Furniture Solutions 18WASLD.S User manual

1
INSTRUCTION MANUAL
WASHINGTON 6PC LOUNGE DINING
ITEM CODE: 18WASLD.S
Imported by Furniture Solutions (Aust) Pty Ltd New South Wales, Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
Email- customer[email protected]om.au

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage
the product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
2
20
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2

3
PARTS LIST
A Table rim P.18WAS-T.R
B Leg P.18WAS-T.L
C Plate P.18WAS-T.PL
D Glass Panel P.18WAS-T.GP
E Flat washer P.18WAS-T.HW
F Bolt P.18WAS.T.HW
G Spring washer P.18WAS.T.HW
H Cover Cap P.18WAS.T.HW

4
COMPONENTS LIST
Back Cushion 57*44*10cm P.18WAS.BC
Seat Cushion 61*57*10cm P.18WAS.SC
Frame 79*81*80cm P.18WAS1S-3.F
Back Cushion 57*44*10cm P.18WAS.BC
Seat Cushion 61*57*10cm P.18WAS.SC
Frame 200*81*80cm P.18WAS3S.F
Seat Cushion 400*400*10cm P.18WASS.SC
Frame 40*40*40cm P.18WASS.F

5
ASSEMBLY INSTRUCTION
Assembly Dining Table-Fit Leg
Please prepare work area as set out on page 2:
As indicate in diagram below lay table rim [B] upside down. With the help of a second person
take leg [c] aline holes at top of leg with threaded holes in rim and then by hand insert bolt [D]
with washer [E] thru hole in leg and into threaded hole, turn bolt 2-3 times to ensure thread has
gripped correctly. Test by lightly pulling back on bolt. DO NOT TIGHTEN. Repeat for other 3
bolts. Once all bolts are seated correctly, take tool [G] and tighten bolt until they feel firm. Do
not overtighten as you may cause damage to thread. Repeat for other leg.
Move to next page.

6
ASSEMBLY INSTRUCTION
Assembly Dining Table-Fit Glass
Please prepare work area as set out on page 2:
With the help of a second person lift table frame into air and roll over until all feet are level with
ground, then gently lower. Next again with help lift glass panel [A] horizontally and place as per
diagram below. When moving table always lift with the help of another person. Never drag
table.
Assembly complete.

7
CARE & MAINTENANCE
Varieties of materials are used in construction of “Outdoor” furniture ranges.
All will require some form of maintenance to extend the life of finishes and general appearance.
Please see below instruction unique to your chosen product.
Washington Range Construction;
Table Tops: Tempered Glass
Frame: Aluminium
External Covering: Synthetic Wicker
Textile: Polyester “Spun Poly”
Glass panel:
Glass used is tempered for your safety; best results are to use table cloths, placemats &
coasters to avoid scratching surface. Keep dust free, clean underside of glass with a soft clean
cloth. Use of normal glass cleaning product is permissible but please rinse surrounding areas
with clean water to avoid damage to other materials used in construction of item.
Aluminium Frame:
The majority of frames are mainly produced from aluminium, with the main benefit being a
light weight product for easier use. Some designs require steel to be used in certain sections for
added strength. While aluminium is rust resistant, bare metal can show signs of oxidation (red
film) this does not constitute rust. Simply you are able to wipe or sand surface to remove
oxidation mark.
Note you will need to touch up affected area with paint to stop from reoccurring. Steel itself has
a lower resistance to elements than aluminium and will show signs of rust as it ages. Limited
exposure & maintenance are best solutions for adding life to any furniture used in outside
areas.
Aluminium Frame Maintenance
Use a bucket filled with warm water & a soft soap, sponge over frame till clean, once clean rinse
off with a hose, pat dry with a soft clean cloth before use. Every 4-6 weeks.
Note when cleaning if you find scratches in paint please cover with a paint to prevent oxidation.

