Fujitsu MB91460 SERIES User manual

Fujitsu Microelectronics Europe
Application Note
MCU-AN-391005-E-V17
FR FAMILY
EMULATION SYSTEM
MB91460
GETTING STARTED
APPLICATION NOTE

Getting Started
Revision History
MCU-AN-391005-E-V17 - 2 - © Fujitsu Microelectronics Europe GmbH
Revision History
Date Issue
2005-05-18 V1.0; UMa
2005-07-18 V1.1; UMa
2005-07-28 V1.2; UMa
2005-08-16 V1.3; UMa
2005-09-02 V1.4; PHu: specify board in 4.1 Providing a Clock Source; clarify jumper
setting in 5.1.4 Clock Control
2005-10-20 V1.5; UMa: Installation procedure changed
Default jumper settings changed: HWWD is enabled (S3:EN_X)
Def. jumper settings corrected: SL260 is open, SL262 is closed
2006-01-17 V1.6; UMa: Typos corrected
2006-04-12 V1.7; Resistors on adapter board can be removed; Changed software
installation procedure; Added SK-91F467D-208PFV
This document contains 41 pages.

Getting Started
Warranty and Disclaimer
© Fujitsu Microelectronics Europe GmbH - 3 - MCU-AN-391005-E-V17
Warranty and Disclaimer
To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts
its warranties and its liability for all products delivered free of charge (e.g. software include or
header files, application examples, target boards, evaluation boards, engineering samples of IC’s
etc.), its performance and any consequential damages, on the use of the Product in accordance with
(i) the terms of the License Agreement and the Sale and Purchase Agreement under which
agreements the Product has been delivered, (ii) the technical descriptions and (iii) all accompanying
written materials. In addition, to the maximum extent permitted by applicable law, Fujitsu
Microelectronics Europe GmbH disclaims all warranties and liabilities for the performance of the
Product and any consequential damages in cases of unauthorised decompiling and/or reverse
engineering and/or disassembling. Note, all these products are intended and must only be used
in an evaluation laboratory environment.
1. Fujitsu Microelectronics Europe GmbH warrants that the Product will perform substantially in
accordance with the accompanying written materials for a period of 90 days form the date of
receipt by the customer. Concerning the hardware components of the Product, Fujitsu
Microelectronics Europe GmbH warrants that the Product will be free from defects in material
and workmanship under use and service as specified in the accompanying written materials
for a duration of 1 year from the date of receipt by the customer.
2. Should a Product turn out to be defect, Fujitsu Microelectronics Europe GmbH’s entire liability
and the customer’s exclusive remedy shall be, at Fujitsu Microelectronics Europe GmbH’s
sole discretion, either return of the purchase price and the license fee, or replacement of the
Product or parts thereof, if the Product is returned to Fujitsu Microelectronics Europe GmbH in
original packing and without further defects resulting from the customer’s use or the transport.
However, this warranty is excluded if the defect has resulted from an accident not attributable
to Fujitsu Microelectronics Europe GmbH, or abuse or misapplication attributable to the
customer or any other third party not relating to Fujitsu Microelectronics Europe GmbH.
3. To the maximum extent permitted by applicable law Fujitsu Microelectronics Europe GmbH
disclaims all other warranties, whether expressed or implied, in particular, but not limited to,
warranties of merchantability and fitness for a particular purpose for which the Product is not
designated.
4. To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH’s
and its suppliers´ liability is restricted to intention and gross negligence.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES
To the maximum extent permitted by applicable law, in no event shall Fujitsu
Microelectronics Europe GmbH and its suppliers be liable for any damages whatsoever
(including but without limitation, consequential and/or indirect damages for personal
injury, assets of substantial value, loss of profits, interruption of business operation,
loss of information, or any other monetary or pecuniary loss) arising from the use of
the Product.
Should one of the above stipulations be or become invalid and/or unenforceable, the remaining
stipulations shall stay in full effect

