Fujitsu Eternus DX80 S2 User manual

ETERNUS DX80 S2/DX90 S2
Disk storage system
User's Guide -Operation-
P3AM-4842-12ENZ0

This page is intentionally left blank.

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
3
Preface
Fujitsu would like to thank you for purchasing our ETERNUS DX80 S2/DX90 S2 Disk storage system.
The ETERNUS DX80 S2/DX90 S2 Disk storage system is designed to be connected to a Fujitsu (PRIMEQUEST or
PRIMERGY) or non-Fujitsu servers.
This manual describes operation management and maintenance for the ETERNUS DX80 S2/DX90 S2 Disk
storage system.
This manual is intended for use of ETERNUS DX Disk storage system in regions other than Japan.
Please carefully review the information outlined in this manual.
Twelfth Edition
June 2013
Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.
IBM, AIX, and Tivoli are trademarks of International Business Machines Corporation, registered in many
jurisdictions worldwide.
The company names, product names and service names mentioned in this document are registered
trademarks or trademarks of their respective companies.
Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
4
About this Manual
Organization
This document is composed of the following seven chapters and three appendices:
●Chapter 1 Components
This chapter describes the components of the ETERNUS DX80 S2/DX90 S2 Disk storage system.
●Chapter 2 Basic Operation
This chapter explains how to turn on and off the ETERNUS DX80 S2/DX90 S2 Disk storage system and how
to operate the FUNCTION button on the controller enclosure.
●Chapter 3 Setup
This chapter describes the required settings for operation of the ETERNUS DX80 S2/DX90 S2 Disk storage
system and provides notes for setting up each function of the ETERNUS DX80 S2/DX90 S2 Disk storage
system.
●Chapter 4 Operations
This chapter describes the control of the LAN for operation management of the ETERNUS DX80 S2/DX90 S2
Disk storage system, and the monitoring the status of the ETERNUS DX80 S2/DX90 S2 Disk storage system.
●Chapter 5 Maintaining Optional Products
This chapter explains how to install optional products in the ETERNUS DX80 S2/DX90 S2 Disk storage
system.
●Chapter 6 Maintenance
This chapter describes maintenance for the ETERNUS DX80 S2/DX90 S2 Disk storage system.
●Chapter 7 Troubleshooting
This chapter explains troubleshooting when errors occur in the ETERNUS DX80 S2/DX90 S2 Disk storage
system.
"Event Notification Message List", "Audit Log List", and "Event (SNMP Trap) Display When Using ServerView
Operation Manager" are described as appendices.

About this Manual
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
5
Warning Notations
Warning signs are shown throughout this manual in order to prevent injury to the user and/or material
damage. These signs are composed of a symbol and a message describing the recommended level of caution.
The following section explains the symbols, their levels of caution, and their meanings as used in this manual.
The following symbols are used to indicate the type of warnings or cautions being described.
WARNING
This symbol indicates the possibility of serious or fatal injury if the ETERNUS
DX80 S2/DX90 S2 Disk storage system is not used properly.
CAUTION
This symbol indicates the possibility of minor or moderate personal injury, as
well as damage to the ETERNUS DX Disk storage system and/or to other users
and their property, if the ETERNUS DX80 S2/DX90 S2 Disk storage system is not
used properly.
This symbol indicates IMPORTANT information for the user to note when using
the ETERNUS DX80 S2/DX90 S2 Disk storage system.
Electric Shock
The triangle emphasizes the urgency of the WARNING and CAUTION
contents. Inside the triangle and above it are details concerning the symbol
(e.g. Electrical Shock).
No Disassembly
The barred "Do Not..." circle warns against certain actions. The action
which must be avoided is both illustrated inside the barred circle and written
above it (e.g. No Disassembly).
Unplug
The black "Must Do..." circle indicates actions that must be taken. The
required action is both illustrated inside the black disk and written above it
(e.g. Unplug).

