FUFU & GAGA KF330036 User manual

Version:05/26/2022 1/14
Sideboard

please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!
2/14

When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Please prepare the following tools
3/14
A x 16 B x 16
15 x 9 mm
C x 8 D x 12
F x 6 K x 2
M x 4
J x 2
4 x 35 mm
7 x 35 mm
4 x 45 mm
N x 4
E x 20
L x 8
H x 2
3x 14 mm
6 x 30 mm 3 x 12 mm
12x 1
mm
16x 1
mm
R x 16
4 x 25 mm
6 x 50 mm
G x 8
P x 2 Q x 2
4 x 14 mm

4/14
1
2
3
45
6
6
7
8
8
8
8
7
9
9
9
9
10
11
12
13
14
15
X2

5/14
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Please prepare the following tools
x 1
1x 1 2x 1 3x 1 4x 1 5
x 2
6x 2 7x 4 8x 4 9x 2 10
x 2
11 x 2 12 x 2 13 x 2 14 x 1 15

1
7 x 35 mm
A x 4
3 x 12 mm
2
E x 12
6/14
1
2
A
1
A
A
A
A
E
E
E
E
E
E
E
E
H
HJ
J
3 4
H x 2 J x 2
1
E
EE
E
E
H
A
A
AA
7 x 35 mm
A x 4
Fix quickfit screw A to panel 1 as shown.
Please note don't use an electric screwdriver
or use force to rotate, may cause crack.
Fix quickfit screw A to panel 3&4 as shown.
Fix runner H&J to panel 3&4 using screw E as shown.
Please pay attention to the holes where the accessories are inserted.

3
15 x 9 mm
B x 4
4
7/14
C
B
180°
BB
B
B
C
C
C
C
1
3
4
1
4
6 x 30mm
C x 4
15
15
180°
B
B
B
B
B
B
Connect panel 15 to panel 3&4,turn cam locks
B clockwise to tighten as shown.
First insert half wooden dowels C into panel 3&4,
then attach panel 1 to panel 3&4,turn cam locks
B clockwise to tighten as shown.
15 x 9 mm
B x 4

5
8/13
6
5
2
C
C
C
C
D
D
D
D
D
C
6 x 30mm
C x 4
4 x 35mm
D x 4
6
7
8
6
7
R
RR
R
R
8
4x 25 mm
R x 16
Slide panel 5 into available slot in panel 3&4,
insert half wooden dowels C into panel 3&4,and
attach panel 2 using screw D as shown.
Please note don't use an electric screwdriver or
use force to rotate, may cause crack.
Connect panel 6 and 7 to part 8, and use screw R to fix as shown.

7
6 x 50 mm
G x 8 L x 8
9/14
816x 1
mm
L
G
L
G
9
9
9
99
8
K
12x 1
mm
16x 1
mm
L
4x 45 mm
F x 6
2
F
FF
FF
F
F
Connect 2 assembled components using screw F as shown.
Fix legs 9 using bolt L&G as shown.

9
10/14
7 x 35 mm
A x 8
A
A
A
A
B
B
B
B
x2
10
10
11
12
B x 8
15 x 9 mm
x2
D
D
D
D
P
Q
×2
10
11
11
12
12
13
10
D x 8P x 2
4 x 35 mm
Q x 2
4 x 14 mm
10
A
D
14
12x 1
mm
K x 2
K
Fix quickfit screw A to panel 10 as shown.
Attach panel 11 and 12 to panel 10, turn
cam locks B clockwise to tighten as shown.
Slide panel 14 into available slot in panel 11&12,
then attach panel 13 using screw D.
Fix handle K to panel 10 as shown.