Getting Started
Contents
MCU-AN-391005-E-V17 - 4 - © Fujitsu Microelectronics Europe GmbH
Contents
REVISION HISTORY.............................................................................................................. 2
WARRANTY AND DISCLAIMER........................................................................................... 3
CONTENTS............................................................................................................................ 4
1INTRODUCTION................................................................................................................ 6
2HARDWARE REQUIREMENTS........................................................................................ 7
3SOFTWARE INSTALLATION ........................................................................................... 8
3.1 Softune Workbench................................................................................................... 8
4INSTALLATION OF THE EMULATION SYSTEM............................................................. 9
4.1 Providing a Clock Source.......................................................................................... 9
4.2 Checking the Jumpers .............................................................................................. 9
4.3 Connecting the Emulation System.......................................................................... 10
4.3.1 Cabling the Emulator MB2198-01............................................................. 10
4.3.2 Mounting the Evaluation MCU .................................................................. 11
4.3.3 Connecting and Cabling the Adapter Board to the Evaluation Board....... 12
4.3.3.1 Connecting the Adapter Board to the SK-91460-MAIN ............ 12
4.3.3.2 Connecting the Adapter Board to the SK-91F467D-208PFV.... 13
4.4 Power up the Emulation System............................................................................. 14
5JUMPERS AND SWITCHES ........................................................................................... 15
5.1 Jumpers of the MB91V460 Adapter Board (MB2198-300) ..................................... 15
5.1.1 V-Chip Options.......................................................................................... 15
5.1.2 Emulator Interface..................................................................................... 16
5.1.3 External Emulation Memory...................................................................... 17
5.1.4 Clock Control............................................................................................. 18
5.1.5 Power Settings.......................................................................................... 19
5.1.6 Signal Routing........................................................................................... 20
5.1.7 Default Jumper Settings............................................................................ 21
5.2 Jumpers of the evaluation board SK-91460-MAIN V1.2......................................... 22
5.2.1 Analogue Power Supply Voltage............................................................... 22
5.2.2 Default Jumper Settings............................................................................ 23
5.3 Default Jumper Settings of the evaluation board SK-91F467D-208PFV................ 24
5.4 Default Jumpers Settings of the probe cable PB-91467D-208PFV ........................ 25
5.5 Default Jumpers Settings of the probe cable PB-91467D-LS-208PFV................... 26

Getting Started
Contents
© Fujitsu Microelectronics Europe GmbH - 5 - MCU-AN-391005-E-V17
6SOFTUNE WORKBENCH GETTING STARTED............................................................ 27
6.1 Copying the “template” directory............................................................................. 27
6.2 Adjusting the project files........................................................................................ 27
6.3 Opening the Softune Workbench............................................................................ 28
6.4 Entering the code.................................................................................................... 30
6.5 Compiling the Project.............................................................................................. 30
6.6 Enter Debugging Mode........................................................................................... 30
6.7 Executing the Program............................................................................................ 31
6.8 Ending the Debugging ............................................................................................ 31
6.9 Last steps................................................................................................................ 31
7SETUP / CHANGE CONNECTION PC – EMULATION SYSTEM .................................. 32
7.1 Setup Serial Connection ......................................................................................... 32
7.1.1 Overview................................................................................................... 32
7.1.2 Settings..................................................................................................... 32
7.2 Setup USB .............................................................................................................. 32
7.2.1 Overview................................................................................................... 32
7.2.2 Updating the USB-Drivers......................................................................... 32
7.3 Setup LAN............................................................................................................... 34
7.3.1 Overview................................................................................................... 34
7.3.2 Configuring the LAN Adapter.................................................................... 35
7.3.3 Configuring Operating System “WindowsTM”............................................. 36
7.3.4 Checking the network-connection............................................................. 38
7.3.5 Troubleshooting ........................................................................................ 38
7.3.6 Softune Workbench................................................................................... 40
8APPENDIX....................................................................................................................... 41
8.1 Figures.................................................................................................................... 41

Getting Started
Chapter 1 Introduction
MCU-AN-391005-E-V17 - 6 - © Fujitsu Microelectronics Europe GmbH
1 Introduction
The chapter gives short overview of this application note.
This application note describes the first steps how to use the MB91460 emulation system. It
describes also the software and hardware installation procedure.
Further information can be found in the following manuals:
- ‘Softune Workbench Installation Manual for V6’ for information about the installation
procedure of the software
- ‘MB2198-01 Hardware Manual’ for information about the emulator
- ‘SK-91460-MAIN V1.2 User Guide’ for information about the evaluation board SK-
91460-MAIN and its jumpers and options.
- ‘SK-91F467D-208PFV V1.1 User Guide’ for information about the evaluation board
SK-91F467D-208PFV and its jumpers and options.
- ‘PB-91467D-208PFV User Guide’ for information about the probe cable PB-91467D-
208PFV and its jumpers and options.
The MB91460 emulation system allows the designer immediately to start with the software
development before his own final target system is available.