About this Manual
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
6
How Warnings are Presented in this Manual
A message is written beside the symbol indicating the caution level. This message is marked with a vertical
ribbon in the left margin, to distinguish this warning from ordinary descriptions.
An example is shown here.
Additional Information
Symbols Used in This Manual
The following is a symbol used throughout this manual:
Abbreviations Used in This Manual
•"ETERNUS DX Disk storage system" refers to the DX80 S2/DX90 S2 Disk storage system.
•"CA" refers to a host interface module that is used in an ETERNUS DX Disk storage system to connect to a
server.
•"Host Bus Adapter (HBA)" refers to the interface module that is normally used by the server to connect to
ETERNUS DX Disk storage systems.
An "FC card", "LAN card", "Network Interface Card (NIC)", "Converged Network Adapter (CNA)", or "SAS card"
may be used instead, depending on the server and interface.
•Trademark symbols such as ™ and ® are omitted in this document.
Warning Level Indicator
Warning Type Indicator
Warning Details
To avoid damaging the ETERNUS DX80 S2/DX90 S2
Disk storage system, pay attention to the following points when cleaning
the ETERNUS DX80 S2/DX90 S2 Disk storage system:
- Make sure to disconnect the power when cleaning.
- Be careful that no liquid seeps into the ETERNUS DX80 S2/DX90 S2
Disk storage system when using cleaners, etc.
- Do not use alcohol or other solvents to clean
the ETERNUS DX80 S2/DX90 S2 Disk storage system.
Warning Layout Ribbon
Example Warning
Functions and know how which can be useful when setting up or operating the
ETERNUS DX80 S2/DX90 S2 Disk storage system.

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
7
Table of Contents
Chapter 1 Components 12
1.1 Controller Enclosure .......................................................................................................... 12
1.1.1 Front ..............................................................................................................................................................12
1.1.2 Rear ............................................................................................................................................................... 13
1.1.3 Components (Front) ...................................................................................................................................... 14
1.1.4 Components (Rear) .......................................................................................................................................17
1.2 Drive Enclosures ................................................................................................................ 23
1.2.1 Front ..............................................................................................................................................................23
1.2.2 Rear ............................................................................................................................................................... 24
1.2.3 Components (Front) ...................................................................................................................................... 24
1.2.4 Components (Rear) .......................................................................................................................................27
1.3 Power Distribution Units (for Regions other than EMEA&I) ............................................... 29
1.3.1 Power Distribution Units (1U) ........................................................................................................................29
1.3.2 Power Distribution Units (2U) ........................................................................................................................30
Chapter 2 Basic Operation 32
2.1 Powering On and Off .........................................................................................................32
2.1.1 Switching On and Off the Main Line Switch on the Power Distribution Unit
(for Regions Other than EMEA&I) .................................................................................................................. 32
2.1.2 Switching On and Off the PSU Switch on the Power Supply Unit ....................................................................35
2.1.3 Powering On ..................................................................................................................................................36
2.1.4 Powering Off ..................................................................................................................................................38
2.2 Using the FUNCTION Button .............................................................................................. 39
Chapter 3 Setup 41
3.1 Thin Provisioning Setup .................................................................................................... 41
3.1.1 Registering the Thin Provisioning Feature License ........................................................................................41
3.1.2 Thin Provisioning Setup ................................................................................................................................. 42
3.1.3 Restrictions and Notes When Using the Thin Provisioning Function .............................................................. 42
3.2 Flexible Tier (Auto Storage Layering) Setup ...................................................................... 44
3.2.1 Registering the Thin Provisioning Feature License ........................................................................................44
3.2.2 Flexible Tier Setup ......................................................................................................................................... 45
3.2.3 Restrictions and Notes ................................................................................................................................... 45
3.3 Storage Migration ............................................................................................................. 47

