FUFU & GAGA LJY-KF210118-02 User manual

1/28
Shoe cabinet

2/28
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!

3/28
Ax15
Ø6x35mm
Bx15
Ø15x10mm
Cx22
Ø6x30mm
Dx12
Ex3 Fx4 Gx6 Hx36
Ix6 Jx28 Kx4 Lx3
Mx2
Ø4x14mm
Ø4x40mm
Ø3.5x14mm
Ø3.5x14mm
Ø4x10mm
E-1
E-2
G-1 G-2 G-3
M-1 M-2
Ø4x14mm
Nx4
N-1 N-2
Ø6x30mm Ø4x40mm
Ox2 Px12
Please prepare the following tools
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size

4/28
Qx1 Rx8 Sx1
1
2
3
4
5
6
7
8
9
10
11
12
13
13
13
14
14
14
14
15
16
16
17
18
18
19
19
19
19
19
19
20
20
20
21

5/28
1Ax6
Ø6x35mm
Tighten Cam Bolt (A) to panel 2 and
panel 4 ,as shown.
2
2
4
A
AA
A
A
A
2
Please hammer the G-1 and
G-2 onto the 2 and 3 boards ,as shown.
2
4
G-1
G-1
4
4
G-2
Gx6
G-1 G-2
G-1
G-1
G-1
G-1
G-2
G-2
G-2
G-2
G-2

6/28
3
Please turn No. 2 board and No. 4
board behind, INSERT SAWDUST
C into No. 5 board, No. 6 board
and No. 7 board respectively,
then Lock with Cam Lock B with
No. 2 board and No. 4 board
respectively,as shown.
4
2
Back
Back
Front
Front
7
6
5
BC
180°
52B
B
B
B
B
C
C
C
C
7
6
52
4
Back
Please note that the
orientation of the
holes in the CAM Lock
is behind the cabinet
Bx6
Ø15x10mm
Cx6
Ø6x30mm
IIIIII

7/28
4
(1)Tighten Cam Bolt (A) to panel 1,as shown.
(2)Please use screw (J) to lock with
Iron Sheet (F) and plate No. 8
respectively,as shown.
1
1
A
AA
A
A
A
A
A
A
8
8
J
J
J
J
J
F
F
F
F
J
J
J
JJ
J
J
J
J
J
J
J
J
JJ
Ax9
Ø6x35mm
Fx4 Jx20
Ø4x14mm

8/28
5Cx8
Insert wooden pins (C) at the
bottom of plate 2 and Plate 4
Plate 7 Use Screws (D) to lock
plate No. 8 with plate No. 2
and Plate No. 3 Plate No. 4
Plate 7,as shown.
3
4
2
5
6
7
8
Back
Back
Back
C
C
C
C
C
C
C
C
DD
D
D
D
D
DD
D
8
4
Ø6x30mm
Dx9
Ø4x40mm

9/28
6Qx1
48
2
6
7
14
14
14
14
8
14
8
15
15
F
Q
5
3
Please turn the number 14 pin to the plate (F) screw lock respectively .
Please rotate number 15 pin to number 8 board.
Please use adjustment pad (Q) to rotate number 15 pin,as shown.

10/28
7Cx8
Wood pins (C) are inserted in the
upper parts of Plate 2 Plate 3
Plate 4 and Plate 5,as shown.
2
4
3
5
8
C
C
C
C
C
C
C
4
C
Ø6x30mm
6
7
15
Q
8
15
14 14