Getting Started
Chapter 2 Hardware Requirements
© Fujitsu Microelectronics Europe GmbH - 7 - MCU-AN-391005-E-V17
2 Hardware Requirements
The chapter lists the required hardware for the MB91460 emulation system.
The MB91460 emulator system consists of
- the emulator MB2198-01 incl. 16 V DC power supply
- the DSU-FR cable MB2198-10
- the MB91V460 adapter board (MB2198-300) incl. 16 V DC power supply
- and an evaluation board, e.g.
- the evaluation board SK-91460-MAIN V1.2 incl. 9 V DC power supply
or
- the evaluation board SK-91F467-208PFV V1.1 incl. 9 V DC power supply and
- the probe cable PB-91467-208PFV or the probe cable PB-91467-LS-208PFV

Getting Started
Chapter 3 Software Installation
MCU-AN-391005-E-V17 - 8 - © Fujitsu Microelectronics Europe GmbH
3 Software Installation
This chapter describes the software installation procedure
This installation procedure is valid for Windows XP/2000/NT 4.0. For other operating
systems and for further details, please refer to the Softune Workbench installation manual
for V6 and to the hardware manual of the Emulator MB2198-01
3.1 Softune Workbench
Please install the Softune Propack 911s FRSTAPACK600007FME02
1. Execute FRSTAPACK600007FME02 and follow installation process.
Rule 1: To install the software under Windows XP/2000/NT 4.0, the user requires
administration authority.

Getting Started
Chapter 4 Installation of the Emulation System
© Fujitsu Microelectronics Europe GmbH - 9 - MCU-AN-391005-E-V17
4 Installation of the Emulation System
This chapter describes, what should be considered and checked before power-up the
emulation system. Also the start-up procedure of the emulation system is described.
In order to properly install the emulation system, please follow the following steps.
4.1 Providing a Clock Source
The adapter board can be equipped with two clocks, a main and a sub clock. The following
figure depicts who to install the crystal and the capacities for the main clock in connector
SC30. The same applies analogously for the sub clock in connector SC31.
Figure 1: Installing the crystal for the main clock
The crystal for the main clock has a frequency of 4 MHz and the crystal for the sub clock has
a frequency of 32 kHz. The capacity of the capacitor should be 22 pF.
4.2 Checking the Jumpers
Rule 2: To prevent damages, check all jumpers and switches before powering up the
emulation system.
Jumpers of the MB91V460 adapter board (MB2198-300) and all jumpers of the evaluation
board SK-91460-MAIN V1.2 or SK-91F467D-208PFV and the probe cable PB-91467D-
208PFV influencing the adapter board are described in chapter 5.

Getting Started
Chapter 4 Installation of the Emulation System
MCU-AN-391005-E-V17 - 10 - © Fujitsu Microelectronics Europe GmbH
4.3 Connecting the Emulation System
The following connections have to be established:
4.3.1 Cabling the Emulator MB2198-01
There are some connections necessary for the emulator MB2198-01. The following lists
each step.
1. Connect the emulator MB2198-01 (1) e.g. with the USB-Cable (2) to the USB port of
the PC. (Analogously for other connection types. Please also refer to chapter 7)
2. Plug the DSU-FR Cable MB2198-10 (3) into the port labelled ‘DSU Cable’ (4). The
correct position of cable and port is marked with arrows.
3. Finally, connect the 16 V DC power supply (5) to the port ‘DC in’ (6) and to 230 V.
Please, be aware, that the emulator is switched off.
Figure 2 illustrates the necessary connections of the emulator MB2198-01.
Figure 2: Connections of the Emulator MB2198-01

Getting Started
Chapter 4 Installation of the Emulation System
© Fujitsu Microelectronics Europe GmbH - 11 - MCU-AN-391005-E-V17
4.3.2 Mounting the Evaluation MCU
1. Press down the top of the IC socket. Take care when you press the IC socket; Hold
the board against the pressure not to bend the board.
2. Confirm that the hook is open, and put the evaluation MCU on the socket. The index
shows the A1 pin of the evaluation MCU.
3. Release the socket slowly and confirm that the evaluation MCU is fastening to the
socket.
The following figure shows the socket of the evaluation MCU MB91V460.
Figure 3: Mounting the Evaluation MCU

