Fujitsu F2MC-16LX Series User manual

SS01-44005-1E
SUPPORT SYSTEM
FUJITSU SEMICONDUCTOR
F2MC-16LX
LQFP-48P PROBE CABLE (NQPACK VERSION)
OPERATION MANUAL
MB2132-466

1
PREFACE
Thank you for purchasing the MB2132-466 (LQFP-48P (*1) probe cable <NQPACK version>).
The MB2132-466 probe cable is used to connect an emulator for F2MC (*2)-16LX to a user system.
This manual explains the handling and operation of the MB2132-466 (LQFP-48P probe cable
<NQPACK version>). Read this manual carefully before using the MB2132-466.
*1: The applicable package is the FPT-48P-M05 (lead pitch: 0.5 mm, body size: 7 x 7 mm).
*2: F2MC is the abbreviation of FUJITSU Flexible Microcontroller.
• The contents of this document are subject to change without notice. Customers are advised to consult
with FUJITSU sales representatives before ordering.
• The information and circuit diagrams in this document are presented as examples of semiconductor
device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU
is unable to assume responsibility for infringement of any patent rights or other rights of third parties
arising from the use of this information or circuit diagrams.
• The products described in this document are designed, developed and manufactured as contemplated
for general use, including without limitation, ordinary industrial use, general office use, personal use,
and household use, but are not designed, developed and manufactured as contemplated (1) for use
accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious
effect to the public, and could lead directly to death, personal injury, severe physical damage or other
loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass
transport control, medical life support system, missile launch control in weapon system), or (2) for use
requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages
arising in connection with above-mentioned uses of the products.
• Any semiconductor devices have an inherent chance of failure. You must protect against injury,
damage or loss from such failures by incorporating safety design measures into your facility and
equipment such as redundancy, fire protection, and prevention of over-current levels and other
abnormal operating conditions.
• If any products described in this document represent goods or technologies subject to certain
restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior
authorization by Japanese government will be required for export of those products from Japan.
©2002 FUJITSU LIMITED Printed in Japan

2
1. Checking packed components
Before using the MB2132-466, make sure the following components have been provided.
•
••
• MB2132-466 (LQFP-48P Probe Cable): 1
•
••
• Screws for securing probe header (M2 x 14 mm with washer): 4
•
••
• NQPACK048SD (Compatible socket manufactured by Tokyo Eletech Corporation): 1
•
••
• HQPACK048SD (Socket cover for mounting MCU manufactured by Tokyo Eletech
Corporation): 1
•
••
• Operation manual (Japanese version): 1
•
••
• Operation manual (English version, this manual): 1
2. Handling Precautions
The MB2132-466 (LQFP-48P probe cable <NQPACK version>, hereafter called the probe cable) , is
precision-manufactured to improve dimensional accuracy and to ensure reliable contact. The probe
cable is therefore sensitive to mechanical shock. To ensure correct use of the probe cable in the
proper environment, observe the following points regarding its insertion and removal:
•
••
• To connect the probe cable to a user system, insert the probe header into the NQPACK
mounted on the user system board by aligning the first pin (▲) of the NQPACK with the
first pin of the probe header ( ) as shown in Figure 2-1. Secure the header with four of
the screws. Do not overtighten the screws.
4 screws for securing the probe header
First pin
First pin
Reinforcing board
YQPACK048SD
NQPACK048SD
User system board
Figure 2-1 Probe cable connection

3
•
••
• The probe cable is not very flexible sideways. To avoiding placing extra stress on the
probe cable, consideration must be given to the location of the emulator relative to the
user system, and the emulator's orientation.
•
••
• To remove the probe cable, remove all four screws, and pull out the header vertically.
CAUTION
Caution
Do not forcibly bend the probe cable, and do not cut the probe cable.

4
3. Mounting Mass-produced MCUs
To mount a mass-produced MCU on the user system without connecting an emulator, use the socket
cover (HQPACK048SD) that is supplied with the probe cable.
To mount a mass-produced MCU on the user system, place the mass-produced MCU on the user
system by aligning the first pin (▲) of the NQPACK mounted on the user system with the first pin
(●) of the pass-produced MCU as shown in Figure 3-1. Make sure that the mass-produced MCU is
properly placed on the NQPACK. Then, align the first pin of the NQPACK and HQPACK (one
corner of the HQPACK is clipped) in the correct direction as shown in Figure 3-1, and secure them
with four screws. Do not over tighten these screws.
4 screws for securing HQPACK
(Supplied with HQPACK)
First pin
User system board
HQPACK048SD
Mass-produced MCU
The corner is clipped.
NQPACK048SD
Figure 3-1 Mounting a mass-produced MCU
CAUTION
Caution
Align the first pin on the mass-produced MCU so that its orientation is correct.
Otherwise, the mass-produced MCU or the user system may be damaged.

5
4. Probe Cable Dimensions
240mm
33mm
33mm
13mm
75mm
Figure 4-1 Probe cable dimensions

6

SS01
-
44005
-
1E
FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM
F2MC-16LX
LQFP-48P PROBE CABLE <NQPACK VERSION>
MB2132-466
OPERATION MANUAL
February 2002 the first edition
Published FUJITSU LIMITED Electronic Devices
Edited Technical Information Dept.