FUFU & GAGA Chest User manual

Chest
Version:07/01/2022 1/13
FUFU&GAGA

FUFU&GAGA
2/13
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!

When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
Please prepare the following tools
3/13
3 x 12 mm 15 x 9 mm
C x 24
6 x 35 mm
4 x 35 mm 6 x 30 mm
6 x 30 mm
3.5 x 14 mm
8 x 30 mm
D x 29 E x 29 F x 10 CR x 3
CL x 3 DR x 3 DL x 3 G x22
J x 6 L x 1 M x 1
P x 1
4 x 14 mm
H x 6
K x 3 N x 1

4/13
5
6
6
2
1
4
7
3
13
x3
9
14
11
12
10
8
8
15

1
CR x 3 CL x 3
1
3 x 12 mm 6 x 35 mm
C x 12
5/13
D x 10
C
C
C
CR
C
CL
C
CR
CR
CR
C
C
C
C
CL
CL
CL
D
D
D
D
C
C
C
C
C
3
2D
Fix runner CL&CR to panel 2 and 3 as shown.
Insert quickfit screw D into panel 2 and 3.
Please pay attention to the holes where the
accessories are inserted and don't use an
electric screwdriver.
D
D
D
D
D
D

2
E x 10
6/13
15 x 9 mm
F x 2
6 x 30 mm
IIIIII
EE
E
E
E
EE
EE
E
F
F
4
5
15
3
2
15
5
4
E
E
Attach panel 4, 5 and 15 to panel 3
with wooden dowel F, then turn cam
locks E clockwise to tighten as shown.
Attach panel 2 with wooden dowel F
and turn cam lock E clockwise to
tighten as shown.

3
F x 4
7/13
4
D x 4
6 x 35 mm
6 x 30 mm
D
D
D
D
1
D
Insert wooden dowels F to the
corresponding holes in panel 2&3
slightly.
Slide panel 6 to the
available slots
in panel 2&3.
Insert quickfit screw D into panel 1.
Please pay attention to the holes where
the accessories are inserted don't use an
electric screwdriver or use force to rotate,
may cause crack.
2
63
F
F
F
F
F

5
E x 4
8/13
6
F x 4
6 x 30 mm
15 x 9 mm
IIIIII
Flip the assembled component 180°.
Insert wooden dowels F to the
corresponding holes in panel 3&2
slightly.
Slide panel 6 to the available slots in
panel 3&2.
G
2
3
1
1
G
3
6
2
F
15
G
4 x 35 mm
G x 2
1
Cover panel 1 to panel 2 and 3, turn cam
lock E clockwise to tighten as shown.
And panel 1 needs to be attached to
panel 15 with screw G as shown.
Please note don't use an electric
screwdriver or use force to rotate,
may cause crack.

7
G x 4
9/13
4 x 35 mm
8
H x 6 L x 1
6 x 30 mm
Attach panel 7 to panel 2&3 using
screw G. Please note don't use an
electric screwdriver or use force to
rotate, may cause crack.
Fix legs 8 to panel 7 using nail H as shown.
H
L
8
7
G
G
G
G
G

9
10/13
G x 15
4 x 35 mm
10
x3
x3
G
G
G
G
G
13
12
14
10
10
11
Attach panel 10 and 11 to panel 12 using screw G.
Connect panel 13 to panel 12 using screw G, as shown.
Slide panel 14 to available slots in panel 10&11.
G
13
12