FUFU & GAGA KF200139 User manual

1/12
Shoe cabinet
Version:07/19/2022

2/12
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!

A x 16 B x 24 C x 4 D x 2
E x 4 F1 x 4 F2 x 4 F3 x 4
G x 16 H x 4I x 4 J x 22
L x 2 R x 2
3/12
3.5 x 14 mm4 x 40 mm 4 x 10 mm
4 x 16 mm
2.5 x 14 mm6 x 30 mm
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Please prepare the following tools
12 mm

4/12
1
2
3
4
5
5
9
6
8
8
7x2

F1 x 4
1
H x 4
F2 x 4
F1
3
F2
F1
F2
F1
F2
F1
F2
F1
F2
2
1
H
H
H
H
H
6 x 30 mm
Hammer F1 & F2 slightly into the holes on panel 2 &3,
Note do not tilt to avoid damage.
Insert the wooden tenon (H) into plate 1, as shown.
5/12

2
4 x 40 mm
Attach panel 1,4 and 5 to panel 3
using screw A as shown.
6/12
13
5
5
4A
A
A
A
A
A
A
A
G
G
G
G
G
3
G x 8
12 mm
A x 8
G
A
A

3
1
2
5
5
4
2
A
A
A
A
A
A
A
A
G
G
G
G
G
4 x 40 mm
3
Attach panel 1,4 and 5 to panel 2
using screw A as shown.
7/12
G x 8
12 mm
A x 8
G
A
A
A

J x 22
4
90°
J
J
J
J
J
J
J
J
J
9
x22
I
I
I
I
I
180°
2.5 x 14 mm
I x 4
Fix panel 9to the back of assembled unit using screw J to
pre-drilled holes as shown.
Fix part I to the bottom.
8/12
9

5
x2
B x 4
6
x2
9/12
R
L
E
E
D
B
B
B
R
L
B
B
R
B x 16
3.5 x 14 mm
D x 2 E x 4 L x 2 R x 2
4 x 16 mm
B C
3.5 x 14 mm 4 x 10 mm
Fix plastic part L&R to panel 8, use screw B to tighten.
Attach this part to panel 6 using screw B to corresponding holes as shown.
L
R
B
B
B
B
B
B
B
E
D
Attach panel 7 to the assembled part
using screw B slightly to tighten, as shown.
B
3.5 x 14 mm
8
8
6
6
6
7
7

F3 x 4 C x 4
7
Fix the plastic part L&R to panel 2&3 by
using F3 slightly. Then screw C to tighten.
10/12
2
L
3
F3 C
R
F3
C
L
R
6
6
F3
C
F3 C
F3
C
CB
4 x 10 mm
4 x 10 mm 3.5 x 14 mm