green=1000M On=LinkYellow=10/100M Flashing=ACT
CONSOLE
STATUS
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423
25 26 27 28
SFP
S3910-24TF
S3910-24TF
SFP
RJ45
STATUS
S3910-24TF
Power Supply
Cable Clamps Holes
Grounding Point
STATUS
Off Switch is not receiving power.
Blinking Green System is being initialized.
Solid Green
Solid Red
Switch is operational.
1. Severe temperature warning:
The temperature severely exceeds the temperature limit, so
the system is going to restart.
2. The switch is faulty.
LEDs DescriptionStatus
4
EN

RESET
Green=1000M On=LinkYellow=10/100M Flashing=ACT
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423
25 26 27 28
SFP+
S3910-24TS
S3910-24TS
SFP+
RJ45
STATUS
PWR1 ID
PWR2
RESET
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251
SFP+
Green=1000M Yellow=10/100M On=Link Flashing=ACT
S3910-48TS
S3910-48TS
SFP+
RJ45
PWR1 ID
STATUS
PWR2
LEDs DescriptionStatus
RJ45
SFP
Off The port is not connected.
Solid Green
Solid Yellow
The port is connected at 1000 Mbps.
The port is connected at 10/100 Mbps.
Blinking Green The port is receiving or transmitting traffic at 1000 Mbps.
Blinking Green The port is receiving or transmitting traffic.
Blinking Yellow The port is receiving or transmitting traffic at 10/100 Mbps.
Off The port is not connected.
Solid Green The port is connected.
5
EN

LEDs DescriptionStatus
STATUS
Off
Blinking Green
Solid Yellow
Solid Red
Solid Green
System is being initialized.
Switch is operational.
Switch is not receiving power.
1. Severe temperature warning:
The temperature severely exceeds the temperature limit, so
the system is going to restart.
2. The switch is faulty.
Moderate temperature warning:
Check the working environment of the switch immediately.
PWR1/PWR2
ID
RJ45
Off
Solid Green
Solid Red
A power supply is connected and able to work.
A redundant power supply fails or no AC cable is connected.
No power supply module is connected.
Off
Solid Blue
Off
Locating is enabled. Operation and maintenance staff turn
on and off the LED remotely.
The port is not connected.
Solid Green The port is connected at 1000 Mbps.
Blinking Green The port is receiving or transmitting traffic at 1000 Mbps.
Solid Yellow The port is connected at 10/100 Mbps.
Blinking Yellow The port is receiving or transmitting traffic at 10/100 Mbps.
Locating is disabled.
SFP+
Off The port is not connected.
Solid Green The port is connected.
Blinking Green The port is receiving or transmitting traffic.
6
EN

RESET
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 2625 27
Green=1000M Yellow=10/100M On=Link Flashing=ACT
Before you begin the installation, make sure that you have the followings:
Site Environment:
Do not operate it in an area that exceeds an ambient temperature of 50°C.
Installation Requirements
Phillips screwdriver.
Standard-sized, 19" wide rack with a minimum of 1U height available.
Category 5e or higher RJ-45 Ethernet cables, fiber optical cables and console cable for connecting
network devices.
Do not install the equipment in a dusty environment.
The installation site must be free from leaking or dripping water, heavy dew, and humidity.
The installation site must be well ventilated. Ensure that there is adequate airflow around the
switch.
The switch should be installed at least 1U (44.45mm) away from devices to its sides.
Be sure that the switch is level and stable to avoid any hazardous conditions.
Ensure rack and working platforms are well earthed.
7
EN

RESET
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 1817 2019 2221 2423 25
Green=1000M Yellow=10/100M On=Link Flashing=ACT
26 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251
SFP+
S3910-48TS
RESET
CONSOLE
STATUS PWR1 PWR2 ID
21 43 65 87 109 1211 1413 1615 17
Green=1000M Yellow=10/100M On=Link Flashing=ACT
Desk Mounting
1. Attach four rubber pads to the bottom.
2. Place the chassis on a desk.
Mounting the Switch
Rack Mounting
1. Secure the mounting brackets to the two sides of the switch with the supplied M4 screws.
8
EN

S3910-48TS
2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251
SFP+
S3910-48TS
18 2019 2221 2423 2625 2827 3029 3231 3433 3635 3837 4039 4241 4443 4645 4847 5049 5251
SFP+
S3910-48TS
2. Attach the switch to the rack using four M6 screws and cage nuts.
1. Attach the mounting brackets to the switch with the supplied M4 screws.
Wall Mounting
9
EN