Getting Started
Chapter 4 Installation of the Emulation System
MCU-AN-391005-E-V17 - 12 - © Fujitsu Microelectronics Europe GmbH
4.3.3 Connecting and Cabling the Adapter Board to the Evaluation Board
Depending on the evaluation board, a probe cable is required or not. The following sections
describe the connection of the adapter board to the evaluation board SK-91460-Main or to
the evaluation board SK-91F467D-208PFV with the probe cable PB-91467D-208PFV or PB-
91467D-LS-208PFV
4.3.3.1 Connecting the Adapter Board to the SK-91460-MAIN
1. Connect both boards. Be aware, that the boards are tight connected.
Figure 4 shows the connected boards.
Figure 4: Connected Adapter Board and Evaluation Board
After connecting both boards together it is necessary to connect the DSU-FR Cable
MB2198-10 and the power supplies.
2. Connect the DSU-FR Cable MB2198-10 to the evaluation board.
3. Connect the 16 V DC power supply to the port ‘DC in’ and to 230 V. Please, be
aware, that ‘SW2 Power’ is off.
4. Provide the 9 V DC power supply and connect it to 230 V. The following figure shows
the correct polarisation. Do not power up the evaluation board by connecting the
power supply yet.
Figure 5: The Correct Polarisation of the 9 V DC Power Supply.
9 VGND

Getting Started
Chapter 4 Installation of the Emulation System
© Fujitsu Microelectronics Europe GmbH - 13 - MCU-AN-391005-E-V17
Figure 6 shows the cabling of the adapter and evaluation boards.
Figure 6: Cabling the Adapter Board and Evaluation Board
4.3.3.2 Connecting the Adapter Board to the SK-91F467D-208PFV
1. Connect the adapter board with the probe cable. Be aware, that the boards are tight
connected.
2. Unscrew the YQ-PACK of the SK-91F467D-208PFV and remove carefully the
microcontroller from the socket.
3. Connect the probe cable PB-91467D-208PFV to the SK-91F467D-208PFV and
tighten the screw.
The same procedure applies for the probe cable PB-91467D-LS-208PFV.
Figure 7 shows the connected boards.
Figure 7: Connected Adapter Board, Probe Cable and Evaluation Board

Getting Started
Chapter 4 Installation of the Emulation System
MCU-AN-391005-E-V17 - 14 - © Fujitsu Microelectronics Europe GmbH
After connecting the boards it is necessary to connect the DSU-FR Cable MB2198-10 and
the power supplies.
5. Connect the DSU-FR Cable MB2198-10 to the evaluation board.
6. Connect the 16 V DC power supply to the port ‘DC in’ and to 230 V. Please, be
aware, that ‘SW2 Power’ is off.
7. Provide the 9 V DC power supply and connect it to 230 V. The following figure shows
the correct polarisation. Do not power up the evaluation board by connecting the
power supply yet.
Figure 8: The Correct Polarisation of the 9 V DC Power Supply.
The following figure shows the cabling of the boards.
Figure 9: Cabling the Adapter Board, Probe Cable and Evaluation Board
4.4 Power up the Emulation System
To avoid damages, please always follow this procedure to power up the emulation system.
1. Switch on the main switch at the back of the emulator MB2198-01. The ‘Power’ LED
and the ‘UVCC’ LED have to be illuminated.
2. Power on the MB91V460 Adapter Board (MB2198-300) ‘SW2 Power’. The ‘Power’
LED has to be illuminated.
3. Power on the evaluation board SK-91460-MAIN V1.2
Rule 3: To power down the emulation system, please follow the procedure reversely.
9 VGND

