Fujitsu MB89P935 Operator's manual

MB89P935 OTP BOARD
Documentation
Fujitsu Microelectronics America Inc
San Jose CA
Revision: V1.0
Date: 01/18/01
1

Warranty and Disclaimer
To the maximum extent permitted by applicable law, Fujitsu Microelectronics America Inc San Jose
restricts its warranties and its liability for the Product [F2MC-16 LX-series Evaluation Board Hardware
and Software Tools], its performance and any consequential damages, on the use of the Product in
accordance with (i) the terms of the License Agreement and the Sale and Purchase Agreement under
which agreements the Product has been delivered, (ii) the technical descriptions and (iii) all accompanying
written materials.
This product has been created to work in laboratory environment only. In addition, to the maximum extent
permitted by applicable law, Fujitsu Microelectronics America Inc San Jose disclaims all warranties and
liabilities for the performance of the Product and any consequential damages in cases of unauthorized
decompiling and/or reverse engineering and/or disassembling.
1. Fujitsu Microelectronics America Inc San Jose warrants that the Product will performsubstantially
in accordance with the accompanying written materials [this manual] for a period of 90 days form
the date of receipt by the customer. Concerning the hardware components of the Product, Fujitsu
Microelectronics America Inc San Jose warrants that the Product will be free from defects in
material and workmanship under use and service as specified in the accompanying written
materials for a duration of 1 year from the date of receipt by the customer.
2. Should a Product turn out to be defect, Fujitsu Microelectronics America Inc San Jose’s entire
liability and the customer’s exclusive remedy shall be, at Fujitsu Microelectronics America Inc
San Jose ´s sole discretion, either return of the purchase price and the license fee, or replacement
of the Product or parts thereof, if the Product is returned to Fujitsu Microelectronics America Inc
San Jose in original packing and without further defects resulting from the customer’s use or the
transport. However, this warranty is excluded if the defect has resulted from an accident not
attributable to Fujitsu Microelectronics America Inc San Jose, or abuse or misapplication
attributable to the customer or any other third party not relating to Fujitsu Microelectronics
America Inc San Jose.
3. To the maximum extent permitted by applicable law Fujitsu Microelectronics America Inc San
Jose disclaims all other warranties, whether expressed or implied, in particular, but not limited to,
warranties of merchantability and fitness for a particular purpose for which the Product is not
designated.
4. To the maximum extent permitted by applicable law, Fujitsu Microelectronics America Inc San
Jose ´s and its suppliers´ liability is restricted to intention and gross negligence.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES
To the maximum extent permitted by applicable law, in no event shall Fujitsu
Microelectronics America Inc San Jose and its suppliers be liable for any damages
whatsoever (including but without limitation, consequential and/or indirect damages for
personal injury, assets of substantial value, loss of profits, interruption of business
operation, loss of information, or any other monetary or pecuniary loss) arising from the
use of the Product.
Should one of the above stipulations be or become invalid and/or unenforceable, the remaining
stipulations shall stay in full effect.
Date: 22.01.99, V1.0
2

Contents
1. Introduction
2. Hardware Documentation
2.1 Board Features
2.2 Hardware Requirement
2.3 Jumper Setting
2.4 Hardware Set-up
3 Software Documentation
3.1 Software Requirement
3.2 Software installation
3.3 Running the Sample Programs
4 Appendix
Schematic and drawings
3

1. Introduction
The MB89P935A OTP Board is a low cost target board for the Fujitsu MB89930A series.
It can be used as a low cost target system for software development. The board supports
on-board serial programming of OTPROM via Yokogawa programmer or via the RS232
interface. The board has special connector J1 to connect to the standard target probe cable
(AZ210), which is required to connect the Yokogawa programmer to the target board. The
board allows the designer to start the software development before his final target system
is available.
Note: This board can only be used with the OTP chip MB89P935A. It is recommended to
use the different board, the “MB89PV930A Evaluation board”(Contact Fujitsu for this)
for software development using an In Circuit emulator.
2 Hardware Documentation
2.1 Board Features
The MB89P935A OTP board features are:
- OTP socket for better connectivity.
- 5V external DC power supply.
- One RS232 interface.
- Reset push button.
- Yokogawa interface for programming.
- On Board internal +9V power supply.
- Power indication LED for both External +5V and on board internal +9V power supply.
2.2 Hardware Requirements
- MB89P935A OTP board.
- 7 Jumpers.
- Serial cable/Yokogawa Cable.
- External +5V power supply
2.3 Jumper Setting
There are seven jumpers on the board. The setting of these jumpers decides the modes
(Programming mode, Normal mode) of the Microcontroller. Connect the jumpers as
shown in the table1.
Table1: Jumper setting for the OTP Board
Mode J1 J2 J3 J4 J5 J6 J7
Serial Programming
via RS232 cable
1-2 1-2 1-2 1-2 1-2 1-2 2-3
Yokogawa
Programming
1-2 1-2 2-3 2-3 2-3 2-3 1-2
Normal Mode 2-3 2-3 - - - - -
Note: 1-2 (or 2-3) indicates a jumper connection between pin no 1 and 2 of the
corresponding jumper pins .
4

2.4 Hardware Set-up
This section shows how to set up the hardware for the MB89P935A OTP board:
Serial cable
Power supply
+5V, 1amp
PC Host Evaluation Board
with OTP chip
Figure 1 : Hardware Set up of OTP board
3 Software Document
3.1 Software Requirement:
The following components are necessary:
- Fujitsu Micro’s MCU CD-ROM V3.0 or higher
- PC with Windows3.1x or higher.
- Sample application programs for MB89930A series.
- OTP programming utility
3.2 Software Installation
i) Insert the Fujitsu CD-ROM into the CD-ROM drive and install the Softune
Workbench for 8-bit Microcontroller.
ii) Install the OTP programming utility.
iii) Install the sample program for MB89930A series.
3.3 Running the Sample program
i) Make the Hardware set up as shown in figure 1.
ii) Configure the jumpers J1, J2, J3, J4, J5, J6 and J7 as shown in table 1, depending
on the serial cable (RS232 or Yokogawa).
iii) Put the MB89P935A OTP chip on the socket,( be sure the power is switched off
before inserting the device).
iv) Connect an external +5V power supply to the board and power up the board
(Check the green power LED).
v) Compile the sample program and start the OTP programming utility. Select the
COM port and hit the download button.
vi) After programming is done, change the jumper setting to the normal mode.
vii) If you wait for a while (not necessary), your programmed application will start
executing.
5

Cross References:
- MB89930A Series Datasheet.
- MB89930A Series Hardware Manual.
6

Appendix
Schematic: MB89P935 OTP Board
7