Table of Contents
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
8
3.4 Data Encryption ................................................................................................................ 48
3.5 Key Management Server Linkage ...................................................................................... 50
3.6 Eco-mode .......................................................................................................................... 51
3.7 Optimizing Volume Configurations ................................................................................... 53
3.7.1 RAID Migration ..............................................................................................................................................54
3.7.2 Logical Device Expansion (LDE) .....................................................................................................................55
3.7.3 LUN Concatenation ........................................................................................................................................56
3.7.4 Wide Striping .................................................................................................................................................57
Chapter 4 Operations 58
4.1 LAN for Operation Management ....................................................................................... 58
4.2 Monitoring ETERNUS DX Disk Storage System Status ........................................................ 60
4.2.1 LED Status Check ........................................................................................................................................... 60
4.2.2 Displaying Status via ETERNUS Web GUI ........................................................................................................ 61
4.2.3 Event Notification .......................................................................................................................................... 62
4.2.4 Audit Log ....................................................................................................................................................... 63
Chapter 5 Maintaining Optional Products 64
5.1 Installing Drives ................................................................................................................ 64
5.1.1 Installation Rules for Drives ...........................................................................................................................65
5.1.2 Installable Drives ...........................................................................................................................................65
5.1.3 Drive Handling Instructions ...........................................................................................................................66
5.1.4 Additional Drive Installation Procedure .........................................................................................................67
5.2 Installing Drive Enclosures ................................................................................................ 72
5.2.1 Installation Rules for Drive Enclosures ........................................................................................................... 72
5.2.2 Installable Drive Enclosures ...........................................................................................................................72
5.2.3 Drive Enclosure Handling Instructions ...........................................................................................................72
5.2.4 Additional Drive Enclosure Installation ..........................................................................................................73
5.3 Installing Host Interfaces ..................................................................................................85
5.3.1 Installation Rules for Host Interfaces .............................................................................................................85
5.3.2 Installable Host Interfaces ............................................................................................................................. 86
5.3.3 Host Interface Handling Instructions ............................................................................................................. 86
5.4 Installing Long Wave SFP+ Modules (16Gbit/s) ................................................................. 87
5.4.1 Installation Rules for Long Wave SFP+ Modules (16Gbit/s) ............................................................................ 87
5.4.2 Installable Long Wave SFP+ Modules (16Gbit/s) ............................................................................................88
5.4.3 SFP+ Module Handling Instructions ...............................................................................................................88
5.4.4 Long Wave SFP+ Modules (16Gbit/s) Installation Procedure ..........................................................................89

Table of Contents
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
9
Chapter 6 Maintenance 93
6.1 Periodic Backup ................................................................................................................ 93
6.2 Volume Formatting Time .................................................................................................. 93
6.3 Rebuild/Copyback Process Time ........................................................................................ 94
6.4 Maintenance Service .........................................................................................................95
6.4.1 Maintenance Support Period ......................................................................................................................... 95
6.4.2 Related Service ..............................................................................................................................................95
Chapter 7 Troubleshooting 96
7.1 Check List .......................................................................................................................... 96
7.2 Required Information for Inquiries .................................................................................. 102
Appendix A Event Notification Message List 103
A.1 Message Format .............................................................................................................. 103
A.1.1 E-mail.......................................................................................................................................................... 103
A.1.2 Syslog.......................................................................................................................................................... 105
A.1.3 SNMP........................................................................................................................................................... 107
A.1.4 Host Sense................................................................................................................................................... 111
A.2 Message List.................................................................................................................... 112
A.2.1 Common Terms............................................................................................................................................ 112
A.2.2 Error Messages ............................................................................................................................................ 113
A.2.3 Warning Messages ...................................................................................................................................... 133
A.2.4 Informational Messages .............................................................................................................................. 143
A.2.5 Test Messages ............................................................................................................................................. 149
A.2.6 Sense Codes................................................................................................................................................. 149
Appendix B Audit Log List 154
Appendix C Event (SNMP Trap) Display When Using
ServerView Operation Manager 183