Getting Started
Chapter 5 Jumpers and Switches
© Fujitsu Microelectronics Europe GmbH - 15 - MCU-AN-391005-E-V17
5 Jumpers and Switches
This chapter describes the jumpers and switches which can be modified on the MB91V460
adapter board (MB2198-300). Also the jumpers of the evaluation board SK-91460-MAIN
V1.2 influencing the adapter board are explained. The default settings are mentioned.
5.1 Jumpers of the MB91V460 Adapter Board (MB2198-300)
5.1.1 V-Chip Options
Some options of the V-chip can be enabled or disabled.
Jumper Setting Description
EN – X Old alarm comparatorS1
ALARM_SEL X – DIS New alarm comparator
EN – X 5V ADC is enabledS2
ADC_SEL X – DIS 3V ADC is enabled
EN – X Hardware watchdog is disabledS3
HWWDG_KILL X – DIS Hardware watchdog is enabled
EN – X Fixed Mode / Reset Vector is enabledS4
FIX_ENX X – DIS Fixed Mode / Reset Vector is disabled
EN – X Clock supervisor is disabledS5
CSV_KILL X – DIS Clock supervisor is enabled
EN – X Flash ModeS6
SRAM_SFX X – DIS SRAM Mode
EN – X Disable flash security of emulation flashS7
FSC_DISABLE X – DIS Enable flash security of emulation flash
Default: S1 = X–DIS S2 = EN–X S3 = X-DIS
S4 = EN–X S5 = X–DIS S6 = X–DIS S7 = EN–X
Note:
1) ALARM_SEL: The 91V460 is equipped with two different alarm comparators. The
devices 91F467D and 91461 are equipped with the new alarm comparator.
2) ADC_SEL: Depending on the voltage supply the respective ADC have to be
selected.
3) HWWDG_KILL: The hardware watchdog has to be enabled also in the Softune
workbench.
(Debug Mode: Setup-> Dev. Environment-> Dev. Environment-> Execution->
watchdog)
4) SRAM_SFX: Depending on the connected emulation memory, the respective mode
has to be selected. By default a SRAM is connected.

Getting Started
Chapter 5 Jumpers and Switches
MCU-AN-391005-E-V17 - 16 - © Fujitsu Microelectronics Europe GmbH
5.1.2 Emulator Interface
The emulator interface can be terminated if the in-circuit-emulator (ICE) is not used.
Jumper Setting Description
USER – INITX INITX is controlled by the evaluation boardS14
INITX INITX – ICE INITX is controlled by the emulator
USER – TRSTX TRSTX is controlled by the evaluation boardS15
TRSTX TRSTX – ICE TRSTX is controlled by the emulator
PD_OFF – ICD3 Disconnect pull-down resistor to ICD3S16
ICD3 ICD3 – PD_ON Connect pull-down resistor to ICD3
PD_OFF – ICD2 Disconnect pull-down resistor to ICD2S17
ICD2 ICD2 – PD_ON Connect pull-down resistor to ICD2
PD_OFF – ICD1 Disconnect pull-down resistor to ICD1S18
ICD1 ICD1 – PD_ON Connect pull-down resistor to ICD1
PD_OFF – ICD0 Disconnect pull-down resistor to ICD0S19
ICD0 ICD0 – PD_ON Connect pull-down resistor to ICD0
PD_OFF – BREAK Disconnect pull-down resistor to BREAKS20
BREAK BREAK – PD_ON Connect pull-down resistor to BREAK
Default: S14 = INITX–ICE S15 = TRSTX–ICE S20 = BREAK-ON
S16 = OFF–ICD3 S17 = OFF–ICD2 S18 = OFF–ICD1
S20 = OFF–ICD0
Note:
1) If the in-circuit-emulator (ICE) is used, the default settings have to be used.

Getting Started
Chapter 5 Jumpers and Switches
© Fujitsu Microelectronics Europe GmbH - 17 - MCU-AN-391005-E-V17
5.1.3 External Emulation Memory
The size of the external emulation memory and the emulation memory width is selectable.
Jumper Setting Description
D32 – X External emulation memory is used in a 32 bit widthS13
D32_D16SL X – D16 External emulation memory is used in a 16 bit width
Jumper MDENS2 MDENS1 MDENS0 Size
1 1 1 8 MByte
1 1 0 4 MByte
1 0 1 2 MByte
1 0 0 1 MByte
0 1 1 512 kByte
0 1 0 Prohibited
0 0 1 Prohibited
S10 MDENS1
S11 MDENS0
S12 MDENS2
0 0 0 0 Byte
Default: S13 = D32-X
MDENS0 = 0 MDENS1 = 0 MDENS2 = 0