8
CARE & MAINTENANCE
Synthetic Wicker Fibre Information
Synthetic Wicker fibre (commonly referred to as resin wicker) is made of polyethylene
combined with colour & UV stabilizer. While the UV stabilizer adds to the life of the synthetic
fibre, the effectiveness of stabilizer diminishes with age.
Longevity of use cannot be judge as environmental conditions and are too varied to set a
standard. Protection from the harsh outdoor conditions (I.e. Sunlight, pollution) is best for a
longer period of use.
Synthetic Wicker Fibre Maintenance
Use a bucket filled with warm water & a soft soap, sponge over fibre till clean once clean rinse
off with a hose, pat dry with a soft clean cloth before use. Regular regime.
Fabric Information
Fabrics used in outdoor product are not made of any special type of material; they do however
use blends of common materials such as polyester, olefin & acrylic which perform best for
intended purpose. These fabrics are not impervious to fading or mould, ensure cushions are
always dry and put away when not in use.
Fabric Maintenance
It is important to keep fabric free of dust and or debris. Please vacuum regularly.
Spot cleaning warm water & soft soap solution, sponge onto affected area till clean rinse area
with clean sponge, pat dry with a soft clean cloth.
Stubborn stains may be removed with fabric cleaner or if available steam cleaning is ok
providing covers are left on filling and on gentle setting.
Note; do not use solvents, PH Neutral cleaning products only.
do not machine wash, hand wash only
do not tumble dry,

9
SAFETY WARNINGS AND ADVICE
Notices and Advice
Please be advised that products are limited in design for residential use only and are not
suitable for commercial use.
Please be advised that materials used in your furniture are not impervious to neglect, acts of
god, abuse, alcohol spills, improper use of chemicals such as bleach or any solvent based
products.
Please be advised that heat sources such as barbeques, open fires, temporary/mobile/overhead
heaters, poorly insulated candle holders, hot pots, pans, hot serving dishes can have adverse
affects on your furniture.
Please be advised to use properly insulted placemats and coasters when serving hot or cold
dishes and drinks.
Please be advised that fitting, bolts, nuts and or screws should be checked periodically to
ensure they have not loosened over time. Remember do not overtighten.
Please be advised coverings and paint finishers are not animal proof. Claws can scratch covering
& saliva is acidic and can damage finish.
Please be advised that continues exposure to the elements will reduce the life of finishes and
fittings.
DO NOT
•Place in close proximity to open flame or heaters.
•Leave spills or food, clean off immediately
•Pull loose thread, cut them instead.
•Sit or lean on arms
•Stand on chair or bench's
•Stand on table tops
•Place heavy objects on table tops
•Place objects such as pot plants as a display piece on tables recommend weight restriction
for table top is 60kg across the table
Safety warnings
•DO NOT:
•drop, drag always move furniture with the help of another person lift and place only
•Over load bench seats recommended weight evenly distributed is 240kg IE: 2 people 120kg
each.
•Tables, chairs & bench's are designed for seating, not work bench's.
•Allow child to play under table

10
WARRANTY DETAILS
1 Year Warranty
A one (1) year warranty applies to product against any defect associated with faulty workmanship
for a period of (1) year from date of purchase.
Extended Warranty of (1) year total of (2) years applies to aluminum frame, welds & resin wicker
against any defect associated with faulty workmanship from date of purchase.
Furniture Solutions accepts no responsibility for defects caused by incorrect assembly, mishandling,
acts of god, general wear & tear, stains from spills/vegetation, chipping/scratching, exposure to
extreme heat/cold, mould/mildew, hardware corrosion, misuse of the products & defects caused by
failure in duty of care for the product in accordance with the care instructions. Warranty only
extends to original purchaser and is not transferable, except when given as a gift.
Products are limited in design for domestic use and not suited for commercial use.
Do not place near or place on product any heat sources such as BBQ’s, heaters or any open flame
devices.
Duty of care:
While every attempt is made to supply product using quality components there is always a need
from consumer to help ensure a long life of use for product.
*Proper use of item, only what it is designed to do
*Regular maintenance and cleaning
To extend the life of your outdoor furniture we recommend the following furniture covers should be
used on furniture which is used in areas not protected from elements. Caution should be used
when using oils, lotions & other chemicals such as chlorine.
Instruction Manual –Have been written to suit individual materials used in construction, please
retain for future use for duty of care, assembly, parts & component sizing.
Claim management:
To make a warranty claim, customers can either contact the retailer where the purchase was made
or Furniture Solutions on contact details below. Proof of purchase will be required before
proceeding with any claim. In the case of product defects providing photos may be able to speed up
processing of the claim. If missing parts please refer to assembly instructions for identification of
said part and contact either of the above.
“Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You
are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced
if the goods fail to be of acceptable quality and the failure does not amount to a major failure”.