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
10
List of Figures
Figure 1.1 Front view of a 2.5" type controller enclosure.............................................................................................. 12
Figure 1.2 Front view of a 3.5" type controller enclosure.............................................................................................. 12
Figure 1.3 Rear view of a controller enclosure (single-controller type) ........................................................................ 13
Figure 1.4 Rear view of a controller enclosure (dual-controller type)........................................................................... 13
Figure 1.5 Operation panel (2.5" type controller enclosure)......................................................................................... 14
Figure 1.6 Operation panel (3.5" type controller enclosure)......................................................................................... 14
Figure 1.7 2.5" drive..................................................................................................................................................... 16
Figure 1.8 Drive slot numbers (2.5" type controller enclosure)..................................................................................... 16
Figure 1.9 3.5" drive..................................................................................................................................................... 16
Figure 1.10 Drive slot numbers (3.5" type controller enclosure)..................................................................................... 16
Figure 1.11 Controller .................................................................................................................................................... 17
Figure 1.12 Host interface (FC, iSCSI 10Gbit/s, FCoE (for FC cable connection)).............................................................. 19
Figure 1.13 Host interface (iSCSI 10Gbit/s, FCoE (for Copper Twinax cable connection)) ................................................ 20
Figure 1.14 Host interface (iSCSI 1Gbit/s)....................................................................................................................... 20
Figure 1.15 Host interface (SAS) .................................................................................................................................... 21
Figure 1.16 Power supply unit........................................................................................................................................ 21
Figure 1.17 Front view of a 2.5" type drive enclosure ..................................................................................................... 23
Figure 1.18 Front view of a 3.5" type drive enclosure ..................................................................................................... 23
Figure 1.19 Rear view of a drive enclosure (single-IOM type) ........................................................................................ 24
Figure 1.20 Rear view of a drive enclosure (dual-IOM type)........................................................................................... 24
Figure 1.21 LEDs on the front side of the drive enclosure .............................................................................................. 25
Figure 1.22 2.5" drive..................................................................................................................................................... 25
Figure 1.23 Drive slot numbers (2.5" type drive enclosure)............................................................................................ 26
Figure 1.24 3.5" drive..................................................................................................................................................... 26
Figure 1.25 Drive slot numbers (3.5" type drive enclosure)............................................................................................ 26
Figure 1.26 I/O module .................................................................................................................................................. 27
Figure 1.27 Power supply unit........................................................................................................................................ 28
Figure 1.28 Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 1U, Max 2 enclosures connection).................. 29
Figure 1.29 Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 2U, Max 6 enclosures connection).................. 30
Figure 1.30 Power distribution unit for DX80 S2/DX90 S2 (AC200-240V, 2U, Max 8 enclosures connection).................. 31
Figure 2.1 ON position (marked "|") of the main line switches on a 1U power distribution unit................................... 32
Figure 2.2 ON position (marked "|") of the main line switches on a 2U power distribution unit................................... 33
Figure 2.3 OFF position (marked "O") of the main line switches on a 1U power distribution unit................................. 33
Figure 2.4 OFF position (marked "O") of the main line switches on a 2U power distribution unit................................. 34
Figure 2.5 ON position (marked "|") of the PSU switch on a power supply unit ............................................................ 35
Figure 2.6 OFF position (marked "O") of the PSU switch on a power supply unit .......................................................... 36
Figure 3.1 System configuration for linking with the key management server............................................................. 50
Figure 4.1 LAN control (switching of the Master CM) ................................................................................................... 59
Figure 4.2 LAN control (when the IP address of the Slave CM is set) ............................................................................ 59
Figure 4.3 ETERNUS Web GUI screen ............................................................................................................................ 61
Figure 4.4 Event notification........................................................................................................................................ 63
Figure 4.5 Audit logs .................................................................................................................................................... 63
Figure 5.1 Positions of 2.5" drive slots.......................................................................................................................... 65
Figure 5.2 Positions of 3.5" drive slots.......................................................................................................................... 65
Figure 5.3 Installation diagram for a host interface (single-controller type)................................................................ 85
Figure 5.4 Installation diagram for host interfaces (dual-controller type).................................................................... 86

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
11
List of Tables
Table 1.1 Status and meanings of each LED (operation panel (controller enclosure))................................................ 15
Table 1.2 Status and meanings of each LED (drive).................................................................................................... 17
Table 1.3 Status and meanings of each LED (controller) ............................................................................................ 18
Table 1.4 Status and meanings of each LED (power supply unit) ............................................................................... 22
Table 1.5 Status and meanings of each LED (in front of drive enclosure) ................................................................... 25
Table 1.6 Status and meanings of each LED (drive).................................................................................................... 26
Table 1.7 Status and meanings of each LED (I/O module) .......................................................................................... 27
Table 1.8 Status and meanings of each LED (power supply unit) ............................................................................... 28
Table 4.1 General status of ETERNUS Web GUI ............................................................................................................ 61
Table 6.1 Time for volume formatting (disk) .............................................................................................................. 93
Table 6.2 Rebuild process time (disk)......................................................................................................................... 94
Table 6.3 Copyback process time (disk) ...................................................................................................................... 94

ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
12
Chapter 1
Components
This chapter describes the components of the ETERNUS DX Disk storage system.
1.1 Controller Enclosure
An operation panel and drives are installed in the front of the controller enclosure. Controllers and power
supply units are installed in the rear.
1.1.1 Front
■2.5" type
Figure 1.1 Front view of a 2.5" type controller enclosure
■3.5" type
Figure 1.2 Front view of a 3.5" type controller enclosure
Operation panel 2.5" disk or 2.5" Solid State Drive (SSD)
Flange cover Flange cover
Operation panel
Flange cover Flange cover
3.5" disk or 3.5" Solid State Drive (SSD)