Getting Started
Chapter 5 Jumpers and Switches
MCU-AN-391005-E-V17 - 18 - © Fujitsu Microelectronics Europe GmbH
5.1.4 Clock Control
The source of the main and the sub clock is selectable between the adapter board and the
evaluation board. MCLKI and MCLKO of the external bus interface can be connected to the
evaluation board or can be shorten on the adapter board.
Jumper Setting Description
EML – X0 Main clock provided from adapter board
S22 X0 - USER Main clock provided from evaluation board
EML – X1 Main clock provided from adapter board
S23 X1 - USER Main clock provided from evaluation board
EML – X0A Sub clock provided from adapter board
S24 X0A - USER Sub clock provided from evaluation board
EML – X1A Sub clock provided from adapter board
S25 X1A - USER Sub clock provided from evaluation board
EVA – MCLKI
EVA – MCLKO MCLKI and MCLKO are not connected to
evaluation board. MCLKI and MCLKO are shorten
S30 / S31
MCLKI / MCLKO MCLKI – USER
MCLKO – USER
MCLKI and MCLKO are connected to evaluation
board. MCLKI and MCLKO are not shorten
Default: S22 = EML-X0 S23 = EML-X1 S24 = EML-X0A
S25 = EML-X1A
S30 = MCLKI-USER S31 = MCLKO-USER
By default the clocks are provided from the adapter board.
By default MCLKI and MCLKO are connected to the evaluation board.

Getting Started
Chapter 5 Jumpers and Switches
© Fujitsu Microelectronics Europe GmbH - 19 - MCU-AN-391005-E-V17
5.1.5 Power Settings
The voltage sources are selectable.
Jumper Setting Description
UVCC5 – SHDNSEL Keep watching VCC5 of evaluation boardS26
SHDNSEL SHDNSE – UVCC3 Keep watching VCC3 of evaluation board
3.3V – VCCC3SEL MB91V460’s VCC3 is supplied by evaluation board
S27
VCCC3SEL VCCC3SEL – 3.5V 3.5V is supplied to VCC3 of MB91V460
UVCC3 – VCC5 Connect VCC3 of the adapter board to VCC3 of
evaluation board
S28
VCC5 VCC5 – UVCC5 Connect VCC5 of the adapter board to VCC5 of
evaluation board
UVCC5 – UVCC3H VCC5H is generated from VCC5 by adding +1 V
S29
UVCC3H UVCC3H – UVCC3 VCC5H is generated from VCC3 by adding +1 V
VCC3 – C Connect to VCC3 of MB91V460
S8
CC – VCC3C Connect to the C terminal of the evaluation board
Default: S26 =
SHDNSEL–UVCC3 S27 = VCCC3SEL–3.5V
S28 = VCC5–UVCC5 S29 = UVCC3H–UVCC3
S8 = VCC3 – C
Note:
1) SHDNSEL: VCC3 or VCC5 can be supervised. If the selected voltage fails, the power
supply of the evaluation chip will be cancelled.

Getting Started
Chapter 5 Jumpers and Switches
MCU-AN-391005-E-V17 - 20 - © Fujitsu Microelectronics Europe GmbH
5.1.6 Signal Routing
Some signal can be routed depending on the application of the evaluation board.
Jumper Setting Description
PULLDOWN – P10_7 Pull-down resistor is connected to P10_7
S21
P10_7 P10_7 – PULLUP Pull-up resistor is connected to P10_7
P224 – CN2_B68
P242 – CN3_A6 P22_4 is connected to CN2_B68
P24_2 is connected to CN3_A6
S32/S33
P224/P242 P224 – CN3_A6
P242 – CN2_B68 P22_4 is connected to CN3_A6
P24_2 is connected to CN2_B68
P225 – CN2_B67
P243 – CN3_A5 P22_5 is connected to CN2_B67
P24_3 is connected to CN3_A5
S34/S35
P225/P243 P225 – CN3_A5
P243 – CN2_B67 P22_5 is connected to CN3_A5
P24_3 is connected to CN2_B67
Default: S21 = PULLDOWN – P10_7
S32 = P224 – CN2_B68 S33 = P242 – CN3_A6
S34 = P225 – CN2_B67 S35 = P243 – CN3_A5