FUFU & GAGA KF020309-01 User manual

TV Cabinet
or
Plan (1)
Plan (2)
Version:09/23/2022

2/28
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!

Ax16(+1) Bx16(+1) Cx24(+1) Dx10(+1)
Ø6x35mm Ø15x10mm
Ex10(+1) Fx2
Ø6x30mm
Gx4
Ø4x35mm
Ø3x16mm
Ø3x12mm
Hx20(+1)
Ø3.5x10mm
Jx4 Kx24(+1) Lx4 Mx2
Nx8 Px12
3/28
Ø3x16mm
Qx12 Rx4
Ø4x35mm Ø3.5x10mm
Please prepare the following tools
When installing, please carefully confirm whether
each screwcorresponds to the manual, accessories
with similar shapes can be distinguished by size

Sx4
Wx2
Tx6 Ux2 Vx2
Yx4
4/28
Ø3x12mm
Ø4x14mm
Ø6x30mm

1
2
3
4
5
6
7
6
11
11
12
15
15
8
14
14
13
13
14
14
16
17
9
9
10
9
9
10
5/28

Fx2
1
FF
F3
F1
F2
F2 F3 F1
Ex3
F1
2
Ex6
Ø3.5x10mm
F1x2
F1
E
E
E
x2
2
55
6/28
Separat part(F) into 3 parts as shown.
Fix part(F1) to No.2 and No.5 with
screw(E) as shown.

Ax4
Ø6x35mm
2
3
Cx2Bx2
Ø15x10mm
A
Ø6x30mm
I II III
3
4
B
B
A
A
AA
C
C
2
6
2
B
C
180°
6
2
7/28
Insert quickfit screw(A) into No.2 and
No.3 plate with a screwdriver
as shown.
Connect No.6 with No.2 plate using wooden
dowel(C) and turn cam lock(B)
clockwise to tighten as shown.

A
A
B
C
A
AA
Cx2Bx2
Ø15x10mm Ø6x30mm
5
I II III
C
B
C
B
6
2
3
6
Ax4
Ø6x35mm
6
5
4
4
3
8/28
180°
Connect No.3 plate with No.6
using wooden dowel(C) and
turn cam lock(B) clockwise to
tighten as shown.
Insert quickfit screw(A) into No.4 and
No.5 plate with a screwdriver as shown.

Cx2Bx2
Ø15x10mm Ø6x30mm
I II III
I II III
7
8
Cx2Bx2
Ø15x10mm Ø6x30mm
C
C
B
B
B
C
C
C
B
B
C
B
6
5
6
5
4
6
5
6
4
9/28
180°
180°
Connect No.6 with No.5
plate using wooden
dowel(C) and turn cam
lock(B) clockwise to
tighten as shown.
Connect No.4 with No.6
using wooden dowel(C)
and turn cam lock(B)
clockwise to tighten as
shown.

Cx8
Ø6x30mm
9
C
C
C
C
C
C
C
C
C
Ax8
Ø6x35mm
A
A
A
A
A
A
A
A
A
10
2
6
3
4
4
6
5
1
1
10/28
Insert wooden tenon(C) into No.2, No.3, No.4
and No.5 plate as shown.
Insert quickfit screw(A) into corresponding
holes in No.1 plate with a screwdriver as
shown.