Chapter 1 Components
1.1 Controller Enclosure
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
13
1.1.2 Rear
■Single-controller type
Figure 1.3 Rear view of a controller enclosure (single-controller type)
●Part explanation
•Cover
Remove this when installing an additional controller (optional).
■Dual-controller type
Figure 1.4 Rear view of a controller enclosure (dual-controller type)
Power supply unit (PSU#0) Power supply unit (PSU#1)
Controller (CM#0) Cover
Power supply unit (PSU#0) Power supply unit (PSU#1)
Controller (CM#0) Controller (CM#1)

Chapter 1 Components
1.1 Controller Enclosure
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
14
1.1.3 Components (Front)
This section describes the operation panel and the drives in the front of the controller enclosure.
■Operation panel
An operation panel has LEDs, a Power switch, and a FUNCTION button.
●2.5" type
Figure 1.5 Operation panel (2.5" type controller enclosure)
●3.5" type
Figure 1.6 Operation panel (3.5" type controller enclosure)
With a flange cover
CACHE LED
MAINT/ID LED
FAULT LED
READY LED
Power switch
POWER LED
Without a flange cover
FUNCTION button
With a flange cover
Power switch
CACHE LED
MAINT/ID LED
FAULT LED
READY LED
POWER LED
Without a flange cover
FUNCTION button

Chapter 1 Components
1.1 Controller Enclosure
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
15
●Part explanation
•Power switch
This switch is used to turn on or off the ETERNUS DX Disk storage system.
•FUNCTION button
Hold down the button for three seconds during maintenance to stop the maintenance operation. Hold
down the button for three seconds while a maintenance operation is not performed to start the
maintenance operation.
For a dual-controller type, press the button twice within three seconds during maintenance to switch the
Master CM to the other controller.
Press the button three times within three seconds during maintenance to restore the factory default
settings of the LAN ports.
•LEDs
The states of LEDs are listed below.
Table 1.1 Status and meanings of each LED (operation panel (controller enclosure))
LED name LED status ETERNUS DX Disk storage system status
POWER
(green)
DC power is supplied to the controller enclosure.
READY
(green)
The ETERNUS DX Disk storage system is available for use.
FAULT
(amber)
The ETERNUS DX Disk storage system is in error status.
(blinks amber)
A part of the ETERNUS DX Disk storage system requires preventive
maintenance.
MAINT/ID
(green)
Maintenance for the ETERNUS DX Disk storage system is in
progress.
(blinks green)
•As ordered via ETERNUS Web GUI or ETERNUS CLI, the location
of the controller enclosure is identified.
•Maintenance or a status check via ETERNUS Web GUI or
ETERNUS CLI is necessary.
CACHE
(green)
There is data in the ETERNUS DX Disk storage system cache
memory.

Chapter 1 Components
1.1 Controller Enclosure
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
16
■Drives
●2.5" drives
Figure 1.7 2.5" drive
Figure 1.8 shows the slot number of each drive.
Figure 1.8 Drive slot numbers (2.5" type controller enclosure)
●3.5" drives
Figure 1.9 3.5" drive
Figure 1.10 shows the slot number of each drive.
Figure 1.10 Drive slot numbers (3.5" type controller enclosure)
DRIVE READY LED DRIVE FAULT LED
Slot#8 Slot#9 Slot#10
Slot#11
Slot#12 Slot#13 Slot#14 Slot#15 Slot#0 Slot#1 Slot#2 Slot#3 Slot#4 Slot#5 Slot#6 Slot#7 Slot#16 Slot#17 Slot#18 Slot#19 Slot#20 Slot#21 Slot#22 Slot#23
DRIVE READY LED
DRIVE FAULT LED
Slot#0
Slot#4
Slot#8
Slot#1
Slot#5
Slot#9
Slot#2
Slot#6
Slot#10
Slot#3
Slot#7
Slot#11

Chapter 1 Components
1.1 Controller Enclosure
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
17
●Part explanation
•LEDs
The states of LEDs are listed below.
Table 1.2 Status and meanings of each LED (drive)
1.1.4 Components (Rear)
This section describes the controllers and the power supply units in the rear of the controller enclosure.
1.1.4.1 Controllers
The controller contains a CPU, cache memory, System Capacitor Unit (SCU), host interfaces, drive interface (DI)
ports, and LAN ports. The controller controls all operations in the ETERNUS DX Disk storage system.
Figure 1.11 Controller
LED name LED status Drive status
DRIVE READY
(green)
The drive is in normal status.
(blinks green)
DRIVE FAULT
(amber) •The drive is in error status.
•In response to commands from ETERNUS CLI, the location of
the drive is identified.
LAN (MNT) port
ACT LEDs
LINK LEDs
DI (OUT) LINKUP LED
READY/FAULT LED
MASTER LEDUNIT ID LED
CA#0 FAULT LED
PWC port
LINK/FAULT LEDs
DI (OUT) port
LAN (RMT) port
Host interface (CA#0) Host interface (CA#1)
CA#1 FAULT LED

