Furniture of America CM3557T User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM3557T
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-08-20
Page 1 of 6
DIFFICULT
ASSEMBLY RATING
2 PERSONS RECOMMENDED
Wrench (Included)

Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment
to providing quality products does not simply end when a purchase is made. We
stand behind our products and will provide any support needed in order for you to
fully enjoy your purchase. Your satisfaction is the greatest recognition we could
have.
Because we value your trust in our company, we will do our best to meet your
service expectations. Should you have any assembly related questions, parts
replacement requests, comments or suggestions, please feel free to contact us any
time. To help expedite the service, please have the assembly instructions available,
along with your order receipt.
[email protected]
www.foagroup.com
Toll-Free 1-888-980-5122 or 1-626-363-9311
1-626-270-4451
Monday to Friday 8:30 a.m. to 5:30 p.m. (PST)
https://twitter.com/foagroup
http://www.pinterest.com/foagroup/
http://instagram.com/foagroup#
https://www.youtube.com/user/FurnitureOfAmerica
Page 2 of 6

Page 3 of 6

Parts List
#1 x 1 pc
Table Top
#2 x 2 pcs
Leaf
#3 x 2 pcs
Table Base
#D x 1 pc
Allen Wrench
Before you begin, please read Page 3
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
MD
#C x 16 pcs
Bolt 5/16”x2”
#4 x 2 pcs
Leg
Page 4 of 6
#E x 2 pcs
Hex Nut
Hardware List
#5 x 1 pc
Leg Support
#A x 18 pcs
Flat Washer
#B x 18 pcs
Lock Washer
#G x 2 pcs
Threaded Stud
#H x 2 pcs
Beveled Washer
#F x 1 pc
Wrench
Due to the size and/or weight of this
product, it is highly recommended that the
assembly should be done near the area of
its intended location. Make sure you have
enough space to move around during the
assembly.ALWAYS have at least two
people to help with transporting and
assembling the product to avoid any
potential injury and/or damage.

Page 5 of 6
Turn right (clockwise) to tighten
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
I. Insert the two threaded studs (#G) into the legs (#4).
II. Insert the leg support (#5) onto the threaded studs (#G) of the legs
(#4). Then insert the beveled washer (#H), the flat washer (#A)
and the lock washer (#B), in that order onto the threaded stud
(#G).
III. Secure the hex nut (#E) onto the threaded stud (#G) using the
wrench (#F) to tighten. Repeat the process to secure the other
side of the leg support (#5) onto the other threaded stud (#G).
#A x 2 pcs
#B x 2 pcs
#E x 2 pcs
#G x 2 pcs
#H x 2 pcs
I. Align the table base (#3) with the
pre-drilled holes on the leg (#4).
II. Prepare 4 bolt assemblies by
inserting FIRST the lock washer (#B)
onto the bolt (#C) and then the flat
washer (#A) onto the SAME bolt
(#C), in that order.
III. Insert the bolt assemblies through
the pre-drilled holes on the table
base (#3) and secure those bolts
using the Allen wrench (#D) to lock
them with the leg (#4).
IV. Repeat the process above to
assemble the second table base (#3)
onto the second leg (#4)

Page 6 of 6
Turn right (clockwise) to tighten
#A x 8 pcs
#B x 8 pcs
#C x 8 pcs
I. With the help of another person,
carefully place the table top (#1)
facing down on a protected surface.
II. Align the assembled table base (#3)
with the pre-drilled holes on the
bottom of the table top (#1)
III. Prepare 8 bolt assemblies by
inserting FIRST the lock washer (#B)
onto the bolt (#C) and then the flat
washer (#A) onto the SAME bolt
(#C), in that order.
IV. Insert the bolt assemblies through
the pre-drilled holes of the table
bases (#3) and secure those bolts
using the Allen wrench (#D) to lock
them with the table top (#1).
V. Carefully turn the completed table
upright. Make sure the table is
rested on a flat surface and does not
feel loose or wobbly. If it does,
double check that the bolts/screws
are secured and properly tightened.
I. To insert the table leaf or leaves (#2) unlock the latches located
under the table top (#1).
II. Once unlocked, slide outward on both ends of the outer-piece
table until there is sufficient opening to place the table leaf or
leaves (#2). Then slide inward on both ends of the outer-piece
table until they are touching and sitting flush with the table leaf or
leaves (#2).
III. Secure the parts together by locking the latches located under
the table top (#1).
ASSEMBLY IS COMPLETED