Chapter 1 Components
1.1 Controller Enclosure
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
18
●Part explanation
•LAN (RMT) port, LAN (MNT) port
These ports are RJ-45 connectors for LAN cables.
•Host interface (CA#0), host interface (CA#1)
Install host interfaces. For details, refer to "Host interfaces" (page 19).
•DI (OUT) port
This port is used to connect a controller enclosure to a drive enclosure with a QSFP cable.
•PWC port
This port is used to connect a power synchronization unit with an RS232C cable.
•LEDs
The states of LEDs are listed below.
Table 1.3 Status and meanings of each LED (controller)
LED name LED status Controller status
READY/FAULT
(green)
The controller is in normal status.
(amber) •The controller is performing the initial setup after the power
is turned on.
•The controller is in error status.
(blinks amber)
MASTER
(green)
The controller is set as a Master CM.
UNIT ID
(blinks green)
•As ordered via ETERNUS Web GUI or ETERNUS CLI, the location
of the controller is identified.
•System Capacitor Unit (SCU) is charging.
CA FAULT
(amber)
The host interface is in error status.
LINK/FAULT
(green)
The link between the host interface port and the destination has
been established.
(amber)
The host interface port is in error status.
DI (OUT) LINKUP
(green)
The link between the DI (OUT) port and the destination port has
been established.
ACT
(green)
The controller is sending or receiving data via the LAN port (for
operation management).
LINK
(green)
The link between the LAN port (for operation management) and
the destination has been established.

Chapter 1 Components
1.1 Controller Enclosure
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
19
■Host interfaces
A host interface is a board that has interface ports to connect a controller to the server.
There are six types of host interfaces: FC 16Gbit/s, FC 8Gbit/s, iSCSI 10Gbit/s, iSCSI 1Gbit/s, FCoE, and SAS.
●FC, iSCSI 10Gbit/s, FCoE (for FC cable connection)
Figure 1.12 Host interface (FC, iSCSI 10Gbit/s, FCoE (for FC cable connection))
•Part explanation
-Host interface ports (FC, iSCSI 10Gbit/s, FCoE (for FC cable connection)) (from left to right: Port#0 and
Port#1 in CA#0, Port#0 and Port#1 in CA#1)
These are the Dual LC connectors to connect FC cables.
Port#0 Port#1 Port#0 Port#1
FC iSCSI 10Gbit/s FCoE
Installed host interfaces in the controller
Host interface (CA#0) Host interface (CA#1)

Chapter 1 Components
1.1 Controller Enclosure
ETERNUS DX80 S2/DX90 S2 Disk storage system User’s Guide -Operation-
Copyright 2013 FUJITSU LIMITED P3AM-4842-12ENZ0
20
●iSCSI 10Gbit/s, FCoE (for Copper Twinax cable connection)
Figure 1.13 Host interface (iSCSI 10Gbit/s, FCoE (for Copper Twinax cable connection))
•Part explanation
-Host interface ports (iSCSI 10Gbit/s, FCoE (for Copper Twinax cable connection)) (from left to right:
Port#0 and Port#1 in CA#0, Port#0 and Port#1 in CA#1)
These are the connectors to connect Copper Twinax cables.
●iSCSI 1Gbit/s
Figure 1.14 Host interface (iSCSI 1Gbit/s)
•Part explanation
-Host interface ports (iSCSI) (from left to right: Port#0 and Port#1 in CA#0, Port#0 and Port#1 in CA#1)
These are the RJ-45 connectors to connect LAN cables.
Port#0 Port#1 Port#0 Port#1
iSCSI 10Gbit/s, FCoE
Installed host interfaces in the controller
Host interface (CA#0) Host interface (CA#1)
iSCSI 1Gbit/s
Port#0 Port#1Port#0 Port#1
Installed host interfaces in the controller
Host interface (CA#0) Host interface (CA#1)